Tda2546a.pdf part of Philips TDA2546a Tda2546a.pdf, Philips Quality Data Sheet text manual preview

Text preview for : Tda2546a.pdf part of Philips TDA2546a Philips Quality Data Sheet

Back to : Tda2546a.pdf | Home

INTEGRATED CIRCUITS

DATA SHEET

TDA2546A Quasi-split-sound circuit with 5,5 MHz demodulation
Product specification File under Integrated Circuits, IC02 February 1985

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation
GENERAL DESCRIPTION

TDA2546A

The TDA2546A is a monolithic integrated circuit for quasi-split-sound processing, including 5,5 MHz demodulation, in television receivers. Features 1st i.f. (V.C.: vision carrier plus S.C.: sound carrier) · 3-stage gain controlled i.f. amplifier · A.G.C. circuit · Reference amplifier and limiter amplifier for vision carrier (V.C.) processing · Linear multiplier for quadrature demodulation 2nd i.f. (5,5 MHz signal) · 8-stage limiter amplifier · Quadrature demodulator · A.F. amplifier with de-emphasis · AV switch QUICK REFERENCE DATA Supply voltage (pin 15) Supply current (pin 15) Minimum i.f. vision carrier input voltage (r.m.s. value) Output voltage; 5,5 MHz (r.m.s. value) Output voltage; 5,742 MHz (r.m.s. value) I.F. control range Signal-to-weighted-noise ratio (rel. to 1 kHz; 30 kHz deviation) at 5,5 MHz for 2T/20T pulses with white bars at 5,742 MHz A.F. output voltage (r.m.s. value) PACKAGE OUTLINES 18-lead DIL; plastic (SOT 102); SOT102-1; 1996 November 19. S + W/W Vo6-16(rms) typ. typ. 56 0,6 dB V S + W/W typ. 58 dB VP = V15-16 IP = I15 VVC1-18 (rms) V14-16(rms) V14-16(rms) Gv typ. typ. typ. typ. typ. typ. 12 57 150 100 45 64 V mA µV mV mV dB

February 1985

2

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation

TDA2546A

February 1985

3

(1) I.F. signal: vision carrier (V.C.) and sound carrier (S.C.)

Fig.1 Block diagram.

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation
RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) Supply voltage (pin 15) Input current (pin 4) Storage temperature range Operating ambient temperature range VP = V15-16 I4 Tstg Tamb

TDA2546A

max. 13,2 max. 7 -25 to +150 0 to +70

V mA °C °C

February 1985

4

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation

TDA2546A

CHARACTERISTICS VP = V15-16 = 12 V; Tamb = 25 °C; measured at fVC = 38,9 MHz, fSC1 = 33,4 MHz, fSC2 = 33,158 MHz: Vision carrier (V.C.) modulated with different video signals (see below); modulation depth 100% (proportional to 10% residual carrier). Vision carrier amplitude (r.m.s. value) is VVC = 10 mV. Vision-to-sound carrier ratios are VC/SC1 = 13 dB and VC/SC2 = 20 dB. Sound carriers (SC1, SC2) modulated with f = 1 kHz and deviation f = ± 30 kHz. For measuring circuit see Fig.2; unless otherwise specified. PARAMETER Supply (pin 15) Supply voltage Supply current I.F. amplifier Input voltage for start of gain control (intercarrier signals -3 dB) Input voltage for end of gain control (intercarrier signals + 1 dB) I.F. gain control range Control voltage range (see Fig.3) Input resistance Input capacitance Intercarrier generation Output voltage; 5,5 MHz (r.m.s. value) Output voltage; 5,742 MHz (r.m.s. value) D.C. output voltage Allowable d.c. load resistance at the output Allowable output current Frequency demodulator (measured at f = 5,5 MHz) Input voltage vor start of limiting (r.m.s. value) Maximum input voltage (r.m.s. value) D.C. output voltage A.F. output voltage (r.m.s. value) D.C. output voltage Allowable d.c. load resistance at the output Allowable a.c. load impedance at the output Total harmonic distortion Internal de-emphasis resistance Switching voltage (pin 4) for mute for a.f. on V4-16 V4-16 9 - - - - 2,5 V V V12-16(rms) V12-16 (rms) V11,12,13-16 V6-16(rms) v6-16 R6-16 Z6-16 THD Ri5-16 - - - 450 - 27 10 - - - 200 2,2 600 4 - - - 1 100 - - 810 - - - 1 - µV mV V mV V k k % k V14-16(rms) V14-16(rms) V14-16 R14-16 -I14 60 27 - 7 - 100 45 5,9 - - 140 63 - - 1 mV mV V V mA VVC1-18 (rms) Gv V3-16 R1-18 C1-18 100 60 4 - - 250 64 - 2,5 1,5 - - Vp - - mV dB V k pF VVC1-18(rms) - 150 200 µV VP = V15-16 IP = I15 10,8 40 12 57 13,2 75 V mA SYMBOL MIN. TYP. MAX. UNIT

February 1985

5

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation
PARAMETER Intercarrier signal-to-noise (measured behind the FM demodulators) Signal-to-weighted-noise ratio according to CCIR 468-2, quasi-peak 2T/20T pulses with white bars (see also Fig.4) at 5,5 MHz at 5,742 MHz 6 kHz sine wave at 5,5 MHz at 5,742 MHz with black level (vision carrier modulated with sync pulses only) at 5,5 MHz at 5,742 MHz Notes to the characteristics S+W/W S+W/W 60 58 65 63 S+W/W S+W/W 50 50 53 53 S+W/W S+W/W 53 51 58 56 SYMBOL MIN. TYP.

TDA2546A

MAX.

UNIT

- - - -

dB dB dB dB

- -

dB dB

1. Incidential phase on the vision carrier, caused by TV-transmitter, has to be less than 0,5 degrees for black to white transient. (Equivalent to S+W/W = 56 dB for 6 kHz sine wave).

February 1985

6

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation

TDA2546A

(1)

I.F. signal: vision carrier (V.C.) and sound carrier (S.C.)

Fig.2 Measuring circuit for TDA2546A.

Fig.3 Control voltage at pin 3 as a function of the input voltage VVC1-18(rms).

February 1985

7

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation

TDA2546A

Fig.4 Signal-to-weighted-noise ratio depending on video modulation.

February 1985

8

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation
PACKAGE OUTLINE DIP18: plastic dual in-line package; 18 leads (300 mil)

TDA2546A

SOT102-1

D seating plane

ME

A2

A

L

A1

c Z e b1 b 18 10 b2 MH w M (e 1)

pin 1 index E

1

9

0

5 scale

10 mm

DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.7 0.19 A1 min. 0.51 0.020 A2 max. 3.7 0.15 b 1.40 1.14 0.055 0.044 b1 0.53 0.38 0.021 0.015 b2 1.40 1.14 0.055 0.044 c 0.32 0.23 0.013 0.009 D (1) 21.8 21.4 0.86 0.84 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.10 e1 7.62 0.30 L 3.9 3.4 0.15 0.13 ME 8.25 7.80 0.32 0.31 MH 9.5 8.3 0.37 0.33 w 0.254 0.01 Z (1) max. 0.85 0.033

Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT102-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION

ISSUE DATE 93-10-14 95-01-23

February 1985

9

Philips Semiconductors

Product specification

Quasi-split-sound circuit with 5,5 MHz demodulation
SOLDERING Introduction

TDA2546A

There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.

February 1985

10