Text preview for : XVM-R70.pdf part of Sony XVM-R70 Sony Overhead Monitor Service Manual
Back to : XVM-R70.pdf | Home
XVM-R70
SERVICE MANUAL
Ver. 1.2 2005.07
US Model Canadian Model AEP Model UK Model E Model
· This set consists of the following units.
MONITOR CONNECTION BOX REMOTE COMMANDER XVM-R70 XA-115 RM-X122
SPECIFICATIONS
Monitor XVM-R70
System Display Drive system Picture size Liquid crystal color display Manual flipdown panel TFT-LCD active matrix system 7 inches wide screen (16:9) 154 × 87 mm, 176 mm (6 1/8 × 3 1/2 in., 7 in.) (w/h, d)
Card remote commander RM-X122
Power requirements CR2025 lithium battery Operable range Approx. 2.5 m (8.22 ft.) Dimensions 52 × 125 × 10 mm (2 1/8 × 5 × 13/32 in.) (w/h/d) Mass Approx. 40 g (1 oz) (including batteries)
Picture segment 336,960 (w 1440 × h 234) dots Power requirements 12 V DC car battery (negative ground) Current drain Approx. 800 mA Dimensions 230 × 57 × 270 mm (9 1/8 × 2 3/8 × 10 3/4 in.) (w/h/d) Operating temperature 5 °C 45 °C (41 °F 113 °F) Mass Approx. 1.5 kg (3 lb 5 oz)
Supplied accessories
Connection box XA-115 (1) Card remote commander RM-X122 (with supplied battery) (1) Monitor cable (5 m) (1) Power supply cord (1) DC-DC cord (3 m) (1) Stereo Mini Plug-to-Plug cable (5 m) (1) Mounting plate (1) Screws (4) Tapping Screws (4) Operating Instructions (1) Design and specifications are subject to change without notice.
Connection box XA-115
A/V Output Output Impedance: less than 220 less than 100 pF Output Level: 0 dBs ±0.3 dB (0.775 V rms) (Vol Max) Video: 75 1Vp-p A/V Input × 3 Input Impedance: more than 10 K less than 1000 pF Input Level: ±1.3 dBs +0/0.3 dB (0.775 V rms) Video: 75 1 Vp-p DC output 7.5 V (max 2 A) Dimensions 150 × 42 × 80 mm (6 × 1 11/16 × 3 1/4 in.) (w/h/d) Mass Approx. 260 g (9 oz)
OVERHEAD MONITOR
9-961-143-03
2005G04-1 © 2005.07
Sony Corporation
e Vehicle Group Published by Sony Engineering Corporation
1
XVM-R70
TABLE OF CONTENTS 1. SERVICING NOTES ....................................................... 3 2. GENERAL
Location of Controls ............................................................... 4 Connection diagram ............................................................... 6 5-10. IR Transmitter Check ....................................................... 15 5-11. V COM Voltage/Position Adjustment .............................. 16 5-12. Video Adjustment ............................................................. 16 5-12-1. Brightness Signal Contrast Level (Y GAIN) ......... 16 5-12-2. Black Limiter Level Adjustment ............................ 16 5-12-3. White Limiter Level Adjustment ........................... 16 5-12-4. R Sub Brightness Adjustment ................................ 16 5-12-5. B Sub Brightness Adjustment ................................ 16 5-12-6. R Sub Contrast Adjustment ................................... 17 5-12-7. B Sub Contrast Adjustment ................................... 17 5-12-8. 1 Adjustment ....................................................... 17 5-12-9. 2 Adjustment ....................................................... 17 5-12-10. VCO Free Run Adjustment .................................... 17 5-12-11. V POS Adjustment ................................................. 17 5-12-12. H POS Adjustment ................................................. 17
3. DISASSEMBLY
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. Skirt (Base) ........................................................................ 8 Base Board ......................................................................... 8 SW Board ........................................................................... 9 Covers (Hinge) ................................................................... 9 LCD Block Assy .............................................................. 10 Case (LCD Rear) .............................................................. 10 Chassis (LCD) .................................................................. 11 LCD Board ....................................................................... 12 LCD1 ................................................................................ 12
6. DIAGRAMS
6-1. IC Pin Description ............................................................ 19 6-2. Block Diagram Video Section ...................................... 21 6-3. Block Diagram Display Section ................................... 22 6-4. Printed Wiring Board LCD Section (1/2) .................... 24 6-5. Printed Wiring Board LCD Section (2/2) .................... 25 6-6. Printed Wiring Board Base Section (1/2) ..................... 26 6-7. Printed Wiring Board Base Section (2/2) ..................... 27 6-8. Schematic Diagram LCD Section (1/3) ....................... 28 6-9. Schematic Diagram LCD Section (2/3) ....................... 29 6-10. Schematic Diagram LCD Section (3/3) ....................... 30 6-11. IC Block Diagrams .......................................................... 31
4. TEST MODE .................................................................... 13 5. ELECTRICAL ADJUSTMENTS
5-1. Equipment Used ............................................................... 14 5-2. Connection of Equipment ................................................ 14 5-3. Setup for Adjustment ....................................................... 14 5-4. DC-DC Converter Adjustment ......................................... 15 5-4-1. Frequency Adjustment ............................................. 15 5-4-2. 5V Voltage Adjustment ............................................ 15 5-4-3. Other Voltage Checks ............................................... 15 5-5. PLL Adjustment ............................................................... 15 5-5-1. Frequency Adjustment ............................................. 15 5-5-2. Frequency Check ..................................................... 15 5-6. Inverter High Voltage Check ............................................ 15 5-6-1. Voltage Check .......................................................... 15 5-6-2. Frequency Check ..................................................... 15 5-7. OSD Dot Clock Check ..................................................... 15 5-8. NTSC Subcarrier Check .................................................. 15 5-9. PAL Subcarrier Check ...................................................... 15
7. EXPLODED VIEWS
7-1. 7-2. 7-3. 7-4. Base (1) Section ............................................................... 34 Base (2) Section ............................................................... 35 LCD Section ..................................................................... 36 Connection Box Section (XA-115) .................................. 37
8. ELECTRICAL PARTS LIST ....................................... 38
Notes on Chip Component Replacement
· Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
XVM-R70 SECTION 1 SERVICING NOTES
NOTE FOR REPLACEMENT OF THE EEP ROM (IC402)
The EEP ROM (IC402) contains all data by which the LCD screen is defined. When the EEP ROM is replaced, the normal LCD screen will not appear. It is then necessary to write the data into the EEP ROM.
Ver 1.1
Writing Method: 1. Place the POWER SELECT switch on the set into the B position. 2. Turn power on. While holding the RESET key down, depress the R key. Then release the RESET key and the R key in this order. 3. Press the VOL key on the remote controller for more than 2 seconds. 4. The EEP ROM data will be written and the normal test mode screen will appear. After this, perform V COM voltage/position adjustment as well as VIDEO adjustment.
NOTE FOR REPLACEMENT OF THE SYSTEM CONTROL (IC400)
When the IC400 is replaced, the video system should be set again according to the destinations.
Setting Method: 1. Enter the test mode. (See page 13). 2. Select NTSC/PAL SELECT from the test mode menu. 3. Set the video system to the appropriate mode for each destination by using the Video mode NTSN NTSC DVD PACK PAL PAL DVD PACK Destination US, Canadian *MV-7101DS E AEP, UK
R
and
r
keys on the remote controller.
* MV-7101DS represents the MV-7101DS package monitor.
3
XVM-R70 SECTION 2 GENERAL
This section is extracted from instruction manual.
Location of controls
Monitor
1 OPEN button Press to open the monitor. 2 Receptor for the card remote commander/Transmitter for the cordless headphones 3 UP/DOWN (M/m) buttons Press to select the desired item.
4 MENU button Press to adjust the various display settings. 5 REVERSE button* Press to switch images upside down. 6 INPUT button Press to select the input source. 7 POWER button
* The reverse position of the display monitor You can close with the LCD surface out after turning around 180 degrees, and images on the screen can be turned upside down by pressing (REVERSE) on the monitor. Before closing the display monitor, make sure that the monitor is turned and facing the enclosure (you will hear a click). Each time you press (REVERSE) on the monitor, the reverse screen mode switches between on and off.
180°
c
c
REVERSE
continue to next page t
7
4
XVM-R70
Card remote commander RM-X122
A TT
POWER
A TT
POWER
INPUT
MENU
INPUT
MENU
VOL
MODE
VOL
MODE
TOP MENU ALBUM+
LIST
TOP MENU ALBUM+
LIST
MENU ENTER
SETUP
MENU ENTER
SETUP
DISPLAY
DISPLAY
ALBUM
ALBUM
OFF AUDIO SUBTITLE
OFF AUDIO SUBTITLE
For the monitor operations: 1 ATT button Press to quickly attenuate the volume. 2 VOL (volume) +/ buttons Press to adjust the volume. 3 INPUT button Press to select the input source. 4 POWER button 5 MENU button Press to adjust the various display settings. 6 MODE button Press to change the screen mode. 7 V/v buttons Press to select the desired item.
For DVD operations: When a Sony mobile DVD player is connected to this unit, you can control the basic functions with the card remote commander. 8 V/v (ALBUM +/) buttons 9 TOP MENU button 0 MENU button qa O button qs ./> buttons qd m/M ( ) buttons qf B/b buttons qg LIST button qh SET UP button qj ENTER button qk DISPLAY button ql u button w; OFF button wa SUBTITLE button ws AUDIO button
· For function details, refer to the operating instructions supplied with the DVD player. · Sony DVD changer DVX-100 is not controllable with this card remote commander.
Tip Refer to "Replacing the lithium battery" for details on how to replace the batteries (page 18).
8
5
5
XVM-R70
Ver 1.1
Connection diagram
Refer to the connection diagram for the proper connections. You can make connections shown in A area. Please ask a qualified technician for the other connections.
