Text preview for : Samsung TXM1367X-XAA, TXM1367X-XAC, TXM1997X-XAA, TXM1997X-XAC, TXM1967X-XAA (Chassis K15D) (Service part of TXM1367X/XAA, TXM1367X/XAC, TXM1997X/XAA, TXM1997X/XAC, TXM1967X/XAA Samsung TXM1367X/XAA, TXM1367X/XAC, TXM1997X/XAA, TXM1997X/XAC, TXM1967X/XAA (Chassis K15D) (Service Manual)
Back to : Samsung TXM1367X-XAA, TXM | Home
COLOR TELEVISION RECEIVER
Chassis : Model : K15D TXM1367X/XAA TXM1997X/XAA TXM1967X/XAA TXM1367X/XAC TXM1997X/XAC
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions 2. Specifications and IC Data 3. Disassembly and Reassembly 4. Alignment and Adjustment 5. Troubleshooting 6. Exploded View and Parts List 7. Electrical Parts List 8. Block Diagram 9. Wiring Diagram 10. Schematic Diagrams
ELECTRONICS
© Samsung Electronics Co., Ltd. APR.2002
Printed in Korea AA82-
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
1-4
Samsung Electronics
Specifications and IC Data
2. Specifications and IC Data
2-1 Specifications
Television System:
MODEL CT
SYSTEM NTSC ONLY
System Band Channels: VHF UHF CABLE
NTSC 2 - 13 14 - 69 1 - 125
Intermediate Frequencies (MHz) :
SYSTEM IF Carrier Frequency Picture IF Carrier Sound IF Carrier Color Sub Carrier NTSC 45.75 41.25 42.18
Picture Tube:
14 Inch 15 Inch 20 Inch 21 Inch
A34KQV42X A36QDT351X A48KRD82X A51KQJ63X
14Inch 15Inch Flat 20Inch 21Inch
Power Requirements: Antenna Input Impedance: Speaker Impedance
AC 120V, 60Hz VHF, UHF : Telescopic dipole antenna (75 ohm unbalanced type ) 8 ohm
Samsung Electronics
2-1
Specifications and IC Data
2-2 IC Line Up
Table 2-1 IC Line-Up
Loc. No
IC201S
IC301 IC501
Specificatio
SPM458AN LA7840
TDA6107Q
Description
TDA9377, English/Spanish/French
VERTICAL OUTPUT RGB DRIVE AMP TDA7266M (MONO) TDA7266S (STEREO)
Remark
Philips
Sanyo
Philips
IC602 IC801S IC802 IC202 PC801S ICS601
TDA7266M/TDA7266S
KA5Q0740RT (0765RT) KA7632 24C04 TCET1108 / LTV817B UPC1851B
SOUND-AMP,
POWER IC (STR)
Philips FIAIR CHILD
SEC
CUSTOM REGULATOR (5V, 8V, 3.3V) EEPROM PHOTO COUPLER Sound Processor (STEREO)
NEC
2-2
Samsung Electronics
Specifications and IC Data
2-3 Semiconductor Base Diagrams
ELECTROLYTICCONDENSER
DIODE
IC SPM458AN(Pin 64) U4468B(Pin 16) UPC851B(Pin 42)
TRANSISTOR
TRANSISTOR
SAW-FILTER M1864M
KSC5802 KSC815-Y KSA539-Y
1
11
B
C
E
E B C
IC LA7840 TDA6107Q KA7632
TRANSISTOR
KSC2331-Y
E C B
Fig. 2-1 Semiconductor Base Diagrams
Samsung Electronics
2-3
MEMO
2-4
Disassembly and reassembly
3. Disassembly and Reassembly
3-1 Back Cover Removal
1. After removing the screws, press the tension rib and pull the cabinet backwards. 2. To reassemble, press the tension rib (see diagram).
Samsung Electronics
3-1
Disassembly and reassembly
3-2 Main Board Removal
1. Separate the socket board from the CRT neck. 2. Remove the Anode Cap from the CRT. 3. Remove the main board by pulling it with both hands. Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board.
3-3 Speaker Removal
1. Remove the speaker by pressing the tension rib.
3-2
Samsung Electronics
Disassembly and reassembly
3-4 CRT Removal
1. Spread a soft mat on the floor. Place the TV set face down. 2. Remove the 4 nuts mounting the CRT to the front cabinet. Lift the CRT. 3. Caution: Because of the high vacuum and large surface area of the picture tube, be careful while handling it: (1) Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure. Fractures of the glass may cause an implosion.
Samsung Electronics
3-3
MEMO
3-4
Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments
4-1 Preadjustment
4-1-1 Factory Mode
1. Do not attempt these adjustments in the Video Mode. 2. The Factory Mode adjustments are necessary when either the EEPROM (IC902) or the CRT is replaced. 3. Do not tamper with the "Adjustment" screen of the Factory Mode menu. This screen is intended only for factory use.
4-1-3 When CRT Is Replaced
1. Make the following adjustments AFTER setting up after setting up purity and convergence : White Balance Sub-Brightness Vertical Center Vertical Size Horizontal Size Fail Safe (This adjustment must be the last step). 2. If the EEPROM or CRT is replaced and set SC as 20(factory mode).
4-1-2 When EEPROM (IC902) Is Replaced
1. When IC902 is replaced all adjustment data revert to initial values. It is necessary to re-program this data. 2. After IC902 is replaced, warm up the TV for 10 seconds.
4-2 Factory/Service Mode
4-2-1 Procedure for the "Adjustment" Mode
1. This mode uses the standard remote control. The Service Mode is activated by entering the following remote-control sequence : (1) DISPLAY FACTORY. (2) STAND-BY MUTE 1 8 2 POWER ON. 2. The "SERVICE (FACTORY)" message will be displayed. The Service Mode has four components: ADJUST, OPTION , G2-ADJUST and RESET. 3. Access the Adjustment Mode by pressing the "VOLUME" keys ( Up or Down). The adjustment parameters are listed in the accompanying table, and selected by pressing the CHANNEL keys ( , ). 4. Selection sequences for the all system: DOWN or UP key: SCT>SBT>BLR>BLB>RG>GG>BG>VSL>VS> VA>HS>SC>CDL>STT>AKB>FS>NDL> LBS>NSR>SCBT>VOL>CAP>HBS>RP00> RP01>FMWS>AGC1>OMD>SCL>PWL> MUS>AGC>DSK>DVDB 5. The VOLUME keys increase or decrease the adjustment values (stored in the non-volatile memory) when Adjustment Mode is cancelled. 6. Cancel the Adjustment Mode by re-pressing the "FACTORY" or "Power OFF" keys.
