Text preview for : Lens-Screen-DiamondShield-VS-50805-60805-WS-55805.pdf part of Mitsubishi VS-50805, WT-60805, WS-55905, WS-65905, WS-73905, WS-55805, WT-46805 Mitsubishi VS-50805, WT-60805, WS-55905, WS-65905, WS-73905, WS-55805, WT-46805 (Chassis V16 N W) (Training Manual + Schematic)
Back to : Mitsubishi VS-50805, 6080 | Home
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
CAUTION: Wear gloves when handling the Lenticular Screen and Fresnel Lens. This prevents cuts and finger prints. Do not place Fresnel Lens in the sun. This may cause fine and heat related injuries.
VS-50805 / VS-60805 / WS-55805 1. Lenticular Screen and Fresnel Lens Removal
1. Remove the screen assembly shown in the Cabinet Disassembly procedure. 2. Remove the Frame Holder by removing 12 screws (a). 3. Remove Screen Holder by removing 6 screws (b). Note: When separating the Lenticular Screen from the Fresnel Lens, use caution while prying the Screen and Lens apart. Use a slot type screw drive, and remove the pressure sensitive double sided tape.
Page 10
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
2. Lenticular Screen and Fresnel Lens Installation.
Note: Store the Lenticular Screen and Fresnel Lens in a cool dry place. High humidity may deform the Lenticular Screen and Fresnel Lens. 1. Apply double coated tape (Part # LENS-TAPE) along the top front edge of the Fresnel Lens as shown below. Refer to the Table below for proper tape length. 2. Place the Fresnel Lens on top of the Lenticular Screen and apply pressure at the top edge to bond them together as shown below.
MODEL VS-50805 VS-60805 WS-55805 WS-55905 WS-65905 WS-73905 WT-46805
SCREEN TAPE SIZE LENGTH 50" 60" 55" 55" 65" 73" 46" 37.5" 45" 45" 45" 53" 60" 37.5"
Page 12
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905 SERVICING THE DIAMONDSHIELD 1. DiamondShield Removal Procedure
Note: Wear gloves when handling the DiamondShield to prevent finger prints.
1. Remove the left and right molding clips by gently inserting a small screwdriver between the DiamondShield and one end of the clip.
2. Gently pry both clips loose and remove them by pulling toward you.
3. Carefully insert a small screwdriver into the gap between the DiamondShield and the Lenticular Screen at the top/center point. Pivot the screwdriver up and forward to pull the top edge of the DiamondShield slightly away from the unit. Then, with your left and right hands placed at the approximate points shown, gently bow the DiamondShield toward you and away from the unit to remove.
4. Complete the DiamondShield removal by replacing the molding clips removed in step 2. For both the left and right, press the clip into place starting at one corner. Then, run a finger along the length of the clip to press it into place. Do not force.
Page 13
MODELS: VS-50805 / VS-60805 / WT-46805 / WS-55805 / WS-55905 / WS-65905 / WS-73905
2. DiamondShield Installation Procedure *(See Parts List for DiamondShield part numbers)
1. Remove the left and right molding clips by gently inserting a small screwdriver between the DiamondShield and one end of the clip.
2. Gently pry both clips loose and remove them by pulling toward you.
3. Install the DiamondShield by first inserting the right edge into the side channel. Then, with your left and right hands placed at the approximate points shown, gently bow the shield toward you and insert the left end of the DiamondShield into the left side channel.
4. Complete the DiamondShield installation by replacing the molding clips removed in step 2. For both the left and right, press the clip into place starting at one corner. Then, run a finger along the length of the clip to press it into place. Do not force.
Page 14