Black GND (1 m) To a metal surface of the car chassis
Black
GND (1 m)
Monitor cable (5 m) Overhead Monitor XVM-R70 (7-inch wide color LCD Monitor) RCA pin cord (optional)
Yellow
Back-up (5 m)
Fuse (8 A) Filter box Red ACC (5 m)
To car battery (12 V)
Fuse (1 A) Blue/White striped POWER REM (5 m) Max. supply current 0.3 A 4 Pin Power connector
To ignition switch (ACC position)
To a power amplifier
Connection box XA-113 (optional)
Connection box XA-115 Headrest Monitor XVM-H65 (optional) Monitor cable (5 m) (optional) To Remote Signal (IR) Output
Precautions on PS oneTM · Be sure to fasten PS oneTM in a safe place securely. · For your safety, do not use PS oneTM while driving your car. · Make sure that the operating voltage of PS oneTM is 7.5 V. Other voltages may cause malfunction, or damage PS oneTM.
To Audio L/R/Video Input
To 7.5 V DC Output
Connection box XA-115
Headphone jacks (stereo mini) Audio L/R/ Video Input 2 7.5 V (max 2 A) DC Output (for PS oneTM) Remote Commander Signal receiver cord (5m) (Stereo Mini jack)
Front:
Audio L/R/ Video Input 1 Audio L/R/ Video Input 3
RCA pin cord (optional) AV Cable (integrated audio/video) (optional)
DC-DC cord (3 m)
22 Pin connector
DVD (MV) connector*1
Rear:
4 Pin Power connector
Remote Signal (IR) Output*2
Audio L/R/ Video Outputs
Sony mobile DVD player DVX-11A (optional)
PS oneTM (optional)
16
*1 DVD (MV) connector is only for MV-101. For details, refer to the Installation/Connections manual supplied with MV-101. (AEP, UK model) 1 * Not used in this unit (US, Canadian, E model) *2 Not applicable to the Sony DVD changer DVX-100
* "PS one" is a trademark of Sony Computer Entertainment Inc.
17
6
6
XVM-R70 SECTION 3 DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET 3-1. SKIRT (BASE) (Page 8) BASE BOARD (Page 8)
3-2.
3-3.
SW BOARD (Page 9)
3-4.
COVERS (HINGE) (Page 9) LCD BLOCK ASSY (Page 10) CASE (LCD REAR) (Page 10) CHASSIS (LCD) (Page 11) LCD BOARD (Page 12) LCD1 (Page 12)
3-5.
3-6.
3-7.
3-8.
3-9.
7
XVM-R70
Note : Follow the disassembly procedure in the numerical order given.
3-1. SKIRT (BASE)
qa insulating sheet (base) 0 base plate 9 screw (+BTP 2.6 x 8)
6 two screws (+BTP 2.6 x 8)
5 skirt (base) 1 two screws (+B 2 x 6) 7 two screws (+PS 3 x 10) 4 two screws (+B 2 x 6) 3 two screws (+B 2 x 6) 8 two screws (+BTP 2.6 x 8) 2 two screws (+B 2 x 6)
3-2. BASE BOARD
7 lug 6 screw (+P 2 x 5)
BASE board
9 two screws (+PTPWH 2.6 x 5)
1 CN954
5 CN955 4 CN952 3 CN951
0 BASE board 8 two screws (+PTPWH 2.6 x 5)
2 CN953
8
XVM-R70
3-3. SW BOARD
1 two screws (+B 2.6 x 6)
2 SW board
3-4. COVERS (HINGE)
two claws
4 5 cover (hinge front)
3 cover (hinge rear)
2
1 two screws (+BTP 2.6 x 8)
9
XVM-R70
3-5. LCD BLOCK ASSY
3 LCD block assy 2 two screws (+PS 3 x 10)
1 two screws (+PS 3 x 10)
3-6. CASE (LCD REAR)
1 four claws
2 four claws
3 window (IR)
7 claw 6 claw 0 claw 4 two screws (+P 2 x 8)
5 claw
8 claw qa
three claws
9 claw
two claws
qs case (LCD rear)
10
XVM-R70
3-7. CHASSIS (LCD)
5 two screws (+P 2 x 5)
6 screw (+P 2 x 5)
7 screw (+P 2 x 5)
8 two screws (+P 2 x 5)
4 two screws (+P 2 x 5)
9
qf chassis (LCD)
3 screw (+P 2 x 8)
1 two tscrews (+P 2 x 8)
2 screw (+P 2 x 8)
LCD board
qd CN404
0 CN401
qs CN902 qa CN403
11
XVM-R70
3-8. LCD BOARD
3 screw (+B 2 x 6) 4 lug 5 retainer (LCD) 0 two screws (+P 2 x 8) qa LCD board 9 two tscrews (+P 2 x 8)
2 CN850 6 screw (+B 2 x 6) 7 retainer (LCD) 8 tirminal (LCD)
1 CN800
3-9. LCD1
2 two retainers (LCD, B) 1 two screws (+B 2 x 6) 3 screw (+B 2 x 6) 4 retainer (LCD)
5 screw (+B 2 x 6) 6 retainer (LCD) 7 insulating sheet (LCD)
8 LCD1
12
XVM-R70 SECTION 4 TEST MODE
Setting Method: 1. Place the POWER SELECT switch on the set into the B position. 2. Turn power on. While holding the RESET key down, depress the R key. Then release the RESET key and the R key in this order. 3. TEST MODE MENU is indicated.
Ver 1.1
Terminating Method: Select the MENU No. 7, SOFT REST using the MENU key on the remote controller and determine the selection using the INPUT key.
The FOR FACTORY Mode: The FOR FACTORY mode can be used to perform 13 different adjustment items with the remote controller. 1. Select the MENU No. 2, FOR FACTORY using the MENU key on the remote controller and determine the selection using the INPUT key. 2. The FOR FACTORY mode is now entered. The following items are selected in turn by pressing the INPUT key repeatedly.
V Com
Y Gain
Black Limt
White Limt
R SUB BRT
B SUB BRT
R SUB CONT
B SUB CONT
Gamma1
Gamma2
VCO Free
PLL/V Pos
H Pos
3. For each item selected, adjust so that the adjustment value is within the specified value range using the R and r keys on the remote controller. 4. After adjustment, press the MENU key on the remote controller to determine the adjustment value. Press the MENU key once more to change to the next item. 5. After all necessary adjustments are completed, select EXIT using the MENU key on the remote controller and press the INPUT key to display the MENU screen. Then, select No.7, SOFT REST using the MENU key and determine the selection using the INPUT key to terminate the TEST mode.
13
XVM-R70 SECTION 5 ELECTRICAL ADJUSTMENTS
5-1. EQUIPMENT USED
The following measuring equipment are used for these electrical adjustments: · Oscilloscope · NTSC pattern generator · Stabilized power supply · Digital voltmeter · Frequency counter
5-2. CONNECTION OF EQUIPMENT
Unless otherwise specified, the equipment should be connected as shown below.
NTSC pattern generator
VIDEO OUT (75 )
monitor XVM-R70
main board TP507(+) TP500(-)
connection box XA-115
BATT
GND
ACC
stabilized power supply 14.4 V
5-3. SETUP FOR ADJUSTMENT
The 10-step gray scale signal from the NTSC pattern generator is used as an adjustment signal for V COM voltage/position adjustment as well as VIDEO adjustment.
10-step gray scale signal (with burst), 1Vp-p, 75
14
XVM-R70
5-4. DC-DC CONVERTER ADJUSTMENT
5-4-1. Frequency Adjustment Adjustment Method: 1) Connect frequency counter between TP801 (+) and TP803 (). 2) Adjust RV801 so that the reading on the counter stands at the specified value. Specified value: 242 ± 3 kHz Adjustment location: LCD board 5-4-2. 5V Voltage Adjustment Adjustment Method: 1) Connect digital voltmeter between TP806 (+) and TP803 (). 2) Adjust RV802 so that the reading on the counter stands at the specified value. Specified value: 5.15 ± 0.02 V Adjustment location: LCD board
5-6. INVERTER HIGH VOLTAGE CHECK
Condition: DIMMER switch OFF 5-6-1. Voltage Check Checking Method: 1) Connect oscilloscope between TP853 (+) and TP854 () using high voltage proof probes (100:1). 2) Verify that the reading on the oscilloscope is at 550 ± 150 V (rms). Checking location: LCD board 5-6-2. Frequency Check Checking Method: 1) Connect oscilloscope between TP853 (+) and TP854 () using high voltage proof probes. 2) Verify that the reading on the oscilloscope is at 68 ± 3 kHz. Checking location: LCD board
5-7. OSD DOT CLOCK CHECK
5-4-3. Other Voltage Checks Checking Method: 1) Connect digital voltmeter between TP807 (+) (Vdd) and TP803 (). 2) Verify that the reading on the voltmeter is at 3.50 ± 0.2 V. 3) Connect digital voltmeter between TP805 (+) (Vgh) and TP803 (). 4) Verify that the reading on the voltmeter is at 17.5 ± 1.5 V. 5) Connect digital voltmeter between TP804 (+) (Vss) and TP803 (). 6) Verify that the reading on the voltmeter is at 12.0 ± 1.5 V. Checking location: LCD board 1. Dot Clock Check Checking Method: 1) Connect frequency counter between TP405 (+) and TP404 (). 2) Verify that the reading on the counter is at 6.5 ± 0.2 MHz. Checking location: LCD board
5-8. NTSC SUBCARRIER CHECK.