Samsung Electronics
4-1
Alignment and Adjustments
4-2-2 Main Adjustment Parameter
SETTING NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 OSD SCT SBT BLR BLB RG GG BG VSL VS VA HS SC CD L ST T AKB FS ND L LBS NSR SCBT VO L CAP HBS RP00 RP01 FMWS AGC1 OMD SCL PWL MUS AGC DSK DVDB FUNCTION Su b Co n t ra s t Su b Bri g h t n e s s Bl a c k Le v e l o f fse t Red Bl a c k Le v e l o f fse t Blu e R ed Gain G re e n G a i n Bl u e G a i n Ve r t i ca l S lo p e Ve r t i ca l Sh i f t Ve r t i ca l A m p l i tu d e H o r i z o n t a l Sh i f t S- Co r r e c t i o n Ca t h o d e Dri ve Le ve l Su b T i n t AK B O n / o ff Filter Seting NT SC De l a y Low Band Separation Set N T SC Su b c o l o r S c re e n B ri gh rtn e s s Vo l u m e p re s e t t i n g C a p ti on P o s i ti o n Hig h B a n d S e p a ra ti on S e t R a ti o Pre / o v e rs h o o t R a ti o Pre / o v e rs h o o t W i nd o w S el ec ti on S o u n d PL L IF A G C S p e e d Offs et I F D em od u l ato r S o ft C l i p p i ng L ev e l P e a k W hi te L i m i tti ng M a tri x U S A Auto m ati c G a i n C o n tro l Dy na m i c S k i n To n e DV D B ri gh t O ffs et RANGE 0 ~ 23 0 ~ 23 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 15 0 ~ 7 0 ~ 1 0 ~ 15 0 ~ 15 0 ~ 63 0 ~ 23 0 ~ 63 0 ~ 63 0 ~ 15 0 ~ 63 0 ~ 1 0 ~ 1 0 ~ 1 0 ~ 3 0 ~ 63 0 ~ 3 0 ~ 15 0 ~ 1 0 ~ 63 0 ~ 1 0 ~ 10 INITAL DATA 15 8 35 32 40 30 42 30 31 20 32 35 11 3 0 32 1 32 3 35 10 12 32 1 1 0 1 32 3 15 0 33 0 5 19V 13 9 31 27 32 25 31 31 31 40 30 20 11 7 0 37 1 32 3 45 10 12 32 1 1 0 1 32 1 13 0 33 0 4 13V 13 9 31 27 32 25 31 31 31 20 30 12 7 7 0 37 1 32 3 45 10 12 32 1 1 0 1 32 1 13 0 33 0 4 REMARK W/B (HIGH Y) W/B A (LOW Y) W/B (LOW X, Y) W/B (LOW X, Y) W/B (HIGH X, Y) FIX W/B (HIGH X, Y) Vertical SLOPE FIX Vertical SIZE Horizontal SHIFT FIX FIX FIX FIX FIX(STEREO) FIX FIX(STEREO) FIX FIX FIX FIX FIX(STEREO) FIX FIX FIX (Mono) FIX (Nomal) FIX (No Crrection) FIX (Off) FIX (100%) FIX (Mono) FIX FIX FIX
4-2
Samsung Electronics
Alignment and Adjustments
4-2-3 Option Bytes
In the Service Mode, various can be selected via the Option Table. Example:
Option Table : xx xx
OSD VIDEO MUTE (When swiching channel) SETTING ON OFF STEREO 2 AUDIO LINE STEREO MONO ON 3 TURBO OFF ZOOM 4 ZOOM NOMAL ON 5 AUTO POWER ON OFF OFF ON ENGLISH 7 LANGUAGE ESPANOL FRENCH/PORTU OFF 8 HOTEL MODE ON AIR/STD/HRC/IRC 9 CATV AIR/STD/HRC/AFN ON 10 X-RAY OFF ON 11 V-CHIP OFF TV AV 12 AV Option TV AV DVD ON 13 DEMO OFF - Available (South America) - Unavailable (U.S.A) - Unavailable (Canada) - U.S Army - Available (U.S.A, Army) - Unavailable (South America) - Available (U.S.A) - Unavailable - Available - Start Language Select - Nomal - The power is switched on automatically when detaching the Master S/W Auto On - Tact S/W Model - Unavailable - Available REMARK - 800msec Mute Time(Tri-norma) - Unavailable - Zenith stereo (WITH IN UPC1851B) - Line stereo (WITH IN UPC1851B) - Mono (WITH OUT UPC1851B) - Stereo/L STEREO Model - Mono Model - Nornal / Zoom
1
SOUND MUTE 6 (NO SIGNAL)
Samsung Electronics
4-3
Alignment and Adjustments
4-3 Other Adjustments
4-3-1 General
1. Usually, a color TV needs only slight touchup adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. The picture should have good black and white details. There should be no objectionable color shading; if color shading is present, perform the purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isolation transformer.
4-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 30 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
4-4
Samsung Electronics
Alignment and Adjustments
4-3-3 High Voltage Check
CAUTION: There is no high voltage adjustment on this chassis. The B+ power supply must be set to +122.5 volts (Full color bar input and normal picture level).
4-3-6 Purity Adjustment
1. Warm up the receiver for at least 20 minutes. 2. Plug in the CRT deflection yoke and tighten the clamp screw. 3. Plug the convergence yoke into the CRT and set in as shown in Fig. 4-2. 4. Input a black and white signal. 5. Fully demagnetize the receiver by applying an external degaussing coil. 6. Turn the CONTRAST and BRIGHTNESS controls to maximum. 7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to provide vertical green belt. (Fig. 4-3). 8. Tighten the convergence yoke. 9. Slowly move the deflection yoke forward, and adjust for the best overall green screen. 10. Temporarily tighten the deflection yoke. 11. Produce blue and red rasters by adjusting the low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke.
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage should not exceed 30KV. 4. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 30KV under any conditions.
4-3-4 FOCUS Adjustment
1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
4-3-5 Cathode Voltage Adjustment (Screen Adjustment)
1. Connect CRT socket pin GK to an oscilloscope probe. 2. Input a gray scale pattern. (Use a pattern generator, PM5518) 3. Use the P mode key (on the remote control) for the STANDARD picture. 4. Adjust the Screen VR (on the FBT) so that the _ voltage on the oscilloscope becomes 125+2.5V (See Fig. 4-1).
+ 125 _ 2.5V
GND
Fig. 4-1
Samsung Electronics
4-5
Alignment and Adjustments
4 Pole Magnet 6 Pole Magnet Clamper Screw 2 Pole Magnet
2 POLE PURITY
ADJU (VERT
YOKE CLAMP SCREW 6 POLE CONVERGENCE 4 POLE CONVERGENCE
Fig. 4-2 Convergence Magnet Assembly
Vertical Green Belt
31m/m
Fig. 4-3 Center Convergence Adjustment
4-3-7 White Balance Adjustment
(a) Set up 1. Warm up the TV for at least 30 minutes in the Aging Mode (OSD White). This mode is displayed by entering the following sequence: DISPLAY FACTORY FACTORY 2. Input a Toshiba pattern. 2 (b) Low-Light Adjustment 1. Set SBT to 1.2 fL in the Factory Service Mode with using CA100. See Fig. 4-4. Fig. 4-4 2. Adjust RG,BG so that the levels are suitable to each local area. (c) High-Light Adjustment 1. Set SCT to 50FL(13V : 60FL) in the Factory Service Mode with using CA100. See Fig. 4-4 . 4-6 Samsung Electronics
1
Alignment and Adjustments
4-3-8 Center Convergence Adjustment
1. Warm up the receiver for at least 20 minutes. 2. Adjust the two tabs of the 4 pole magnets to change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen. 3. Adjust the Brightness and Contrast controls for a well defined picture. 4. Adjust the two-tab pairs of the 4 pole magnets, and change the angle between them. Superimpose the red and the blue vertical lines in the center area of the screen. 5. Turn the both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal line in the center of the screen. 6. Adjust the two-tab pairs of the 6-pole magnets to superimpose the red and blue line onto the green. (Changing the angle affects the vertical lines, and rotating both magnets affects the horizontal lines.) 7. Repeat adjustments 2~6, if necessary. 8. Since the 4-pole magnets and 6-pole magnets interact, the dot movement is complex (Fig. 4-5).
BLUE
RED
RED/BLUE
GREEN
BLUE RED
RED/BLUE GREEN
4-Pole Magnet Movement
6-Pole Magnet Movement
Fig. 4-5 Center Convergence Adjustment
Samsung Electronics
4-7
Alignment and Adjustments
4-3-9 RF AGC Adjustment
Set the AGC data to 33 (Factory Mode).
4-3-10 Sub-Color Adjustment
Set NSR data to 3 (Factory Mode).
5 5
4-3-11 Geometry Adjustment
SC VSVAVSLHS 1. Input a lion head pattern. 2. Set the SC (S-Correction) as 20(13V : 12) and VS(Vertical Shift) 31 so that the lion head circle becomes oval. 3. Adjust with VA (Vertical Amplitude) so that the top margin of the picture is 4. Fig. 4-9 6. Adjust HS (Horizontal Shift) so that the left and right margins of the picture are 5.