1. Subcarrier Check Checking Method: 1) Press the INPUT key on the remote controller and enter the NTSC mode using the R and r keys. 2) Connect frequency counter between TP508 (+) and TP500 (). 3) Verify that the reading on the counter is at 3.579545 MHz ± 100 Hz. Checking location: LCD board
5-5. PLL ADJUSTMENT
5-5-1. Frequency Adjustment Adjustment Method: 1) Connect digital voltmeter between TP616 (+) and TP600 (). 2) Adjust RV600 so that the reading on the counter stands at the specified value. Specified value: 2.5 ± 0.15 V Adjustment location: LCD board 5-5-2. Frequency Check Checking Method: 1) Connect frequency counter between TP612 (+) and TP600 (). 2) Verify that the reading on the counter is at 14.4 ± 0.2 MHz. Checking location: LCD board
5-9. PAL SUBCARRIER CHECK
1. Subcarrier Check Checking Method: 1) Press the INPUT key on the remote controller and enter the PAL mode using the R and r keys. 2) Connect frequency counter between TP508 (+) and TP500 (). 3) Verify that the reading on the counter is at 4.433619 MHz ± 100 Hz. Checking location: LCD board
5-10. IR TRANSMITTER CHECK
1. VCO Frequency Check Checking Method: 1) Input 400 Hz, 20dB V to TP354 for L channel and TP350 for R channel. 2) Connect frequency counter to TP353 for L channel and TP352 for R channel. 3) Verify that the reading on the counter stands at the specified value. Specified value: 2.3 MHz ± 45 kHz for L channel 2.8 MHz ± 45 kHz for R channel Checking location: LCD board
15
XVM-R70
5-11. V COM VOLTAGE/POSITION ADJUSTMENT
Condition: TEST MODE (See 13 page) 1. Voltage Setup Adjustment Adjustment method: 1) Select V Com from the FOR FACTORY MODE. 2) Connect oscilloscope between TP809 (+) and TP600 (). 3) Adjust so that the p-p value A of the waveform stands at the specified value using the R and r keys on the remote controller. 4) Adjust so that the level B on the negative side stands at the specified value using RV801. 5) Verify that the level C on the positive side stands at the specified value. Specified value A: 5.6 ± 0.1 Vp-p Specified value B: 1.1 ± 0.1 V Specified value C: 4.5 ± 0.1 V
C 0V A B
5-12-3. White Limiter Level Adjustment Adjustment Method: 1) Select White Limit from the FOR FACTORY MODE. 2) Connect oscilloscope between TP811 (+) and TP500 (). 3) Adjust so that the signal level C stands at the specified value using the R and r keys on the remote controller. Specified value: 3.85 ± 0.05 V
C
0V
Adjustment location: LCD board 5-12-4. R Sub Brightness Adjustment Adjustment Method: 1) Select R SUS BRT from the FOR FACTORY MODE. 2) Connect oscilloscope between TP812 (+) and TP500 (). 3) Adjust so that the signal level D stands at the specified value using the R and r keys on the remote controller. Specified value: 1.1 ± 0.1 V
Adjusting location: LCD board
5-12. VIDEO ADJUSTMENT
Conditions: TEST MODE (See 13 page) 10-step gray scale signal input NTSC mode 5-12-1. Brightness Signal Contrast Level (Y GAIN) Adjustment Method: 1) Select Y Gain from the FOR FACTORY MODE. 2) Connect oscilloscope between TP811 (+) and TP500 (). 3) Adjust so that the signal level A stands at the specified value using the R and r keys on the remote controller. Specified value: 3.4 ± 0.1 V
D
0V
Adjustment location: LCD board 5-12-5. B Sub Brightness Adjustment Adjustment Method: 1) Select B SUS BRT from the FOR FACTORY MODE. 2) Connect oscilloscope between TP810 (+) and TP500 (). 3) Adjust so that the signal level E stands at the specified value using the R and r keys on the remote controller.
A
0V
Specified value: 1.1 ± 0.1 V
Adjustment location: LCD board 5-12-2. Black Limiter Level Adjustment Adjustment Method: 1) Select Black Limit from the FOR FACTORY MODE. 2) Connect oscilloscope between TP811 (+) and TP500 (). 3) Adjust so that the signal level B stands at the specified value using the R and r keys on the remote controller. Specified value: 0.65 ± 0.01 V
E
0V
Adjustment location: LCD board
B
0V
Adjustment location: LCD board
16
XVM-R70
5-12-6. R Sub Contrast Adjustment Adjustment Method: 1) Select R SUB CONT from the FOR FACTORY MODE. 2) Connect oscilloscope between TP812 (+) and TP500 (). 3) Adjust so that the signal level F stands at the specified value using the R and r keys on the remote controller. Specified value: 3.4 ± 0.1 V
5-12-9. 2 Adjustment Adjustment Method: 1) Select Gamma2 from the FOR FACTORY MODE. 2) Connect oscilloscope between TP811 (+) and TP500 (). 3) Adjust so that the signal level I stands at the specified value using the R and r keys on the remote controller. Specified value: 3.1 ± 0.1 V
F I 0V 0V
Adjustment location: LCD board 5-12-7. B Sub Contrast Adjustment Adjustment Method: 1) Select B SUB CONT from the FOR FACTORY MODE. 2) Connect oscilloscope between TP810 (+) and TP500 (). 3) Adjust so that the signal level G stands at the specified value using the R and r keys on the remote controller. Specified value: 3.4 ± 0.1 V
Adjustment location: LCD board 5-12-10. VCO Free Run Adjustment Adjustment Method: 1) Select VCO Free from the FOR FACTOR MODE. 2) Connect frequency counter between TP407 (+) and TP404 (). 3) Adjust so that the reading on the counter stands at the specified value using the R and r keys on the remote controller. Specified value: 15,734 ± 50 Hz Adjustment location: LCD board 5-12-11. V POS Adjustment Adjustment Method: 1) Input mono scope signal from the NTS pattern generator. 2) Select PLL/V POS from the FOR FACTORY MODE. 3) Observe the mono scope screen on the monitor and adjust so that the screen is vertically symmetrical using the R and r keys on the remote controller. 5-12-12. H POS Adjustment Adjustment Method: 1) Input mono scope signal from the NTS pattern generator. 2) Select H POS from the FOR FACTORY MODE. 3) Observe the mono scope screen on the monitor and adjust so that the screen is horizontally symmetrical using the R and r keys on the remote controller.
G
0V
Adjustment location: LCD board 5-12-8. 1 Adjustment Adjustment Method: 1) Select Gamma1 from the FOR FACTORY MODE. 2) Connect oscilloscope between TP811 (+) and TP500 (). 3) Adjust so that the signal level H stands at the specified value using the R and r keys on the remote controller. Specified value: 1.9 ± 0.1 V
H 0V
Adjustment location: LCD board
17
XVM-R70
Adjustment Location:
LCD BOARD (SIDE A)
RV351 CN850 TP353 TP803 TP853 TP854 TP804 TP805 TP806 TP807 TP354 T850 RV802 T800 CN902 CN403 TP507 TP810 TP404 TP407 IC400 RV800 TP405 TP500 TP811 CN401 TP600 RV600 TP812 TP801 CN404 TP809 6-pin TP350 IC350 RV801 CN800 IC601 4 8 1 RV601 TP352 RV350
TP612
TP508
18
XVM-R70 SECTION 6 DIAGRAMS
6-1. IC PIN DESCRIPTION
· IC400 µPD780022AY-N14-9ET (SYSTEM CONTROL) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 Pin Name P50 PW-ON P52 P53 P54 S-SCL S-DATA O/H SELECT VSS VDD1 N/P SEL P31 SDA SCL P34 SCK SDATA P20 OSD DATA OSD CLK PS-ON OSD CS N/P VDD2 AVSS P17 KEY IN P15 P14 P13 P12 PW DET P10 AVREF AVDD RESET XT2 XT1 IC X2 X1 VSS1 VSYNC KEY HALT REM HALT ACC ON REM IN ACC Y/N IR CONT P-ON SW P74 I/O I O -- -- -- O I/O I -- -- I -- I/O O -- O I/O I O O O O O -- -- -- I -- -- -- -- I -- -- -- I -- -- I O I -- I I I I I I O I -- Test mode setting input Power ON control signal output Not used (Open) Not used (Open) Not used (Open) Sound I2C clock signal output Sound I2C serial data input/output Over-head/Head-rest select signal input Ground Power supply pin (+3 V) Not used (Open) Not used (Open) EEPROM data input/output EEPROM clock output Not used (Open) Video I2C clock signal output Video I2C serial data input/output Sync. detection signal input OSD data output OSD clock output Not used (Open) OSD chip select output NTSC/PAL select signal output Power supply pin (+3 V) Ground Not used (Open) A/D key signal input Not used (Open) Not used (Open) Not used (Open) Not used (Open) Power voltage detection signal input Not used (Open) Power supply pin (+3 V) Power supply pin (+3 V) System reset input Power supply pin (+3 V) Ground Ground Crystal oscillator Crystal oscillator Ground Vertical sync signal input Key halt detection signal input Remocon halt detection signal input ACC ON detection signal input Remocon signal input ACC type YES/NO select signal input IR control signal output Power ON SW detection signal input Not used (Open) Pin Description
19
XVM-R70
Pin No.
Pin Name
I/O
Pin Description
52 53 54 55 56 57 58 59 60 61 62 63 64
P75 A MUTE UD LR TFT ON SIDE3 SIDE2 SIDE1 DIMMER P44 SW2 SW1 P47
-- O O O O O O O O -- O O --
Not used (Open) Audio muting signal output LCD up/down reverse control signal output LCD left/right reverse control signal output LCD ON/OFF control signal output Display size 3 control signal output Display size 2 control signal output Display size 1 control signal output LCD backlight dimmer control signal output Not used (Open) A/V input 2 select signal output A/V input 1 select signal output Not used (Open)
20
XVM-R70
6-2. BLOCK DIAGRAM -- VIDEO SECTION --
VD PULSE SHAPE Q500 34 35 VD IN VCO I/N
IC500 RGB DECODER HD OUT
CSYNC
32
HD
SYNC SEP Q501,502 CN950 CVBS
46
CSYNCIN
2 (Page 22)
HH KILL V COUNT VD OUT 31 VD
SYNC SEP
R 57 C IN BPF/ ACC R-Y/B-Y DEMOD G-Y GEN MATRIX OSD SW BRIGHT/ CONTRAST INVERT RGB OUT
26 G 21 B 19
R G B
1 (Page 22)
BATT+ 52 BATT POWER CONTROL Q951,956 POWER CONTROL Q957,958 BATT+ BATT+ 1 5V REG IC953 3 3 3.3V REG IC952 2 D410 3.3V
Y IN
SDATA SCLK
SW
R IN2 G IN2 B IN2 YS
SYNC OUT
DELAY/ SHARP HSYNCLOCK
VXO
POL 36 VCOM 28
POL VCOM PAL
3 (Page 22)
53
54
39
48 47
14 15 16 17
12V
S950 (POWER SELECT)
X500 3.579545MHz
63 64
X501 4.433619MHz TRAP CONTROL Q503
POWER CONTROL Q406,407
ACC5V
TRAP 16 17 18 15
AMP REM
D903 D902
IC400 (1/2) SYSTEM CONTOL ACC CHECK Q403
VR VG VB VBLK
POWER CONTROL Q952,954
BATT+
H PULSE SHAPE Q504,505
H SYNC CG ROM H CONT OSC V CONT V SYNC
20
ACC DET POWER ON Q401 Q402
46 ACC ON 2 PW ON 48 ACC Y/N
P20 18 SDATA 17 SCK 16 DATA 19 CLK 20 CS 22 3 DATA 1 SCLK 2 CSN
VIDEO RAM
DATA SELECT
OUTPUT CONTROL
Q400 SIRCS V-SDATA V-SCL A MUTE SW1 SW2
REMOTE CONTROL 1 RECEIVER IC404
47 REM IN 45 REM HALT
OSD
19
IC401 CHARACTER GENERATER VSYNC 43 7 6 53 63 62 S-DATA S-SCL A MUTE SW1 SW2 L IN 16 IR CONT 49 IC350 AUDIO IR TRANSMITTER VREF 6 L OUT Q350 9 IR DRIVE Q352,353 Q351 8 12V RV350 L-CH VCO
L-CH IR R-CH IR
AGC
PRE EMPHASIS LEVEL DETECT
VCO
BUF
R IN 1 AGC
PRE EMPHASIS
R OUT VC0 BUF
Signal path : AUDIO : VIDEO
VREF
11 RV351 R-CH VCO
21
21
XVM-R70
6-3. BLOCK DIAGRAM -- DISPLAY SECTION --
IC501 RGB BLANKING
VR AN 14 BN 15 VG VB CN 4 6
VR VG 5 2 IC601 VCO VCC Q506 OSC BIAS Q600,D601 RV601 VCO VB
R
13 1 3
AI BI S0 S1 S2 CI
(Page 21)
1
G B
AO 12 BO 2 CO 5
RV600 PLL FREERUN 50
IC600 DISPLAY CONTROL PDOS
11 10 9
44 OSCI OSC
PLL DET H COUNT
H OUT
(Page 21)
2
HD VD
22
HD OUT
MASK
59 53 54 56
CPH1 STH1 STH2 HDIR
LCD1 LIQUID CRYSTAL DISPLAY PANEL
14 8 Q601 PAL 19 13
POLC NBLK PAL POLS V COUNT
(Page 21)
3
V OUT
POL VCOM BATT 23 N/P 32 PW DET
LR 55 SIED 1 59 SIDE 2 58 SIDE 3 57 UD 54
21 18 5 6 7
VD OUT MIRROR MODE1 NODE2 MODE3
V SEL
FIELD DET INT/EXT SEL
28 25 32 31 30 29 27 17
CPV STV1 STV2 OEV1 OEV2 OEV3 CX UPSD
12V
3
8V REG IC351
1
8V
EEPROM IC402
5 6
13 SDA 14 SCL 6
COM OSC IC801
1
VCOM DRIVE Q802-804
VCOM RV801 VCOM BIAS
T800 12V IC800 SWITCHING REGULATOR PWM COMP PWM OUT ERROR AMP 2 RV800 DC-DC FREQUENCY ON/OFF DRIVE Q800,801
D801 VGH D802 VEE VDD D803 RV802 SW REG ADJUST
KEY IN 27 KEY HALT 44 KEY IN DETECT Q404,405
KEY-IN S401-406
T850 12V P50 50 IC400 (2/2) SYSTEM CONTROL S501 (DOOR) POWER CONTROL Q855,856,859 11 PULSE STEERING F/F 16 ERROR AMP IC850 BACK LIGHT CONTROL SWITCH Q857,858
BACK LIGHT
OSC
7
VGL D800
D853
3 RESET 36 40 X2 41 X1 1 RESET IC403 3 3.3V
X400 4.19MHz
S951 (RESET) 12V
POWER CONTROL Q853,854
12
PWM COMP
ERROR AMP
1
CURRENT DETECT Q850
Signal path : VIDEO
TFT ON 56 DIMMER 60
22
22
XVM-R70
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. · % : indicates tolerance. f · : internal component. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · · · · Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
· Waveforms (LCD Board)
1
1V/DIV 50µsec/DIV
9
3.5Vp-p
5V/DIV 5µsec/DIV
qj
13.2Vp-p
0.2V/DIV 50nsec/DIV
5.4Vp-p 14.48MHz
127µsec
8.4µsec
TP505
TP850
TP612
2
0.2V/DIV 20µsec/DIV 1Vp-p H
0
10V/DIV 5µsec/DIV
qk
30.7Vp-p
5V/DIV 2µsec/DIV 11.8Vp-p 4.2µsec
14.7µsec
TP506
TP851
TP801
3
0.2V/DIV 20µsec/DIV 1Vp-p H
qa
1V/DIV 5msec/DIV 3.5Vp-p 16.4µsec
ql
10V/DIV 2µsec/DIV 35Vp-p 4.2µsec
·
·
·
· ·
·
A : B+ Line. B : B Line. H : adjustment for repair. CN401 of XVM-R70 is connected to Connection Box with a monitor cable. Power voltage is dc 14.4 V from ACC cord of the Connection Box and fed with regulated dc power supply. CN401 of XVM-R70 is connected to Connection Box with a monitor cable. Voltage and waveforms are measured at input the color bar signal from the Connection Box. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : AUDIO g : VIDEO Abbreviation CND : Canadian model.
TP507
TP601
TP802
4
0.2V/DIV 200nsec/DIV 0.8Vp-p 3.5714MHz
qs
1V/DIV 50µsec/DIV 3.5Vp-p 128µsec
w;
0.5V/DIV 20µsec/DIV 2.2Vp-p 63µsec
TP508
TP602
TP808
5
0.5V/DIV 200nsec/DIV 1.1Vp-p 2.8MHz
qd
1V/DIV 20µsec/DIV 3.5Vp-p 62.6µsec
wa
2V/DIV 50µsec/DIV 4.4Vp-p 127µsec
TP352
TP603
TP809
6
0.5V/DIV 200nsec/DIV 1.1Vp-p 2.3MHz
qf
1V/DIV 50µsec/DIV
ws
3.5Vp-p
1V/DIV 20µsec/DIV 3.3Vp-p 2H
190.9µsec
TP353
for printed wiring boards: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. · : Pattern from the side which enables seeing. Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
TP606
TP810
7
1V/DIV 10msec/DIV 3.5Vp-p 16.5µsec
qg
1V/DIV 10µsec/DIV 2.8Vp-p 63.4µsec
wd
1V/DIV 20µsec/DIV 3.2Vp-p 2H
TP406
TP609
TP811
8
1V/DIV 20µsec/DIV 3.6Vp-p 64µsec
qh
1V/DIV 50nsec/DIV 3.6Vp-p 7.2MHz
wf
1V/DIV 20µsec/DIV 3.3Vp-p 2H
· Abbreviation CND : Canadian model.
TP407
TP611
TP812
23
23
XVM-R70
6-4. PRINTED WIRING BOARD -- LCD SECTION (1/2) -- · Refer to page 23 for Common Note on Printed Wiring Boards.