4
Fig. 4-7
4. Adjust with VSL (Vertical-Slope) so that the bottom margin of the picture is 4.
4
Fig. 4-8 5. Adjust with HS (Horizontal Shift) so that the lion-head pattern and CRT centers are aligned.
4-8
Samsung Electronics
Troubleshooting
5. Troubleshooting
5-1 No Power
Counect the Power code
Check the 12.5V-A Line
Normal
Check the 3.3V-A,5V-A Line of IC201S
Normal
Check the X-tal,SDA,SCL port of IC201S
Abnormal
Abnormal Check the FD801S, D807, IC801S or AC-Fuse
Abnormal
Normal
Replace IC201 S
Check/Replace IC802
Check the (33)Pin (H-Drive) of IC201S
Abnormal
Normal
Check the 122.5V- A Line
Abnormal
Normal
Check the FBT,D805(D806)
Check / Replace Q401
Samsung Electronics
5-1
Troubleshooting
5-2 No Video (Sound OK)
Check RK,GK,BK Signal
Abnormal
Check R,G,B Signal into CRT PCB
Nornal
Check IC501 B+(180V-B)
Nornal
Nornal Abnormal Check the Voltage of heater Abnormal Abnormal Check the resistance of R420 Nornal Check/Replace R421,R422,D505 Abnormal Re-Adjust Screen Voltage
Nornal Check CRT and FBT
Replace R420
Abnormal
Check IC201S Pin 51,52,53 (R.G.B) Nornal
Check/Replace D812,FBT
Check/Replace IC201S
Abnormal
Check IC201S Pin 49(BCL-IN) Pin50(IK) Nornal
Check CRT and FBT
5-2
Samsung Electronics
Troubleshooting
5-3 No Sound (Video OK)
Checkthe signal Output from CN603 CN604 Abnormal
Normal
Check Speaker and Wire
Normal Check IC601 Pin1,2,14,15 Abnormal * STEREO Abnormal * MONO Abnormal Check IC601 B+ Normal
Check IC201S Pin28(MIS)
Check IC201S Pin28
Abnormal
Replace IC601
Check IC201S,TUNER
Normal
Normal
Check TUNER
Check R608,R609
Abnormal
Check ICS601 B+/SDA/SCL
Check/Replace IC201S
Normal
Replace/Check IC601
Normal
Check FD801S D807
Abnormal
Check/Replace ICS601
Normal
Replace FD801S,D807
See No Power
Samsung Electronics
5-3
Troubleshooting
5-4 Vertical Lines Appear or Screen
Check IC301 B+ 16V-C,-13.5V-C
Abnormal
Normal
Check R304,R305 D301,D302
Check IC201S Pin 21,22 (VDN,VDP)
Abnormal
Normal Check IC201S Check / Replace IC301
5-4
Samsung Electronics
Exploded View & Parts List
6. Exploded View & Parts List
6-1 TXM1967X/XAA
No Code No Description ;Specification Q'ty Remark
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14
AA64-00152A AA64-70127F AA64-00156B AA61-60003J AA61-40113A
CABINET-FRONT;20F2,BK708P,HIPS,V0,BLK BADGE-BRAND;AL,SS,SILVER,R800 KNOB-POWER;-,20F2,NO-SILK,ABS,HB,BLK SPRING-CS;-,-,SUS304,0.5,OD6,H STOPPER-PCB;-,ABS,HB,NTR. ASSY-PCB,A/V FRONT
1 1 1 1 1 1 2 1 1 1 1 1 1 1 2
F/C BADGE KP SPRING STOPPER
6006-001095 AA65-30018A AA64-00158B AA64-00157B 6002-000512 AA64-00155B 6002-000512 AA96-10141A 6003-001026
SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) CLAMP-WIRE;-,NYLON6.6,-,-,DATL INDICATOR-LED;20F2,ACRYL,CLR, WINDOW-REMOCON;-,20F2,-,PC,VO,VIOLET,SCREW-TAPPING;RH,+,2,M4,L12,ZP KNOB-CONTROL;-,20F2,-,ABS,HB,BLK SCREW-TAPPING;RH,+,2,M4,L12,ZP ASSY-SPEAKER;3W,8OHMX1,700 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
PA+CF CWIRE2 IL WR WR+CF KC KF+CF A/SPK SPK+CF
2 2-1 2-2
AA03-10029W AA27-00200A AA60-10050R
CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT. COIL DEGAUSSING;,1.2MH,10%,30T,1.5OHM,20 SCREW-ASSY;WC,HH,+M5,L31.5,SWR
1 1 4
CRT D-COIL CRT+CF
3 3-1
AA64-00154B 6003-001026
CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
1 4
B/C CB+CF
4
AA96-20129A
ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P,
1
PWR/A
Samsung Electronics
6-1
Exploded View & Parts List
6-2 TXM1997X/XAA
No
Code No
Description
;Specification
Q'ty
Remark
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14
AA64-00152A AA64-70127F AA64-00156B AA61-60003J AA61-40113A
CABINET-FRONT;20F2,BK708P,HIPS,V0,BLK BADGE-BRAND;AL,SS,SILVER,R800 KNOB-POWER;-,20F2,NO-SILK,ABS,HB,BLK SPRING-CS;-,-,SUS304,0.5,OD6,H STOPPER-PCB;-,ABS,HB,NTR. ASSY-PCB,A/V
1 1 1 1 1 1 2 1 1 1 1 1 1 1 2
F/C BADGE KP SPRING STOPPER
6006-001095 AA65-30018A AA64-00158B AA64-00157B 6002-000512 AA64-00155B 6002-000512 3001-001020 6003-001026
SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) CLAMP-WIRE;-,NYLON6.6,-,-,DATL INDICATOR-LED;20F2,ACRYL,CLR, WINDOW-REMOCON;-,20F2,-,PC,VO,VIOLET,SCREW-TAPPING;RH,+,2,M4,L12,ZP KNOB-CONTROL;-,20F2,-,ABS,HB,BLK SCREW-TAPPING;RH,+,2,M4,L12,ZP SPEAKER;3W,8ohm,90dB,140Hz SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
PA+CF CWIRE2 IL WR WR+CF KC KF+CF SPK SPK+CF
2 2-1 2-2 2-3
AA03-10029W AA27-00200A AA60-10050R 3704-001105
CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT. COIL DEGAUSSING;,1.2MH,10%,30T,1.5OHM,20 SCREW-ASSY;WC,HH,+M5,L31.5,SWR SOCKET-CRT;11P,20PI,26.5PI,NI,-
1 1 4 1
CRT D-COIL CRT+CF V999S
3 3-1
AA64-00154B 6003-001026
CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
1 4
B/C CB+CF
4
AA96-20129A
ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P,
1
PWR/AC
6-2
Samsung Electronics
Exploded View & Parts List
6-3 TXM1997X/XAC
No
Code No
Description
;Specification
Q'ty
Remark
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14
AA64-00152A AA64-70127F AA64-00156B AA61-60003J AA61-40113A
CABINET-FRONT;20F2,BK708P,HIPS,V0,BLK BADGE-BRAND;AL,SS,SILVER,R800 KNOB-POWER;-,20F2,NO-SILK,ABS,HB,BLK SPRING-CS;-,-,SUS304,0.5,OD6,H STOPPER-PCB;-,ABS,HB,NTR. ASSY-PCB,A/V FRONT
1 1 1 1 1 1 2 1 1 1 1 1 1 1 2
F/C BADGE KP SPRING STOPPER
6006-001095 AA65-30018A AA64-00158B AA64-00157B 6002-000512 AA64-00155B 6002-000512 3001-001020 6003-001026
SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) CLAMP-WIRE;-,NYLON6.6,-,-,DATL INDICATOR-LED;20F2,ACRYL,CLR, WINDOW-REMOCON;-,20F2,-,PC,VO,VIOLET,SCREW-TAPPING;RH,+,2,M4,L12,ZP KNOB-CONTROL;-,20F2,-,ABS,HB,BLK SCREW-TAPPING;RH,+,2,M4,L12,ZP SPEAKER;3W,8ohm,90dB,140Hz SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
PA+CF CWIRE2 IL WR WR+CF KC KF+CF SPK SPK+CF
2 2-1 2-2 2-3
AA03-10029W AA27-00200A AA60-10050R 3704-001105
CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT. COIL DEGAUSSING;,1.2MH,10%,30T,1.5OHM,20 SCREW-ASSY;WC,HH,+M5,L31.5,SWR SOCKET-CRT;11P,20PI,26.5PI,NI,-
1 1 4 1
CRT D-COIL CRT+CF V999S
3 3-1
AA64-00154B 6003-001026
CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
1 4
B/C CB+CF
4
AA96-20129A
ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P,
1
PWR/AC
Samsung Electronics
6-3
Exploded View & Parts List
6-4 TXM1367X/XAA
No
Code No
Description
;Specification
Q'ty
Remark
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13
AA64-00162A AA64-70127F AA64-00165B AA61-60003J
CABINET-FRONT;14F2,BK708P,HIPS,V0,BLK BADGE-BRAND;AL,SS,SILVER,R800 KNOB-POWER;14F2,NO-SILK,ABS,HB,BLK SPRING-CS;-,-,SUS304,0.5,OD6,H ASSY-PCB,A/V FRONT
1 1 1 1 1 2 1 1 1 1 2 1 1 1
F/C BADGE KP SPRING
6006-001095 AA65-30105A AA61-40113A AA64-00167B AA64-00166B 6002-000512 AA64-00164B
SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) CLAMP-WIRE;NYLON 66N,VO,NTR,15MM STOPPER-PCB;-,ABS,HB,NTR. INDICATOR-LED;14F2,ACRYL,CLR, WINDOW-REMOCON;14F2,PC,VIOLET SCREW-TAPPING;RH,+,2,M4,L12,ZP KNOB-CONTROL;14F2,ABS,HB,BLK SCREW-TAPPING;RH,+,2,M4,L12,ZP
PA+CF CWIRFC STTOPER INLED WINDOW WR+CF KC
AA96-10014A
ASSY-SPEAKER;8OHM,2.5W,3(2),F/200
A/SPK
2 2-1 2-2
AA03-10002M 6006-001095 3704-001089
CRT-COLOR;-,A34KQV42X,0MG,14, SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) SOCKET CRT;9P,22.5PI,12PI,SN,13
1 2 1
CRT CRT+CF V999S
3 3-1
AA64-00259A 6003-001026
CABINET-BACK;-,14F2,-,HIPS,V0,BLK. SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
1 4
B/C CB+CF
4
AA96-20129C
ASSY-POWER,CORD;-,EP2/YES,H/C200,ME301P,
1
PWR/AC
6-4
Samsung Electronics
Exploded View & Parts List
6-5 TXM1367X/XAC
No
Code No
Description
;Specification
Q'ty
Remark
1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13
AA64-00162A AA64-70127F AA64-00165B AA61-60003J
CABINET-FRONT;14F2,BK708P,HIPS,V0,BLK BADGE-BRAND;AL,SS,SILVER,R800 KNOB-POWER;14F2,NO-SILK,ABS,HB,BLK SPRING-CS;-,-,SUS304,0.5,OD6,H ASSY-PCB,A/V FRONT
1 1 1 1 1 2 1 1 1 1 1 1 1 1
F/C BADGE KP SPRING
6006-001095 AA65-30105A AA61-40113A AA64-00167B AA64-00166B 6002-000512 AA64-00164B
SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) CLAMP-WIRE;NYLON 66N,VO,NTR,15MM STOPPER-PCB;-,ABS,HB,NTR. INDICATOR-LED;14F2,ACRYL,CLR, WINDOW-REMOCON;14F2,PC,VIOLET SCREW-TAPPING;RH,+,2,M4,L12,ZP KNOB-CONTROL;14F2,ABS,HB,BLK SCREW-TAPPING;RH,+,2,M4,L12,ZP
PA+CF CWIRFC STTOPER INLED WINDOW WR+CF KC
AA96-10014A
ASSY-SPEAKER;8OHM,2.5W,3(2),F/200
A/SPK
2 2-1 2-2
AA03-10002M AA60-10050Q 3704-001089
CRT-COLOR;-,A34KQV42X,0MG,14, SCREW-ASSY;WC,HH,M5,L26.5,SWRCH, SOCKET CRT;9P,22.5PI,12PI,SN,13
1 4 1
CRT CRT+CF V999S
3 3-1
AA64-00259A 6003-001026
CABINET-BACK;-,14F2,-,HIPS,V0,BLK. SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
1 4
B/C CB+CF
4
AA96-20129C
ASSY-POWER,CORD;-,EP2/YES,H/C200,ME301P,
1
PWR/AC
Samsung Electronics
6-5
Electrical Parts List
7. Electrical Parts List
7-1 TXM1967X/XAA
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-CHASSIS
1 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ....4 ....4 ....4 ....4 ...3 ....4 ....4 ....4 ....4 ...3 ....4 ....4 ....4 ...3 ...3 ....4 ....4 ....4 ...3 ....4 ....4 ....4 ....4 ...3 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 A/CHASSI AA91-04207A ASSY-CHASSIS;K15D,19,USA AC+BC CLW/HS CWIRE2 FBT A/MAIN Q401 PC801S IC902 CX801S CR401S SF101S SWN01 FP801S V999S CN704 JA701 IC201S T801S T444S T401 LR401S LX801S RM901 CN501 TU01S IC301 AA65-30008A AA65-30018A AA65-30018A AA65-30018A AA94-08282F 0502-001115 0604-001038 1103-001209 2306-000318 2303-001015 2904-001221 3404-000295 3601-000144 3704-001105 3711-002646 3722-000162 AA09-00295A AA26-00172A AA26-00065A AA26-50001B AA27-00053A AA29-30001D AA32-00015A AA39-20620B AA40-00073A AA96-00244A 0205-000129 1204-001483 6003-000335 AA62-00046A AA96-00244D 0205-000129 1201-001600 6003-000335 AA62-00046A AA96-00245A 1203-001939 6003-000334 AA62-00055A AA96-00555A AA96-50311A 1201-001159 6003-000334 AA62-30175D AA96-50395F 0205-000129 1203-002466 6003-000334 AA62-30190A AA97-07230G 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000006 0402-000132 0402-000132 0402-000254 0402-000254 0402-000493 0402-000534 0402-000540 0402-001105 CLAMP-CORD;-,PE,HB,BLK,-,CLAMP-WIRE;-,NYLON6.6,-,-,DATL CLAMP-WIRE;-,NYLON6.6,-,-,DATL CLAMP-WIRE;-,NYLON6.6,-,-,DATL ASSY PCB MAIN;TXM1966,K15D,SAMEX TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8 PHOTOCOUPLER;TR,130-260%,200MW IC-EEPROM;AT24C04-PC27 C,512Kx8Bit,DIP,8 C-FILM,MPPF;220NF,20%,250V,-,2 C-FILM,PPFF;5.5NF,5%,1.6KV,TP, FILTER-SAW AV,45.75MHz,SIP5K,ST,14.2dB,M SW-TACT,V;KPT1122R1KEYSTT=0.3M FUSE-FERRULE;125V,4A,SLOWBLOW, SOCKET-CRT;11P,20PI,26.5PI,NI,POST-HEADER;67094-007(AUTO) JACK-PIN;2P,3.4MM,-,SN IC MICOM;TDA9377PS/N2/AI,SPM-458AN,64P,3 RANS-SWITCHING;EER3543,K15D,90~264,PM2A TRANS FBT;-,FSV-14A004C(S),14-22,125V