13
12
11
10
9
8
7
6
5
4
3
2
1 A
· Semiconductor Location
Ref. No. D356 D501 D602 D603 D604 D804 D805 D852 D853 D854 D855 IC401 IC402 IC403 IC500 IC501 IC600 IC800 IC801 IC850 Q400 Q401 Q402 Q500 Q501 Q502 Q503 Q601 Q802 Q803 Q804 Q850 Q853 Q854 Q855 Q856 Q857 Q858 Q859 Location C-8 G-10 D-12 D-12 D-12 C-4 C-4 G-1 C-3 G-3 G-3 H-7 H-9 H-8 H-11 F-12 E-11 G-4 D-9 G-2 B-7 B-6 B-7 G-12 I-11 I-11 I-12 F-10 D-9 D-9 D-10 G-2 H-3 H-3 G-2 G-1 F-1 F-2 G-2
R415
R482
Q402
R417 R480
R414
R416
B
Q401
LCD BOARD (SIDE B)
Q400
D804
D805
D356
C831
R873
C835
C833
L807
L809
C837
L808
L810
C857
D604
D602
L803
L806
L805
C622
R643
R820 Q802 R823 Q804 Q803 R822
R821 R816
R826
C813 R819
D603 C617 C618
L603
L802
R648
C816
L804
C627
R872
R874
D853
C
D
8 IC801 1 R817
5
JC801 C818 C827 C824 C821
4
C604
R629 C607
C602
R659 R627 R626 33 32 R625 R624 R623 R622
R818
49
48
E
R630
R633
R631 C608 R632 IC600
C609
C601 R621 R618 R619
R867
FL601
R634
C611
R600 C612
1
R604 R606
R602
C600 R614
R613 R615 R608 R809 R610
R617 R658
R616
R635 Q601
R657
R655 R654
Q858
R866
R868
64
17 16
Q857
C855
F
Q859
D852 Q856
R656
D854
9
IC501
8
R885
R886
Q850 Q855
R864 R865
16
1
C518 C515 C514 R810 R502 R501
R887 R875
R876 R877
R879
R878 C858
C806 9
IC800
C802
R403
L500
R811 C808 R469 R464 R440 C426 R441 C403 1
R470
R402 D501
R803
R804 8
C809
R813 R445 C413 1
IC401
D855
R862 16
G
C520
C517
R505
C519
X400
IC402
5
R455
4 R412
R442 R443 R444
20
R449 R448 R447
R815 R814
C800
R507
C523 C524 C527
R530
C522
32 33
17
16
C509 C508 C507 C505 C504 8
C411
3 IC403
2
R410
R802
16
1
1
8 Q854
R861
IC850
R506
Q500
R500
R504
C516
R451 R450
R812 C810
C407 C406
R801
C801
1
89
R411 C425
R508 C525 R509 C526
R531 R532 C528
10
11
R446
IC500
R439 R438
H
48 49 C531
R517
1 64
R858
C502 R520
C539 C541
R859
C503
Q853 C540
R534 R533
R510
L503 C535 C536 C529 C532 C537
Q502
R515
R860
R519 R518 Q503
C534
R512
Q501
R514
I
R521 C530
C547
R535
J
1-688-87011
24
24
XVM-R70
6-5. PRINTED WIRING BOARD -- LCD SECTION (2/2) -- · Refer to page 23 for Common Note on Printed Wiring Boards.
1 A
2
3
4
(Page 27)
BASE BOARD CN953
5
6
7
8
9
10
11
12
13
(Page 27)
C422
BASE BOARD CN952
B
D350
D351
D352
3
IC404
C
NL850
(Page 27)
D353 D354 Q351 D355 Q350 D353-355 (LCD BACK LIGHT) BASE BOARD CN951
LCD1 LIQUID CRYSTAL DISPLAY PANEL
· Semiconductor Location
Ref. No. D350 D351 D352 D353 D354 D355 D400 D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D412 D500 D600 D601 D800 D801 D802 D803 IC350 IC351 IC400 IC404 IC601 Q350 Q351 Q352 Q353 Q403 Q404 Q405 Q406 Q407 Q504 Q505 Q506 Q600 Q800 Q801 Location A-5 A-5 A-6 A-8 A-8 A-9 J-8 F-7 F-7 F-7 F-8 F-8 F-8 F-9 F-9 H-10 H-6 B-6 G-6 H-12 F-12 E-12 E-5 E-3 E-4 E-5 C-8 C-6 H-9 A-7 D-12 B-8 B-8 B-5 B-6 I-9 I-8 I-8 F-9 F-9 H-12 I-12 G-11 F-12 G-4 F-4
D350-352 (LCD BACK LIGHT)
C408
1
Q352
R364 R363
Q353 R365 R366
C351 C361
TP353 9
IC350
R361 R362
B
LCD BOARD (SIDE A)
CN850 2 TP856
D411 RV351
D
RV350 R351 C360 8 TP352
C358
TP803
C359
C836
C834
C830
C832 1
16 2
C363
1
TP853
TP854 C823 T850
C353
IC351 3 C826 C829 C820
C362
C356
C
C350
R352
1
C357 TP817 TP816 TP815
C364
C354
C352
TP804
TP806
TP807 C828 C819
R354 TP354 TP351 TP350
R350 C811
C812
C355
TP813
R824
D
TP805
C822
C825
RV801
C619 CN800 30 TP601 TP610 1 R645 R647 R644 R642 C621
R641
R456
R825
C620 R646 TP607 5 8 TP609 TP611 TP606 IC601 4 1 TP604 TP603 TP616
R831
TP808 D803 RV802 R832 D800
R452
C814
C815
D801
D802
TP809 TP606 TP602 TP618
C605
E
T800
L600
TP612
R637 C614
L602
R636
TP608
RV601
D601 C613 RV600 R635 D600
R827
C805
C606
C603
R662 C615 Q600
R638 R639 C616 R529
CN902 TP802 Q801 7 1 1
CN403 6 TP409 TP408 TP903 TP507
D401 D402 D403 D406
CN401 1 12 Q406
R479
C817
TP600
R640
C628
TP614 Q407 R478 R475 R476 R477 TP613 TP614 R661 R660
TP851
TP852
R454
F
L800
TP416 TP418
D404 D405
TP420
CN404
D407
C807
C804
C838
C867
L852
R806 R805 R809 R808
R833 TP801 C866
L801
TP406 TP422 TP404 D412 TP407 R404 R405
C414 C412
R526 TP411 TP414
R401 R465 R466 R484 R400 C400
R528
TP900
TP902
2 1
TP419 TP412
D408
TP615
R527 Q506 TP505
C626
TP810
TP812
TP850
C803
TP855
TP410
R457
TP811 C546 TP413
R430 R429 R424 L501 L502
G
L851 R880 C860 C862 R883 C861 R884 C859 R881 R882
TP800
TP403 17 16 1 64
R807 RV800
Q800 TP400 R800
C513 TP500
C521
R428 R407
C401
R427 IC400 R426 R425 R423 32 49 48 BP1 C404
C405
R408 TP417 TP405 TP415 C402 L400
F800
C865
H
R409
C851 C850
C415
33
R422 TP402 TP501 TP503 TP403 TP502
D409
C511 X500
C543
R852
C416
L402
R851
C417
R522
Q504 R523 C545
R524
R483 C424
R418
C506
D410
C409
R420
C510
C542
R419 Q403
TP904 F850 L850
C423
R473 R437
R421
Q505 TP508
C548 C501
C500
R471 TP401 Q404 C418 R474
R472
C410
I
TP506
Q405 D400 R432 R433 R434 S403 MENU R435 S401 UP V S404 DOWN v S405 POWER S406 INPUT R436 S402 REVERSE
J
A
BASE BOARD CN955
1-688-870
11
(Page 27)
25
25
R525
D500
R850
TP504
C512
C544
X501
XVM-R70
6-6. PRINTED WIRING BOARD -- BASE SECTION (1/2) -- · Refer to page 23 for Common Note on Printed Wiring Boards.
14
13
12
11
10
9
8
7
6
5
4
3
2
1 A
B
BASE BOARD
(SIDE A)
C
S951 (RESET)
D
TP975 TP956 TP951 TP972 TP961 TP973 11 22 20 5 15 1 12 TP980 TP966 TP977 CN950 TP958 TP960 TP963 TP962 TP964 TP968 TP970 TP976 TP969 TP967 TP965 TP971 TP957 TP959 TP956
TP978 TP979
E
F
TP953 TP952
C951
C952
C961
G
TP950
H
1-688-87111
I
26
26
XVM-R70
6-7. PRINTED WIRING BOARD -- BASE SECTION (2/2) -- · Refer to page 23 for Common Note on Printed Wiring Boards.
1 A
2
3
4
5
6
7
SW BOARD
8
(SIDE B)
9
10
SW BOARD
11
(SIDE A)
12
13
14
· Semiconductor Location
Ref. No. D901 D902 D903 IC952 IC953 Location D-12 E-3 E-3 G-4 H-5 Ref. No. Q951 Q952 Q954 Q956 Q957 Q958 Location H-8 H-8 G-7 G-7 H-7 H-8
S951 (DOOR)
B
TP977 TP978
C
BASE BOARD
(SIDE B)
(Page 25)
LCD BOARD CN404 BLK
1-688-872-
11
1-688-872-
11
(Page 25)
LCD BOARD CN902
(Page 25)
LCD BOARD CN401
(Page 25)
LCD BOARD CN403
RED
BLK
2 W950
A
C
D
B
1
D901
D
CN952 1 7 1 CN951 12 1 CN953 6 R971 -1 R954 R951 R950 D903 -2 D902 R952 R973 R955 C950 CN954 1 2
R976
R977
E
S950 (POWER SELECT) B
CN955
F
A GRY 2 1
R969
R974
L951
G
C953
IC952 1 2 3 3
Q954 IC953 1
R962 VDR950
C956
C957
C955
R968
R975
F950
C959
C960
R959
R965
L950
R970
R957
2
Q958 R967 R966
Q956
R958
R956
Q951
TH950 Q957 Q952
C958
H
R960
1-688-871-
11
I
27
27
R972
XVM-R70
6-8. SCHEMATIC DIAGRAM -- LCD SECTION (1/3) -- · Refer to page 23 for Waveforms and Common Note on Schematic Diagram and page 31 for IC Block Diagrams.
CN950 R977 R976 R972 CN953 TP966 TP969 TP970 TP973 TP972 TP965 CN952 TP961 TP962 TP963 TP964 TP960 TP955 TP956 R971 CN951 TP953 TP968 TP967 TP971 D901
CN954 S951 TP977 TP978
TP975 TP976
R950 TP957
TP951
L950
Q956
TP950 TH950 F950
Q952
Q957 TP954 R960 VDR950 R966 R967 Q958 R965 R968 R969 R974 R975 L951 C957 C955 IC953 IC952
R973 TP958 TP959 CN955 S951 TP980 TP979 C958 D902 D903 S950 TP978 TP977
R951 R954
R956 R970 R962 R958 C961 C952 Q954
Q951
R959
R952 R955 C950
C951
C959
R957 TP952
C960
C956
C953
R533
R534
R522
Q504 Q505
R525
D500 R523
R524 C545 R506 C519
C526
R531
R530
R507
R532
R509
C528
C525
C522
CN404 TP422 R515 CN403 TP507 C530 C547 R521 TP408 CN902 TP900
D401 D402 D403
Q500 R505
TP505
R504
C527
R510
Q501
C524
C529
IC B/D
Q502 TP506 R512 C531 R514
R519 R535 Q503 C534 R518 TP903 C533 L503 R517 C535 C536 C537 C538 C515 R452 C539 C540 R520 C541 C542 X500 C543 X501 TP508 C514 R500 C513 C544 L501 R501 IC500 C518 R502 C517 C516 C520 C532 C521
TP901
R508
C523
L502
CN401 TP409 TP410 TP411 TP412 TP413 TP414 TP415 TP416 TP418 TP419
(Page 30)
TP501 TP502 TP503
D501 C500
C503 C506 C510 C504 C505 C507 C508 C502 C509 C511 C512
L500 C548 TP500
D406 D404 D405
C501
TP504
R454
(Page 29)
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
28
28
XVM-R70
6-9. SCHEMATIC DIAGRAM -- LCD SECTION (2/3) -- · Refer to page 23 for Waveforms and Common Note on Schematic Diagram and page 31 for IC Block Diagrams.
(Page 28)
D410
L400 D412 C423 C402 C426 C401 R445 R440
IC B/D
IC401 TP407 R451 R450 R449 R448 R447 R446 TP406
R442
R473 Q405 D400 Q404 C418 R474 C410
R437
R409
R408 R407
R405 R404
R457
R471 R472
TP400 C403
C412 R443 C413 C414 R444 TP405 C416 C415 TP403 TP402
S401
S402
S403
S404
S405
S406
R470 TP404 C417 L402 R402 R403 R438 R439
C425
IC403
R432
R433
R434
R435
R436
R411
Q406 R479 R478 Q407 R476 D408 IC404
R480
R414 R418 R482 R417 R419 TP401
C405 C404 C400 BP1 C406 C407 X400 Q403 R421 D409 Q401 R483 R420 C424 R484 C409 R455 R464 R410 R412 R401
R441
(Page 30)
IC400 C411
Q400 R415
Q402
R477
R475 D407
C408 C422 D411
IC402
R416
C363C361 R352 R456 R354 C362 C360 R351
RV351 TP354 C364 D352 D351 D350
D356
IC351
IC B/D
IC350
Q352 R363 R364 Q353 Q351 TP352 R350 C356 C359 C355 C357 C358 L852 F850 TP904 R861 Q854 C865 C850 C851 R858 R850 R851 R852 R878 R879 R875 R876 R877 C858 IC850 TP855 R880 R882 R881 R883 C861 R884 C862 R886 R887 Q850 C859 R885 D855 D854 Q859 R859 C866 R865 Q857 Q858 TP854 C857 R860 Q853 C867 TP851 TP852 R862 Q855 D852 L850 Q856 TP850 L851 TP853 CN850 NL850 TP856 C855 T850 TP351 RV350 Q350 R361 R362 R365 C352 C353 R366
D355 D354 C354 TP350
D353
R469 R422
R423 R424 R425
R426 R427
R428
R429
R430
C350
C351
R400 R466 R866
R465 R867 R868
TP353
R864
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
C860
29
29
R872 R873 R874
D853
XVM-R70
6-10. SCHEMATIC DIAGRAM -- LCD SECTION (3/3) -- · Refer to page 23 for Waveforms and Common Note on Schematic Diagram and page 32 for IC Block Diagrams.
TP614 L600 C606 C605 C604 C603 C602
TP608
R659
R638
R639
C626
IC B/D
C620
IC601
C621
RV601
Q600 R640 R662 R627 R626 TP607 TP606 TP605 TP604 TP603 TP602 C628 TP601 R635 RV600 D601 L602 R636 C617 TP612 R637 C615 C616 C614
C607
R629 TP609 TP610 R630 R631 R632 C609 TP611 C608 R633 FL601 C611 IC600
R625 R624 R623 R622 R621 R619 R618 R655 R654 R617
R647
R645 R644 D603
D600
R641 C618 R642 C619 R643 D604
R646
IC B/D
R648 C622 D602 C627
C613
L603
C601
(Page 28)
R634
R616 R615
IC B/D
C612 R528 R658 Q601 Q506 R529 R526 R657 R527 IC501
TP615
R661
R602
R606
R608
R610
R600
R604
R609
R660
R613
R614
R656 C600 TP600
C546
CN800 TP808 C817 R827 R826 TP813
R816 TP814 R819 R820 Q802 Q804 C816 F800 R813 C808 R811 R810 TP817 C807 C806 L801 C811 C812 C815 R817 C813 R818 Q803 R821 R822 R825 RV801 TP809 LCD1 TP815 TP816 R823 R824
IC801
R815
R812
C810
R814
C809
C814
JC801 D800 C818 L800 T800 L803 C819
L802 TP804 C820 TP805
L808 TP818 L810 L809 TP806 D804 D805 TP810 TP811 L807 TP807 TP812
(Page 29)
IC800 R808 R805 Q801 R809 C804 C805
D801
L804 C821 D802 C822 C823
L805 R831 C824 RV802 C825 C826
TP801 R801 RV800 TP800
Q800 R806
TP802
C801
C838 D803
L806
C835
C831
C833
C832
C836
C834
C830
R803 C802
R800
C800
R802
R804
C803 R807
R833
R832
C827
C828
C829
TP803
30
30
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
C837
XVM-R70
6-11. IC BLOCK DIAGRAMS
IC500 AN2546FH-AV
NAVI SYNC IN HSYNC LOCK CSYNC OUT +BCLKFLT CSYNC IN VCO ADJ AFC DET
SDATA
NRGB
GND2
SCLK
VCC1
VDIN
VSS
48
47
46
45
44
43
42
41
40 REG
39
38 LOGIC
37
36
35
34
33 LOGIC
PONRST 49 COMDC 50 SECAM BLACK ADJ 51 YIN 52 CTRAP OUT 53 CTRAP IN 54 Y DET 55 ACC DET 56 C IN 57 VCC1 58 GND3 59 KILL DET 60 APC DET 61 SC OUT 62 VXO-NTSC 63
LOGIC DAC DAC CLAMP SW
LOGIC IICBUS SYNCSEPA VCO I/N 32 HDOUT 31 VDOUT HHKILL VSYNC DROP PHASE COMP F DET PWM 30 PWM OUT 29 VCC3 VCOM VERT. COUNT 28 VCOM OUT
SYNC CUT ACC DET BPF
DELAY INVERT SHARPNESS ACC AMP GCA R-Y,B-Y DEMOD GAMMA LIMIT
SCP
POL
27 R-OUT DET 26 R-OUT 25 VCC2 24 VREF DRIV
CONTRAST
23 GND1 22 G-OUT DET
BRIGHT APC LOGIC YUV SW KILLER INT/EXT SW CLAMP G-Y GEME
21 G-OUT
GCA
MATRIX
OSD SW
20 B-OUT DET 19 B-OUT 18 BLAK 17 YS
VXO GENE VXO
VXO-PAL 64 1
PLAN
REG 2
R-Y OUT
3
B-Y OUT
4
R-Y IN
5
B-Y IN
6
VCC1
7
VREF
8
R-IN1
9
G-IN1
10
B-IN1
11
R-DET
12
G-DET
13
B-DET
14
R-IN2
15
G-IN2
16
B-IN2
IC350 TA2061AF
AGC-T/C FO-SW VREFC LOUT
9 BUFFER BUFFER 8
16
15
14
13 LEVEL DET
12
11
FO-R
AGC
VCC
LIN
10
VREF
AGC
PRE EMPHASIS LOUT=L+K·(L-R)
VCO
ROUT=R-K·(L-R) AGC PRE EMPHASIS VCO
LEVEL DET
O.S.M
1
2
3
4
5
6
7
AUTO-OFF
MIX-NF
SURND
ROUT
RIN
GND
FO-L
31
XVM-R70
IC401 µPD6467GR-546-E1
CLK 1 CS 2 DATA 3
DATA INPUT SHIFT REGISTER
20 H SYNC 19 V SYNC INSTRUCTION DECODER CONTROL SIGNALS
PCL 4 DISPLAY CONTROL REGISTER CHARACTER SIZE REGISTER H-ADDRESS REGISTER WRITE-IN ADDRESS COUNTER DATA SELECT VDD 5 CMDCT 6 18 17 16 15 14 13 12 11 VR VG VB V BLK VC2 BLK2 VC2 BLK1 V-SIZE COUNTER H-POSITION COUNTER H-ADDRESS COUNTER VIDEO RAM BACK INTERRUPT DATA REGISTER
OSC OSC IN 8 TEST 9 GND 10 H-SIZE COUNTER V-POSITION COUNTER V-ADDRESS COUNTER V-AD REGISTER CHARACTER GENERATOR ROM 12X16BITX 512-WORD
SYNC PROTECTION
IC501 CD74HCT4053
VCC BN AN
A1
A0
S0
S1
16
15
14
13
12
11 LOGIC LEVEL CONVERSION
10 LOGIC LEVEL CONVERSION
TG
TG
LOGIC LEVEL CONVERSION
BINART TO 1 OF 2 DECODER
BINART TO 1 OF 2 DECODER
BINART TO 1 OF 2 DECODER
TG
TG
TG
TG
LOGIC LEVEL CONVERSION
1 B1
2 B0
3 C1
4 CN
5 C0
6 E
7 VEE
32
GND
S2
9
8
OUTPUT CONTROL
OSC OUT 7
CHARACTER DATA COLOR DATA PRINTER DATA REVERSE DATA OUTPUT DATA
XVM-R70
IC600 TC200G02AF-0104
SPL VDD OSC1 SCK VSS SIZE XCK1 TST4 TST3 TST2 TST1 SVSEP XCKE VDD
48 47
VSS LPF1
46 45 44 43 42 41 40 39 38 37 36 35 34 33
VDD PDOS TSTB VSS STH1 STH2 VSS HDIR CHP2 VDD CPH1 VSS CPH3 VSS SCKE VDD
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
MASK
PD H-OUT
OSC
H-COUNTER
V-COUNTER
V-OUT V-SEP FIELD DISCRI INT/EXT SEL
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
STV2 NGEO1 NGEO2 NGEO3 CPV CX VDD STV1 HSRV RV NHD NVD VSS PAL MIRROR UPSD
1 2 3 4
HPOS1 HPOS2 HPOS3 HPOS4
5 6 7 8 9 10 11 12 13 14 15 16
HODE1 HODE2 HODE3 NBLK NDSH VSS NDSV NCLP POLS POLC COMPS VDD
IC601 NJU7071V
OFF SET IN2
VDD
8
7
OUT
NC
6
5
1
OFF SET IN1
2
IN-
3
IN+
4
VSS
33
XVM-R70 SECTION 7 EXPLODED VIEWS
NOTE: · The mechanical parts with no reference number in the exploded views are not supplied. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · -XX and -X mean standardized parts, so they may have some difference from the original one. · Abbreviation CND : Canadian model · Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet's Color · Accessories are given in the last of this parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
7-1. BASE (1) SECTION
#1 #1
1
2
not supplied
#2
not supplied
#2 #2 #1 #3 #2 #3
3
#3 #3
Ref. No. 1 2 3
Part No.