HORIZ.DRIVE;-,7.1MH,102UH,10-2 COIL-LINEARLITY;-,193uH,DR10X10 C:4.35,7 FILTER-LINE;-,6.0MH,2A,-,SQ191 MODULE-REMOCON;FRP-3521H31,38KHZ,940MM,M LEAD-CONNECTOR;ASSY,9P,YBNH250-09,S,400m TUNER-TECC1040PG32A(S),181CH,45.75MHZ,75 ASSY H/S;-,-,AA62-00046A,LA7840,GREASE-SILICON;SC102,JAPAN IC-VERTICAL PROCESSO;LA7840,SIP,7P,708MI SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR HEAT SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X ASSY H/S;-,SOUND,AA62-00046A,TDA7266M,GREASE-SILICON;SC102,JAPAN IC-AUDIO AMP;7266,ZSIP,15P,-,SINGLE,26dB SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR HEAT SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X ASSY H/S;-,-,AA62-00055A,KA7632,IC-POSI.FIXED REG.;7632,SIP,10P,-,PLASTI SCREW-TAPTITE;RH,+,2S,M3,L6,ZP HEAT SINK-PS;-,-,T1.0,-,35*15*25,D1,-,-, ASSY LED GUIDE;-,-,UEX-LD-030,GREEN ASSY-H/S;-,VIDEO,AA62-30175D,TDA6107Q,ICVIDEOAMP;TDA6107Q,ZIP,9P,300 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP HEATSINK-PS;-,SECC,T1.0,-,33X15X30FT-2 ASSY H/S;-,POWER,AA62-30190A,5Q0740RT GREASE-SILICON;SC102,JAPAN IC-PWM CONTROLLER;KA5Q0740RT,TO220F-5L,5 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP -,SECC-CA,T1.0,-,-,-,Cr03 A ASSY AUTO-MAIN;,K15D,SAMEX DIODE;1N4148,100V,300mA,,1V,8nS,TAPING DIODE;1N4148,100V,300mA,,1V,8nS,TAPING DIODE;1N4148,100V,300mA,,1V,8nS,TAPING DIODE;1N4148,100V,300mA,,1V,8nS,TAPING DIODE;1N4148,100V,300mA,,1V,8nS,TAPING DIODE;1N4148,100V,300mA,,1V,8nS,TAPING DIODE-SWITCHING;BAV21,250MA,400MW,50NS,2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;RGP10J,600V,1A,DO-41 DIODE-RECTIFIER;RGP10J,600V,1A,DO-41 DIODE-RECTIFIER;1R5GU41,400V,1 DIODE-RECTIFIER;RG10V,400V,1.5 DIODE-RECTIFIER;RU20A,600V,1.5 DIODE-RECTIFIER;ERB43-04SV1,40
IC601
IC802
LD901 IC501
IC801S
A/AUTO D201 D601 D804 D808 D811 DR003S D803 D303 D809 D501 DR001S D807 D302 D805 D301
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
D304 D401 D502 D503 D504 D812 D801S D802S D803S D804S DR002S DZ211 DZ401 DZ402 DZ903 DZ904 DZ905 DZ803 DZ101 DZ303 DZ604 DZ201 DZ202 DZ205 DZ306 DZ307 DZ501 DZ502 DZ503 DZ504 DZ806 DZ807 DZ808 DZ801 DZ204 DZ302 DZ802 DZ901 DZ805 DZ301 DZ305 Q201 Q901 QR001S Q402 Q202 Q601 Q802 IC802 R207 R905 R906 R206 R301 R843 R409 R823 R808 R902 R904 R287 R211 R233 R501 R502 R506 R510
0402-001105 0402-001105 0402-001105 0402-001105 0402-001105 0402-001105 0402-001111 0402-001111 0402-001111 0402-001111 0402-001111 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000699 0403-000700 0403-000700 0403-000719 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-000720 0403-001140 0403-001211 0403-001221 0403-001318 0403-001373 0403-001327 0403-001328 0403-001328 0501-000283 0501-000283 0501-000283 0501-000369 0501-002183 0501-002183 0501-002183 1203-001217 2001-000005 2001-000005 2001-000005 2001-000010 2001-000016 2001-000019 2001-000022 2001-000037 2001-000109 2001-000241 2001-000241 2001-000273 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281
DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 DIODE-RECTIFIER;ERB43-04SV1,40 AB01-19ACTIFIER;1N5397GP,600V,1.5A,DO-20 AB01-19ACTIFIER;1N5397GP,600V,1.5A,DO-20 AB01-19ACTIFIER;1N5397GP,600V,1.5A,DO-20 AB01-19ACTIFIER;1N5397GP,600V,1.5A,DO-20 AB01-19ACTIFIER;1N5397GP,600V,1.5A,DO-20 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;TZP27B,27V,27-30.8 DIODE-ZENER;TZP33A,33V,31-35V, DIODE-ZENER;TZP33A,33V,31-35V, DIODE-ZENER;MTZJ7.5B,7.5V,7.07-7.45V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;RD10ESAB-T4,10V,9.19-10.30V, DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,D DIODE-ZENER;MTZJ4.3B,4.17-4.43V,500mW,DO DIODE-ZENER;MTZJ5.1A,4.81V-5.07V,500mW,D DIODE-ZENER;MTZJ18A,16.22-17.06V,500mW,D DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D TRANSISTOR;KSA539-Y(TAPG)/YTAM TRANSISTOR;KSA539-Y(TAPG)/YTAM TRANSISTOR;KSA539-Y(TAPG)/YTAM TRANSISTOR;KSC2331-Y(TAPG) TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100 IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P R-CARBON;390OHM,5%,1/8W,AA,TP, R-CARBON;390OHM,5%,1/8W,AA,TP, R-CARBON;390OHM,5%,1/8W,AA,TP, R-CARBON;68Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON(S);1OHM,5%,1/2W,AA,TP R-CARBON(S);10ohm,5%,1/2W,AA,TP,2.4x6.4m R-CARBON(S);33OHM,5%,1/2W,AA,T R-CARBON(S);330OHM,5%,1/2W,AA, R-CARBON(S);470OHM,5%,1/2W,AA, R-CARBON;1.5KOHM,5%,1/8W,AA,TP R-CARBON;1.5KOHM,5%,1/8W,AA,TP R-CARBON;100KOHM,5%,1/8W,AA,TP R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP,
Samsung Electronics
7-1
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
R511 R512 R909 R911 R912 R913 R914 R917 R933 R934 R942 R943 R291A R601 R612 R807 R828 R910 R606 R224 R225 R205 RR005S R218 RR002S R602 R604 R926 R944 R918 R940 R941 R220 R901 R903 R907 R908 R607 R214 R829 R208 RR001S R202 R830 R925 R708 R227 R228 R109 R927 R207 R110 R915 R108 R222 R605 R212 R215 R610 R408 R504 R414 R832 R819 R820 R303 R840 R411 R821 R809 R810 R818 R805 R405 R831 R501H R502H
2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000281 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000325 2001-000397 2001-000397 2001-000411 2001-000411 2001-000429 2001-000429 2001-000429 2001-000429 2001-000449 2001-000449 2001-000449 2001-000472 2001-000472 2001-000472 2001-000472 2001-000472 2001-000472 2001-000490 2001-000563 2001-000591 2001-000660 2001-000689 2001-000734 2001-000734 2001-000734 2001-000739 2001-000739 2001-000786 2001-000793 2001-000857 2001-000924 2001-000924 2001-000947 2001-000947 2001-000947 2001-000969 2001-000969 2001-000969 2001-001037 2001-001062 2001-001078 2001-001088 2001-001088 2001-001088 2003-002238 2001-001108 2001-001114 2001-001131 2001-001150 2001-001150 2001-001154 2001-001170 2001-001187 2001-001192 2002-001008 2002-001008
R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;100OHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;10KOHM,5%,1/8W,AA,TP, R-CARBON;120OHM,5%,1/8W,AA,TP, R-CARBON;180KOHM,5%,1/8W,AA,TP R-CARBON;180KOHM,5%,1/8W,AA,TP R-CARBON;18KOHM,5%,1/8W,AA,TP, R-CARBON;18KOHM,5%,1/8W,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.2KOHM,5%,1/8W,AA,TP R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;2.7KOHM,5%,1/8W,AA,TP R-CARBON;200OHM,5%,1/8W,AA,TP, R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;3.3KOHM,5%,1/8W,AA,TP R-CARBON;33KOHM,5%,1/8W,AA,TP, R-CARBON;390KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7KOHM,5%,1/8W,AA,TP R-CARBON;4.7MOHM,5%,1/8W,AA,TP R-CARBON;4.7MOHM,5%,1/8W,AA,TP R-CARBON;47KOHM,5%,1/8W,AA,TP, R-CARBON;47OHM,5%,1/8W,AA,TP,1 R-CARBON;560OHM,5%,1/8W,AA,TP, R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;7.5KOHM,5%,1/8W,AA,TP R-CARBON;7.5KOHM,5%,1/8W,AA,TP R-CARBON;7.5KOHM,5%,1/8W,AA,TP R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON;75OHM,5%,1/8W,AA,TP,1 R-CARBON(S);0.39OHM,5%,1/2W,AA R-CARBON(S);10MOHM,5%,1/2W,AA, R-CARBON(S);15KOHM,5%,1/2W,AA, R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 R-METAL OXIDE(S)1.3OHM,5%2W,AF,TP,3.9X10 R-CARBON(S);22KOHM,5%,1/2W,AA, R-CARBON(S);270OHM,5%,1/2W,AA, R-CARBON(S);33KOHM,5%,1/2W,AA, R-CARBON(S);470KOHM,5%,1/2W,AA R-CARBON(S);470KOHM,5%,1/2W,AA R-CARBON(S);5.1KOHM,5%,1/2W,AB R-CARBON(S);6.8OHM,5%,1/2W,AB, R-CARBON(S);75OHM,5%,1/2W,AA,T R-CARBON(S);820OHM,5%,1/2W,AB, R-COMPOSITION;1.8KOHM,10%1/2W,AA,TP,3.7 R-COMPOSITION;1.8KOHM,10%1/2W,AA,TP,3.7
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
R503 RP801S RY801S R402 R316 R413 R403 R827 R7407 R803 R804 R603 R423 R817 RR003S R424 R219 R822 RR004S R302 R306 R304 R305 R801 R825 R608 R609 R824 R422 R421 R420 C806A C501 C302 C816 CR409S C908 C909 C408 CR404S C503 C811 C105 C111 C912 C223 C224 C602 C906 C505 C226 C211 C502 C109 C804 C810 C309 C227 C604 C217 C234 C805 C407 C248 C232 C420 C312 C301 C215 C216 C233 CR405S C916 C103 C207 C208
2002-001008 2002-001010 2002-001013 2003-002178 2003-000652 2003-000664 2003-002173 2003-001023 2003-001040 2003-002102 2003-002102 2004-000195 2004-001373 2004-001377 2004-001376 2004-001402 2004-001914 2004-001983 2004-004048 2004-001371 2004-001371 2008-000253 2008-000253 2008-001107 2008-000266 2008-000284 2008-000284 2008-000294 2008-001011 2008-001011 2008-001047 2201-000108 2201-000193 2201-000259 2201-000375 2201-002028 2201-000573 2201-000573 2201-000573 2201-000599 2201-000639 2201-000723 2201-000991 2202-000127 2202-000127 2202-000127 2202-000796 2202-000796 2202-000796 2202-000796 2202-000106 2202-000829 2202-002037 2301-000213 2301-000224 2301-000224 2301-000224 2301-000254 2301-000301 2301-000301 2301-000342 2301-000342 2301-000342 2301-000383 2301-000445 2301-000445 2301-001065 2305-000149 2305-000285 2305-000289 2305-000289 2305-000289 2305-000382 2305-000411 2305-000665 2305-000665 2305-000665
R-COMPOSITION;1.8KOHM,10%1/2W,AA,TP,3.7 R-COMPOSITION;1.8MOHM,5%,1/2W,AA,TP,3.7X R-COMPOSITION;4.7MOhm,5%,1/2W,AA,TP,3.7X R-METAL OXIDE(S) 1Kohm,5%,2W,AG,TP,3.9X1 R-METAL OXIDE(S);330ohm,5%,2W,AF,TP,4x12 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M R-METAL OXIDE(S);7.5Kohm,5%,2W,AG,TP,3.9 R-METALOXIDE(S);120OHM,5%,2W,A R-METALOXIDE(S);47Kohm,5%,2W,AF,TP,3.9x1 R-METAL OXIDE;68Kohm,5%,2W,AF,TP,4x12mm R-METAL OXIDE;68Kohm,5%,2W,AF,TP,4x12mm R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m R-METAL,FILM;RM1/2T100K-F R-METAL(S);120KOHM,1%,1/2W,AA,TP,2.4X6.4 R-METAL(S);11KOHM,1%,1/2W,AA,T R-METAL(S);6.8KOHM,1%,1/2W,AA, R-METAL;39KOHM,2%,1/8W,AA,TP,1 R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4 R-METAL(S);3.9Kohm,1%,1/2W,AA,TP,2.5x6.5 R-METAL(S);1.5KOHM,1%,1/2W,AA, R-METAL(S);1.5KOHM,1%,1/2W,AA, R-FUSIBLE(S);0.47OHM,5%,1W,AF, R-FUSIBLE(S);0.47OHM,5%,1W,AF, R-FUSIBLE(S);300ohm,5%,2W,AG,TP,3.9x12mm R-FUSIBLE(S);1OHM,5%,2W,AF,TP, R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M R-FUSIBLE;33OHM,5%,2W,AF,TP,3. R-FUSIBLE(S);0.18OHM,10%,2W,AF R-FUSIBLE(S);0.18OHM,10%,2W,AF R-FUSIBLE(S);68ohm,5%,2W,AF,TP,3.9x10mm C-CERAMIC,DISC;1.5NF,10%,1KV,Y C-CERAMIC,DISC;10PF,0.25PF,50V C-CERAMIC,DISC;180PF,10%,500V,Y5P,6X4MM, C-CERAMIC,DISC;220PF,5%,50V,RH C-CERAMIC,DISC;0.47nF,10%,2kV,Y5P,TP,7.5 C-CERAMIC,DISC;47PF,5%,50V,NPO C-CERAMIC,DISC;47PF,5%,50V,NPO C-CERAMIC,DISC;47PF,5%,50V,NPO C-CERAMIC,DISC;560PF,10%,500V, C-CERAMIC,DISC;680PF,10%,2KV,Y5P,-,5MM,T C-CERAMIC,DISC;4.7nF,20%,3KV,Y5U,TP,16x5 C-CERAMIC,HIC;CK45(T)B2KV561-K C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;10NF,+80-2 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1NF,10%,50 C-CERAMIC,MLC-AXIAL;1.5nF,20%,16V,Y5P,TP C-CERAMIC,MLC-AXIAL;820pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;100NF,+80-20 C-FILM,PEF;220NF,5%,250V,21.5X C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM,PEF;22NF,5%,50V,7.4X3.9 C-FILM,PEF;39NF,5%,50V,7.5X3.5X6.5MM,5MM C-FILM,PEF;6.8NF,5%,50V,6.5X4. C-FILM,PEF;6.8NF,5%,50V,6.5X5. C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x11mm, C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x12mm, C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm, C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,4mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,MPPF;47NF,55,630V,TP,19 C-FILM;CF922N100VT104-J-40/105 C-FILM,MPEF;220NF,5%,100V,-,5M C-FILM,MPEF;220NF,5%,63V,-,3MM C-FILM,MPEF;220NF,5%,63V,-,4MM C-FILM,MPEF;220NF,5%,63V,-,5MM C-FILM,MPEF;4.7NF,5%,400V,TP,-,5MM. C-FILM,MPEF;470NF,5%,50V,7.3X4 C-FILM;104J, 60V,5MM TAPING C-FILM;104J, 60V,4MM TAPING C-FILM;104J, 60V,3MM TAPING