Description
Remark
Ref. No. #1 #2 #3
Part No.
Description
Remark
3-254-853-01 COVER (HINGE FRONT) 3-254-854-01 COVER (HINGE REAR) 3-254-874-01 SKIRT (BASE)
7-682-649-01 SCREW PS 3X10 7-685-534-14 SCREW +BTP 2.6X8 TYPE2 N-S 7-685-504-19 SCREW +B 2X6 TYPE2 N-S
34
XVM-R70
7-2. BASE (2) SECTION
58 57 52 53 54
not supplied #1 not supplied not supplied
not supplied (SW board)
#6
59
not supplied
#1
not supplied
#1 #5
#1
#2
not supplied
56
not supplied
52 53 55 54
#4
51
not supplied #4 #2 #2 #2 #2
Ref. No. 51 52 53 54 55 56 57
Part No. A-3274-916-A 3-254-851-01 3-254-857-01 3-254-848-01 3-254-847-01
Description BASE BOARD, COMPLETE CUSHION (LIFT) LIFT (OPEN) SPRING (LIFT), COMPRESSION SPRING (HOOK), COMPRESSION
Remark
Ref. No. 58 59 #1 #2 #4 #5 #6
Part No. 3-254-855-01 X-3383-606-1 7-682-649-01 7-685-534-14 7-685-132-19
Description BUTTON (OPEN) MONITOR SUB ASSY, BASE SCREW PS 3X10 SCREW +BTP 2.6X8 TYPE2 N-S SCREW +PTPWH 2.6X5 (TYPE2)
Remark
3-254-856-01 HOOK (OPEN) 3-254-846-01 SPRING (OPEN), COMPRESSION
7-621-255-35 SCREW +P 2X5 7-621-773-95 SCREW +B 2.6X6
35
XVM-R70
7-3. LCD SECTION
107
#5 #5
108
#7
112
A
#3 #5
110
#6 #6 #6
106
B
109 104 105
#3 #5 #5
A
#6 not supplied
109
104
#3 LCD1
114
#3
113 104 103
#7
#7
B
not supplied
#7
102
#7
111
101
Ref. No. 101 102 103 104 105 106 107 108 109 110
Part No. 3-254-861-01 A-3274-919-A 3-254-862-01 3-254-866-01 3-254-862-11 3-254-860-01 4-969-961-11 3-254-863-01 3-254-868-01 3-254-869-01
Description CASE (LCD REAR) LCD BOARD, COMPLETE BUTTON (FUNCTION) RETAINER (LCD) BUTTON (FUNCTION) CASE (LCD FRONT) EMBLEM (NO.4), SONY WINDOW (IR) CUSHION (LCD) HINGE
Remark
Ref. No. 111 112 113 114 * LCD1
Part No. 1-827-343-11 3-256-961-01 3-257-670-01 3-255-912-01 1-805-280-11
Description
Remark
CORD (WITH CONNECTOR) RETAINER (LCD.B) TERMINAL (LCD) SHEET (B), SHIELD DISPLAY PANEL, LIQUID CRYSTAL (TFT) (7 in. WIDE) SCREW +B 2X6 TYPE2 N-S SCREW +P 2X5 SCREW +B 2.6X6 SCREW +P 2X8 TYPE2 NON-SLIT
#3 #5 #6 #7
7-685-504-19 7-621-255-35 7-621-773-95 7-685-105-19
36
XVM-R70
7-4. CONNECTION BOX SECTION (XA-115)
151
not supplied
not supplied not supplied CN202 not supplied CN300 J200 J300 CN301 CN901
J201 CN201 CN200 J901 not supplied
not supplied not supplied not supplied
Ref. No. 151 CN200 CN201 CN202 CN300 CN301
Part No. 1-478-044-11 9-885-035-44 9-885-035-98 9-885-035-45 9-885-035-46
Description
Remark
Ref. No. CN901 J200 J201 J300 J901
Part No. 9-885-035-48 9-885-035-49 9-885-035-49 9-885-035-50 9-885-035-51
Description CONNECTOR 4P JACK, HEADPHONE JACK, HEADPHONE JACK, DATA (OUT) JACK, POWER (PS USE)
Remark
CONNECTION BOX (XA-115) JACK, PIN 6P (AUDIO/VIDEO INPUT) JACK, PIN 3P (R) (AUDIO/VIDEO INPUT) JACK, PIN 3P (Y) (AUDIO/VIDEO OUT) CONNECTOR 13P (DVD)
9-885-035-47 CONNECTOR 22P
37
XVM-R70 BASE
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX and -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable · Abbreviation CND : Canadian model Ref. No. Part No. Description
SECTION 8 ELECTRICAL PARTS LIST
· Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. · CAPACITORS uF : µF · COILS uH : µH The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board. Remark Ref. No. Q954 Q956 Q957 Q958 10% 20% 20% 10% 20% 10% 20% 10% 10% 20% 20% 16V 25V 25V 10V 16V 25V 35V 25V 25V 16V 25V Part No. 8-729-905-35 8-729-056-58 8-729-056-58 8-729-402-13 Description TRANSISTOR 2SC4081-R FET TPC6102(TE85R) FET TPC6102(TE85R) TRANSISTOR XN1501 < RESISTOR > R950 R951 R952 R954 R955 R956 R957 R958 R959 R960 R962 R965 R966 R967 R968 R969 R970 R971 R972 R973 R974 R975 R976 R977 1-216-843-11 1-218-736-11 1-218-722-11 1-218-720-11 1-218-724-11 1-216-847-11 1-216-845-11 1-216-833-11 1-216-847-11 1-216-847-11 1-216-829-11 1-216-837-11 1-216-847-11 1-216-847-11 1-216-843-11 1-216-835-11 1-216-847-11 1-216-841-11 1-216-864-11 1-216-829-11 1-216-845-11 1-216-833-11 1-220-277-11 1-220-277-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SQUARE CHIP SQUARE CHIP < SWITCH > 68K 68K 18K 15K 22K 150K 100K 10K 150K 150K 4.7K 22K 150K 150K 68K 15K 150K 47K 0 4.7K 100K 10K 2.2K 2.2K 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/4W 1/4W Remark
A-3274-916-A BASE BOARD, COMPLETE ********************* < CAPACITOR > C950 C951 C952 C953 C955 C956 C957 C958 C959 C960 C961 1-107-826-11 1-100-638-11 1-100-638-11 1-165-908-11 1-126-396-11 1-164-298-11 1-126-399-11 1-164-298-11 1-164-298-11 1-126-396-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 1000uF 1000uF 1uF 47uF 0.15uF 10uF 0.15uF 0.15uF 47uF 1000uF
1-100-638-11 ELECT < CONNECTOR >
CN950 CN951 * CN952 CN953 * CN954 * CN955
1-794-270-11 1-774-935-11 1-695-441-21 1-695-440-21 1-691-741-21
CONNECTOR 22P PIN, CONNECTOR (PC BOARD) 12P PIN, CONNECTOR (PC BOARD) 7P PIN, CONNECTOR (PC BOARD) 6P PIN, CONNECTOR (PC BOARD) 2P
1-691-741-21 PIN, CONNECTOR (PC BOARD) 2P < DIODE >
D901 D902 D903
8-719-083-71 DIODE UDZS-TE17-30B 8-719-044-76 DIODE 1SS356-TW11 8-719-044-76 DIODE 1SS356-TW11 < FUSE >
0 F950
1-576-410-21 FUSE, CHIP (2A) < IC > S950 S951 1-571-277-51 SWITCH, SLIDE (POWER SELECT) 1-762-196-21 SWITCH, TACTILE (RESET) < THERMISTOR (POSITIVE) > TH950 < COIL > < VARISTOR > 1-804-777-21 THERMISTOR, POSITIVE
IC952 IC953
6-704-268-01 IC XC6206P332MR 6-704-684-01 IC TA78DL05AF-TE16L
L950 L951
1-456-437-21 COIL, CHOKE 1-412-951-11 INDUCTOR < TRANSISTOR >
100uH 10uH
VDR950 1-801-866-11 VARISTOR ERZV14D220 *************************************************************
Q951 Q952
8-729-905-35 TRANSISTOR 2SC4081-R 8-729-056-58 FET TPC6102(TE85R)
38
XVM-R70 LCD