7-2
Samsung Electronics
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
C210 C218 C222 C230 C803 C819 C913 C920 C225 C812 C817 C821 C823 C307 C308 C506 CR01S CR02S CE01 C403 C219 C601 C603 C221 C212 C827 C110 C802 C504 C304 C306 C209 C213 C229 C903 C910 C605 C203 C206 C220 C231 C820 C813 C101 C406 C808 L103 L202 L903 R101 R102 L203 L301 L302 L404 L102 L201 L230 L405 L902 L904 L804 L807 X901 L808 L806 L802 L803 J127 SW901 SW902 SW903 SW904 SW905 FD801S F801A F801B
2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2305-000665 2309-000138 2401-000262 2401-000302 2401-000302 2401-000302 2401-000360 2401-000360 2401-000430 2401-000480 2401-000480 2401-000480 2401-000560 2401-000603 2401-000603 2401-000603 2401-000660 2401-000660 2401-000927 2401-000962 2401-001192 2401-001232 2401-001397 2401-002288 2401-001840 2401-001840 2401-001840 2401-001840 2401-001840 2401-001998 2401-002235 2401-002235 2401-002235 2401-002235 2401-002235 2401-002290 2401-002594 2401-002619 2401-003028 2701-000114 2701-000114 2701-000114 2701-000114 2701-000114 2701-000127 2701-000142 2701-000142 2701-000142 2701-000159 2701-000159 2701-000159 2701-000159 2701-000177 2701-000177 2701-001030 2701-001030 2801-003433 2901-000297 3301-000287 3301-000287 3301-000287 3301-000287 3404-000244 3404-000244 3404-000244 3404-000244 3404-000244 3601-001086 3602-000114 3602-000114
C-FILM;104J, 60V,2MM TAPING C-FILM;104J, 60V,1MM TAPING C-FILM;104J, 60V,0MM TAPING C-FILM;104J, 60V,1MM TAPING C-FILM;104J, 60V,2MM TAPING C-FILM;104J, 60V,3MM TAPING C-FILM;104J, 60V,4MM TAPING C-FILM;104J, 60V,5MM TAPING C-FILM,PE-PPF;100NF,5%,50V,TP, C-AL;100UF,20%,160V,GP,16X25MM,5MM, C-AL;100UF,20%,25V,GP,6X11MM,3 C-AL;100UF,20%,25V,GP,6X11MM,4 C-AL;100UF,20%,25V,GP,6X11MM,5 C-AL;100UF,20%,50V,GP,8X11MM,4 C-AL;100UF,20%,50V,GP,8X11MM,5 C-ELECTROLYTIC;CE04WTAPG250V10 C-AL;10UF,20%,50V,GP,5X11MM,4M C-AL;10UF,20%,50V,GP,5X11MM,5M C-AL;10UF,20%,50V,GP,5X11MM,5M .-AL;1UF,20%,160V,GP,GT,6.3,11MM C-AL;1UF,20%,50V,GP,5X11MM,3MM C-AL;1UF,20%,50V,GP,5X11MM,4MM C-AL;1UF,20%,50V,GP,5X11MM,5MM C-ELECTROLYTIC;CE04WTAPG50V2.1 C-ELECTROLYTIC;CE04WTAPG50V2.2 C-AL;22UF,20%,250V,GP,13X20MM, C-AL;22uF,20%,50V,GP,TP,5x11,5 C-AL;33UF,20%,50V,GP,6X11MM,5MM,TP C-AL;4.7UF,20%,250V,GP,10X12.5 C-AL;470UF,20%,25V,GP,10X16MM, C-ELEC;CE04-55/10525VT471-MWRG C-AL;100UF,20%,16V,GP,TP,6.3X3 C-AL;100UF,20%,16V,GP,TP,6.3X2 C-AL;100UF,20%,16V,GP,TP,6.3X1 C-AL;100UF,20%,16V,GP,TP,6.3X0 C-AL;100UF,20%,16V,GP,TP,6.3X1 C-AL;1000UF,20%,25V,GP,TP,10X20 C-ELECTROLYTIC;CE04W(T)16V7M C-ELECTROLYTIC;CE04W(T)16V8M C-ELECTROLYTIC;CE04W(T)16V9M C-ELECTROLYTIC;CE04W(T)16V10M C-ELECTROLYTIC;CE04W(T)16V10M C-AL;47uF,20%,160V,GP,TP,13x20,5 C-AL;220uF,20%,16V,GP,TP,8x11.5,5 C-AL;47uF,20%,25V,GP,TP,5x11,5 C-AL;100UF,20%,25V,GP,TP,6.3X1 NDUCTOR-AXIAL;10UH,10%,2.5X1. NDUCTOR-AXIAL;10UH,10%,2.5X0. NDUCTOR-AXIAL;10UH,10%,2.5X1. NDUCTOR-AXIAL;10UH,10%,2.5X2. NDUCTOR-AXIAL;10UH,10%,2.5X3. NDUCTOR-AXIAL;15UH,10%,2.5X3. INDUCTOR-AXIAL;1UH,10%,2.5X3.4 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 INDUCTORAXIAL;22uH,10%,4.2x9.8mm INDUCTORAXIAL;22uH,10%,4.2x9.8mm INDUCTORAXIAL;22uH,10%,4.2x9.8mm INDUCTORAXIAL;22uH,10%,4.2x9.9mm INDUCTOR-AXIAL;33UH,10%,2.5X3.4MM INDUCTOR-AXIAL;33UH,10%,2.5X3.4MM INDUCTOR-AXIAL;43uH,10%,14x4.5mm INDUCTOR-AXIAL;43uH,10%,14x4.5mm CRYSTAL-UNIT;12MHZ,30PPM,28-AAM,30PF,30O FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITEBEAD;AA,3.5X1.0X6. CORE-FERRITEBEAD;AA,3.5X1.0X6. CORE-FERRITEBEAD;AA,3.5X1.0X6. CORE-FERRITEBEAD;AA,3.5X1.0X6. WITCH-TACT;15V,20MA,90-170GF, SWITCH-TACT;15V,20MA,90-170GF, SWITCH-TACT;15V,20MA,90-170GF, SWITCH-TACT;15V,20MA,90-170GF, SWITCH-TACT;15V,20MA,90-170GF, FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS FUSE-HOLDER;-,-,30MOHM FUSE-HOLDER;-,-,30MOHM
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
DZ804 J101 J102 J103 J104 J105 J106 J107 J108 J110 J111 J112 J113 J114 J115 J117 J120 J121 J122 J123 J124 J128 J129 J130 J131 J132 J135 J137 J138 J139 J140 J142 J150 J401 J604 J605 J6060 J8001 J802 J803 J804 J806 J807 J808 JAW02 L403 R229 R309 R507 R508 R509 R850 R822 J125 L805 J601 J811 L206 00VER EY401 EY402 EY403 EY404 EY405 EY414 EY415 EY416 EY417 EY418 EY419 EY420 EY421 EY501 EY819 EY827 EY829 EY833
3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 AA41-00625A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A
WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A WIRE-SO,COPPER;TA0.6SN/52M/M(A PCB-MAIN;CT2188,FR-1,1L,A,1.6T,245X245,K EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST
Samsung Electronics
7-3
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ...3 ....4 ....4 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
EY701 EY702 EL401 EL402 EL801 EL802 GT301 GT302 GT401 GT402 GT501 GT801 GT802 GT803 GT804 GT805 Z201 RE01 RE02 C915 R505 CR403S C815 PWR/A
C801 NT801S CY801S JA703 JE601 CN702A CN603 P803S
AA60-40011A AA60-40011A AA60-40011B AA60-40011B AA60-40011B AA60-40011B AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A 2903-000129 2001-000117 2001-000117 2401-002009 2008-000264 2306-000179 2401-000703 AA96-20129A AA39-10007Y AA61-20284A 0204-000442 0202-000008 0204-001024 0202-000187 2401-000822 1404-001045 2201-002002 3722-000184 3722-000143 AA39-20070D 3711-002642 1404-001247
EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.0,OD2.8,-,-,BST EYELET;-,ID2.2,OD3.2,-,-,BSP EYELET;-,ID2.2,OD3.2,-,-,BSP EYELET;-,ID2.2,OD3.2,-,-,BSP EYELET;-,ID2.2,OD3.2,-,-,BSP PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO FILTER-CERAMIC;BR,4.5MHz,-,-,-,TP,R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m C-AL;100UF,20%,16V,GP,TP,6.3X7 R-FUSIBLE(S);1OHM,5%,1W,AF,TP, C-FILM,MPPF;300nF,5%,250V,TP,20x18.5x10. C-ELEC;CE04-40/8525VT222-MWSD ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P, POWER-CORD;-,EP2/YES,SPT-2 18AWGx2C,2.4m HOLDER P CORD;PP,VO,BLK,KE-002 SOLVENT;CH3-CH5H-CH396%IM-1000 SOLDER-WIRE;S63S-D3.0,S63A,D3,63/37 FLUX;DF-96TVS,-,20%,SOLDER-WIREFLUX;-,RS60S,D1.2,6 C-ELECTROLYTIC;CE04W200V220U-H THERMISTOR NTC;4.7OHM,15%,2900K,35.0MW,T C-CERAMIC,DISC;4700PF,20%,400V JACK-RCA;2P,3.4MM,-,AG JACK-PHONE;1P,3.4MM,-,MBAG LEAD-CONNECTOR,ASSY;-,YBNH025-07,67096-0 POST-HEADER;67094-003(AUTO) THERMISTOR-PTC;1.5OHM;+30/-20,110V,140VA
..2 AC+BC ..2 FBT
AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL
ASSY-CPT
1 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 A/CPT CRT+DCOI CRT C-Y D-COIL D-Y SPACER A/TBC CDCOIL TAPE-DY AA91-04393A ASSY-CPT;A48KRD82X(H),+380MG,SEMI-TINT 0203-001160 TAPE FILAMENT SCOTCH#8915,T0.16,W24,L0.1 AA03-10029W CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT. AA27-00002A MAGNET-CONVERGENCE;JH291-SC-OB,29.1M AA27-00200A COIL DEGAUSSING;,1.2MH,10%,30T,1.5OHM,20 AA27-50004W DEFL-YOKE;-,DSE-1992LL(1H),20'/A48KRD82X AA63-60028A SPACER-DY;-,NEOPRENE,-,BLK,V0W AA98-70014B ASSY-TBC,WIRE;20,NTSC,1P AA61-00734A HOLDER;25POLYVINYL,DEGAUSSING,CHLORI 0203-001303 TAPE-ACETATE;#1554,T0.25,W19,L30000,WHT
ASSY BOX
1 ..2 ..2 A/BOX BOX PCK AA92-02113A ASSY BOX;TXJ1996MHX/XAA AA68-01542A LABEL;(UNIBOX),PAPER WHT ALLMD AA69-00415A PACKING-CASE;CBDW,KRFT-LNR,275,20R1
MANUAL USERS
1 I/B AA68-02340A MANUAL USERS;,ENG,USA,W/P100(G),B5,K15D,
ASSY LABEL
1 ..2 ..2 ..2 A/LABEL L/RAT L/CRT L/SET AA92-02390A ASSY LABEL;TXJ1996MHX/XAA AA68-02371A LABEL-RATING;ART-PAPER,90(S),SEA AA68-01557A LABEL ENERGY;STAR,STATIC FREE FILM AA68-01568A LABEL;SET,A48KRD82X,SAMS.23-28KV
ASSY-COVER;FRONT
1 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ..2 A/CFRN SPK+CF PA+CF S/CRT CRT+CF STOPPER F/C KF+CF WR+CF SPRING KC KP WR IL BADGE CWFC L/IND L/QMS L/WARN A/SPK SPK L/SPK CWIRE2 AA90-03255A ASSY-COVER;FRONT;K15D,19,USA 6003-001026 6006-001095 AA60-00038A AA60-10050R AA61-40113A AA64-00152A 6002-000512 6002-000512 AA61-60003J AA64-00155B AA64-00156B AA64-00157B AA64-00158B AA64-70127F AA65-30105A AA68-00524A AA68-02391A AA68-01618A AA96-10141A 3001-001020 AA39-20501C AA65-30018A SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) SPACER-CRT;PS,SHEET,T1.0,BLK,OD22,ID10. SCREW-ASSY;WC,HH,+M5,L31.5,SWR STOPPER-PCB;-,ABS,HB,NTR. CABINET-FRONT;20F2,BK708P,HIPS,V0,BLK SCREW-TAPPING;RH,+,2,M4,L12,ZP SCREW-TAPPING;RH,+,2,M4,L12,ZP SPRING-CS;-,-,SUS304,0.5,OD6,H KNOB-CONTROL;-,20F2,-,ABS,HB,BLK KNOB-POWER;-,20F2,NO-SILK,ABS,HB,BLK WINDOW-REMOCON;-,20F2,-,PC,VO,VIOLET,INDICATOR-LED;20F2,ACRYL,CLR, BADGE-BRAND;AL,SS,SILVER,R800 CLAMP-WIRE;NYLON 66N,VO,NTR,15MM LABEL-INDICATOR;A/P 90(G),CXJ1352X/XAA,U LABEL-QMS;ART-PAPER(90)G,110x24mm LABEL-WARNING;WHTPAPER100 ASSY-SPEAKER;3W,8OHMX1,700 SPEAKER;3W,8ohm,90dB,140Hz LEAD CONNECTOR-ASSY;-,67096-003,REC,3(2) CLAMP-WIRE;-,NYLON6.6,-,-,DATL
ASSY P/MATERIAL
1 ..2 ..2 ..2 ..2 A/PACK BXTAPE STAPLE C/SET PE-BAG AA92-02667A ASSY P/MATERIAL;TXJ1996MHX/XAA 0203-001295 AA60-40006A AA69-01637A AA69-01192A TAPE-OPP MASKING;1242,T0.06,W100,L91.4M, PIN-STAPLE;-,-,-,H18,33X17.8X2 CUSHION-SET;20R1/F2NEW,(SAMEX),EPS,C=0.0 BAG PE;CT20S1BZ,19-20COM,W40',H48,2
ASSY-ACCESSORY
1 ..2 ..2 ..2 ..2 ..2 ..2 A/ACCE AC-TAPE C/WARR B/WARR C/REG BAG-PE RMT AA92-05387A ASSY-ACCESSORY;K15D,19,USA 0203-001279 TAPE-OPP MASKING;#232,T0.14,W15,L50000,Y AA68-01433A CARD WARRANTY;TV/TVCR,ALL,W/P100(G),B5, AA68-01561A CARD WARRANTY;BLOCK,STATEMENT ONLY,SEA/S AA68-01969A CARD;REGISTRATION PRODUCT,W/P120(G),SEA AA69-01195A BAG PE;CL29A6W8X,HDPET0.012,93/4X151 AA59-10101M REMOCON; DP,TM59,-,-,AA59-10095T
ASSY COVER/REAR
1 A/REAR AA90-01711A ASSY COVER/REAR;TXJ1996MHX/XAA 0203-001279 TAPE-OPP MASKING;#232,T0.14,W15,L50000,Y 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR AA64-00154B CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,..2 TAPE-DY ..2 CB+CF ..2 B/C
7-4
Samsung Electronics
Electrical Parts List
7-2 TXM1997X/XAA
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-CHASSIS
1 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ....4 ....4 ....4 ....4 ...3 ...