Ref. No. Part No. Description Remark Ref. No. C513 C514 C515 C516 C517 C518 C519 C520 C521 C522 C523 C524 C525 C526 C527 C528 C529 C530 C531 C532 C533 C534 C535 C536 C537 C538 C539 C540 C541 C542 C543 C544 C545 C546 C547 C548 C600 C601 C602 C603 C604 C605 C606 C607 C608 C609 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 Part No. 1-126-396-11 1-104-915-11 1-104-915-11 1-162-970-11 1-107-826-11 1-104-915-11 1-162-977-11 1-165-908-11 1-126-396-11 1-164-227-11 1-119-751-11 1-135-145-11 1-164-227-11 1-165-908-11 1-119-751-11 1-162-965-11 1-135-210-11 1-107-826-11 1-135-834-11 1-135-210-11 1-162-920-11 1-162-916-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-135-177-21 1-164-227-11 1-162-920-11 1-164-238-11 1-107-826-11 1-165-908-11 1-165-908-11 1-165-908-11 1-126-168-11 1-165-908-11 1-165-908-11 1-107-826-11 1-126-396-11 1-165-908-11 1-107-826-11 1-126-396-11 1-165-908-11 1-107-826-11 1-107-826-11 1-107-826-11 1-165-908-11 1-107-826-11 1-162-924-11 1-162-927-11 1-162-964-11 1-119-751-11 1-107-826-11 1-107-826-11 Description ELECT CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP 47uF 2.2uF 2.2uF 0.01uF 0.1uF 2.2uF 0.0018uF 1uF 47uF 0.022uF 22uF 0.47uF 0.022uF 1uF 22uF 0.0015uF 4.7uF 0.1uF 2.2uF 4.7uF 27PF 12PF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 1uF 0.022uF 27PF 36PF 0.1uF 1uF 1uF 1uF 1000uF 1uF 1uF 0.1uF 47uF 1uF 0.1uF 47uF 1uF 0.1uF 0.1uF 0.1uF 1uF 0.1uF 56PF 100PF 0.001uF 22uF 0.1uF 0.1uF 680PF 0.1uF 0.1uF 20% 20% 20% 10% 10% 20% 10% 10% 20% 10% 20% 10% 10% 10% 20% 10% 20% 10% 20% 5% 5% 10% 10% 10% 10% 10% 20% 10% 5% 5% 10% 10% 10% 10% 20% 10% 10% 10% 20% 10% 10% 20% 10% 10% 10% 10% 10% 10% 5% 5% 10% 20% 10% 10% 5% 10% 10% Remark 16V 16V 16V 25V 16V 16V 50V 10V 16V 25V 16V 35V 25V 10V 16V 50V 10V 16V 6.3V 10V 50V 50V 16V 16V 16V 16V 16V 20V 25V 50V 50V 16V 10V 10V 10V 6.3V 10V 10V 16V 16V 10V 16V 16V 10V 16V 16V 16V 10V 16V 50V 50V 50V 16V 16V 16V 25V 16V 16V A-3274-919-A LCD BOARD, COMPLETE ******************** 1-827-343-11 CORD (WITH CONNECTOR) < CAPACITOR > C350 C351 C352 C353 C354 C355 C356 C357 C358 C359 C360 C361 C362 C363 C364 C400 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C422 C423 C424 C425 C426 C500 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C511 C512 1-107-826-11 1-135-366-11 1-164-298-11 1-137-942-21 1-126-401-21 1-126-401-21 1-107-826-11 1-137-893-11 1-107-826-11 1-126-394-11 1-107-826-11 1-126-396-11 1-107-826-11 1-126-396-11 1-126-401-21 1-165-908-11 1-107-826-11 1-126-396-11 1-165-908-11 1-107-826-11 1-107-826-11 1-162-918-11 1-162-918-11 1-126-394-11 1-164-004-11 1-107-826-11 1-107-826-11 1-126-394-11 1-107-826-11 1-126-394-11 1-162-910-11 1-162-921-11 1-162-921-11 1-107-826-11 1-162-970-11 1-117-579-11 1-162-968-11 1-162-964-11 1-162-927-11 1-126-396-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-104-915-11 1-107-826-11 1-107-826-11 1-107-826-11 1-126-401-21 CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT CHIP ELECT CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP DOUBLE LAYERS CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 100uF 0.15uF 47uF 1uF 1uF 0.1uF 22uF 0.1uF 10uF 0.1uF 47uF 0.1uF 47uF 1uF 1uF 0.1uF 47uF 1uF 0.1uF 0.1uF 18PF 18PF 10uF 0.1uF 0.1uF 0.1uF 10uF 0.1uF 10uF 5PF 33PF 33PF 0.1uF 0.01uF 0.1F 0.0047uF 0.001uF 100PF 47uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 2.2uF 0.1uF 0.1uF 0.1uF 1uF 1uF 1uF 10% 20% 10% 20% 20% 20% 10% 20% 10% 20% 10% 20% 10% 20% 20% 10% 10% 20% 10% 10% 10% 5% 5% 20% 10% 10% 10% 20% 10% 20% 0.25PF 5% 5% 10% 10% 16V 16V 25V 25V 50V 50V 16V 16V 16V 16V 16V 16V 16V 16V 50V 10V 16V 16V 10V 16V 16V 50V 50V 16V 25V 16V 16V 16V 16V 16V 50V 50V 50V 16V 25V 35V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 16V 16V 16V 50V 50V 50V
10% 10% 5% 20% 10% 10% 10% 10% 10% 20% 10% 10% 10% 20% 20% 20%
1-126-401-21 ELECT CHIP 1-126-401-21 ELECT CHIP
1-115-412-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP
39
XVM-R70 LCD
Ref. No. C626 C627 C628 C800 C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 C835 C836 C837 C838 C850 C851 C855 C857 C858 C859 C860 C861 C862 C865 C866 C867 Part No. 1-125-891-11 1-162-970-11 1-162-970-11 1-164-315-11 1-164-315-11 1-137-980-11 1-164-315-11 1-164-298-11 1-137-942-21 1-164-298-11 1-137-942-21 1-125-891-11 1-164-315-11 1-137-980-11 1-137-942-21 1-107-826-11 1-107-826-11 1-137-942-21 1-107-826-11 1-127-820-11 1-126-394-11 1-164-298-11 1-137-942-21 1-137-942-21 1-164-298-11 1-137-942-21 1-137-942-21 1-164-298-11 1-137-942-21 1-137-942-21 1-164-298-11 1-137-942-21 1-137-942-21 1-137-942-21 1-107-826-11 1-137-942-21 1-107-826-11 1-137-942-21 1-107-826-11 1-137-942-21 1-164-298-11 1-100-155-11 1-137-942-21 1-128-536-11 1-100-639-21 1-115-156-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-964-11 1-107-826-11 1-137-894-21 1-128-536-11 1-128-536-11 Description CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT CHIP MYLAR CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP ELECT CHIP < CONNECTOR > CN401 CN403 1-774-935-11 PIN, CONNECTOR (PC BOARD) 12P 1-695-440-21 PIN, CONNECTOR (PC BOARD) 6P 0.47uF 0.01uF 0.01uF 470PF 470PF 0.47uF 470PF 0.15uF 47uF 0.15uF 47uF 0.47uF 470PF 0.47uF 47uF 0.1uF 0.1uF 47uF 0.1uF 4.7uF 10uF 0.15uF 47uF 47uF 0.15uF 47uF 47uF 0.15uF 47uF 47uF 0.15uF 47uF 47uF 47uF 0.1uF 47uF 0.1uF 47uF 0.1uF 47uF 0.15uF 470PF 47uF 100uF 0.1uF 1uF 0.1uF 0.1uF 0.1uF 0.001uF 0.1uF 470uF 100uF 100uF 10% 10% 10% 5% 5% 10% 5% 10% 20% 10% 20% 10% 5% 10% 20% 10% 10% 20% 10% Remark 10V 25V 25V 50V 50V 50V 50V 25V 25V 25V 25V 10V 50V 50V 25V 16V 16V 25V 16V 16V 16V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 16V 25V 16V 25V 16V 25V 25V 100V 25V 25V 100V 10V 16V 16V 16V 50V 16V 25V 25V 25V Ref. No. * CN404 CN800 CN850 * CN902 Part No. 1-691-741-21 1-794-237-21 1-815-494-21 1-695-441-21 Description PIN, CONNECTOR (PC BOARD) 2P CONNECTOR, FFC/FPC 30P PIN, CONNECTOR 2P PIN, CONNECTOR (PC BOARD) 7P < DIODE > D350 D351 D352 D353 D354 D355 D356 D400 D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D412 D500 D501 D600 D601 D602 D603 D604 D800 D801 D802 D803 D804 D805 D852 D853 D854 D855 6-500-660-01 6-500-660-01 6-500-660-01 6-500-660-01 6-500-660-01 6-500-660-01 8-719-044-76 8-719-069-55 8-719-069-55 8-719-069-55 8-719-069-55 8-719-069-55 8-719-069-55 8-719-069-55 8-719-044-76 8-719-044-76 8-719-017-62 8-719-058-24 8-719-017-62 8-719-058-24 8-719-044-76 8-719-048-98 8-719-069-54 8-719-027-74 8-719-069-54 8-719-987-69 8-719-044-76 8-719-988-78 8-719-052-18 8-719-048-98 8-719-048-98 8-719-044-76 8-719-044-76 8-719-052-18 8-719-987-69 LED LED LED LED LED SIR-568ST3F (LCD BACK LIGHT) SIR-568ST3F (LCD BACK LIGHT) SIR-568ST3F (LCD BACK LIGHT) SIR-568ST3F (LCD BACK LIGHT) SIR-568ST3F (LCD BACK LIGHT) Remark
LED SIR-568ST3F (LCD BACK LIGHT) DIODE 1SS356-TW11 DIODE UDZS-TE17-5.6B DIODE UDZS-TE17-5.6B DIODE UDZS-TE17-5.6B DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE UDZS-TE17-5.6B