Text preview for : 89c4051.pdf part of ATMEL 89C4051 8-Bit Microcontoller with 4K Bytes flash
Back to : 89c4051.pdf | Home
Features
· Compatible with MCS-51TM Products · 4K Bytes of Reprogrammable Flash Memory · · · · · · · · · · · ·
Endurance: 1,000 Write/Erase Cycles 3.0V to 6V Operating Range Fully Static Operation: 0 Hz to 24 MHz Two-Level Program Memory Lock 128 x 8-Bit Internal RAM 15 Programmable I/O Lines Two 16-Bit Timer/Counters Six Interrupt Sources Programmable Serial UART Channel Direct LED Drive Outputs On-Chip Analog Comparator Low Power Idle and Power Down Modes Brown-Out Detection
8-Bit Microcontroller with 4K Bytes Flash AT89C4051 Preliminary
Description
The AT89C4051 is a low-voltage, high-performance CMOS 8-bit microcomputer with 4K Bytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmel's high density nonvolatile memory technology and is compatible with the industry standard MCS-51TM instruction set. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C4051 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications. The AT89C4051 provides the following standard features: 4K Bytes of Flash, 128 bytes of RAM, 15 I/O lines, two 16-bit timer/counters, a five vector two-level interrupt architecture, a full duplex serial port, a precision analog comparator, on-chip oscillator and clock circuitry. In addition, the AT89C4051 is designed with static logic for operation down to zero frequency and supports two software-selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power Down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset.
Pin Configuration
PDIP/SOIC
/VPP
Rev. 1001A02/98
1
Block Diagram
2
AT89C4051
AT89C4051
Pin Description
VCC Supply voltage. GND Ground. Port 1 Port 1 is an 8-bit bidirectional I/O port. Port pins P1.2 to P1.7 provide internal pullups. P1.0 and P1.1 require external pullups. P1.0 and P1.1 also serve as the positive input (AIN0) and the negative input (AIN1), respectively, of the on-chip precision analog comparator. The Port 1 output buffers can sink 20 mA and can drive LED displays directly. When 1s are written to Port 1 pins, they can be used as inputs. When pins P1.2 to P1.7 are used as inputs and are externally pulled low, they will source current (IIL) because of the internal pullups. Port 1 also receives code data during Flash programming and verification. Port 3 Port 3 pins P3.0 to P3.5, P3.7 are seven bidirectional I/O pins with internal pullups. P3.6 is hard-wired as an input to the output of the on-chip comparator and is not accessible as a general purpose I/O pin. The Port 3 output buffers can sink 20 mA. When 1s are written to Port 3 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pullups. Port 3 also serves the functions of various special features of the AT89C4051 as listed below:
Port Pin P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 Alternate Functions RXD (serial input port) TXD (serial output port) INT0 (external interrupt 0) INT1 (external interrupt 1) T0 (timer 0 external input) T1 (timer 1 external input) Note: C1, C2 = 30 pF ± 10 pF for Crystals = 40 pF ± 10 pF for Ceramic Resonators
XTAL2 Output from the inverting oscillator amplifier.
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 1. Either a quartz crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 2. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed. Figure 1. Oscillator Connections
Figure 2. External Clock Drive Configuration
Port 3 also receives some control signals for Flash programming and verification. RST Reset input. All I/O pins are reset to 1s as soon as RST goes high. Holding the RST pin high for two machine cycles while the oscillator is running resets the device. Each machine cycle takes 12 oscillator or clock cycles. XTAL1 Input to the inverting oscillator amplifier and input to the internal clock operating circuit.
3
Special Function Registers
A map of the on-chip memory area called the Special Function Register (SFR) space is shown in the table below. Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. Table 1. AT89C4051 SFR Map and Reset Values
0F8H 0F0H 0E8H 0E0H 0D8H 0D0H 0C8H 0C0H 0B8H 0B0H 0A8H 0A0H 98H 90H 88H 80H SCON 00000000 P1 11111111 TCON 00000000 TMOD 00000000 SP 00000111 TL0 00000000 DPL 00000000 TL1 00000000 DPH 00000000 TH0 00000000 TH1 00000000 PCON 0XXX0000 SBUF XXXXXXXX IP XXX00000 P3 11111111 IE 0XX00000 PSW 00000000 ACC 00000000 B 00000000 0FFH 0F7H 0EFH 0E7H 0DFH 0D7H 0CFH 0C7H 0BFH 0B7H 0AFH 0A7H 9FH 97H 8FH 87H
User software should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In that case, the reset or inactive values of the new bits will always be 0.
4
AT89C4051
AT89C4051
Restrictions on Certain Instructions
The AT89C4051 is an economical and cost-effective member of Atmel's growing family of microcontrollers. It contains 4K bytes of flash program memory. It is fully compatible with the MCS-51 architecture, and can be programmed using the MCS-51 instruction set. However, there are a few considerations one must keep in mind when utilizing certain instructions to program this device. All the instructions related to jumping or branching should be restricted such that the destination address falls within the physical program memory space of the device, which is 4K for the AT89C4051. This should be the responsibility of the software programmer. For example, LJMP 0FE0H would be a valid instruction for the AT89C4051 (with 4K of memory), whereas LJMP 1000H would not. 1. Branching instructions: LCALL, LJMP, ACALL, AJMP, SJMP, JMP @A+DPTR These unconditional branching instructions will execute correctly as long as the programmer keeps in mind that the destination branching address must fall within the physical boundaries of the program memory size (locations 00H to FFFH for the 89C4051). Violating the physical space limits may cause unknown program behavior. CJNE [...], DJNZ [...], JB, JNB, JC, JNC, JBC, JZ, JNZ With these conditional branching instructions the same rule above applies. Again, violating the memory boundaries may cause erratic execution. For applications involving interrupts the normal interrupt service routine address locations of the 80C51 family architecture have been preserved. 2. MOVX-related instructions, Data Memory: The AT89C4051 contains 128 bytes of internal data memory. Thus, in the AT89C4051 the stack depth is limited to 128 bytes, the amount of available RAM. External DATA memory access is not supported in this device, nor is external PROGRAM memory execution. Therefore, no MOVX [...] instructions should be included in the program. A typical 80C51 assembler will still assemble instructions, even if they are written in violation of the restrictions mentioned above. It is the responsibility of the controller user to know the physical features and limitations of the device being used and adjust the instructions used correspondingly.
Program Memory Lock Bits
On the chip are two lock bits which can be left unprogrammed (U) or can be programmed (P) to obtain the additional features listed in the table below:
Lock Bit Protection Modes(1)
Program Lock Bits LB1 1 2 3 Note: U P P LB2 U U P Protection Type No program lock features. Further programming of the Flash is disabled. Same as mode 2, also verify is disabled.
1. The Lock Bits can only be erased with the Chip Erase operation.
Idle Mode
In idle mode, the CPU puts itself to sleep while all the onchip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special functions registers remain unchanged during this mode. The idle mode can be terminated by any enabled interrupt or by a hardware reset. P1.0 and P1.1 should be set to '0' if no external pullups are used, or set to '1' if external pullups are used. It should be noted that when idle is terminated by a hardware reset, the device normally resumes program execution, from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a port pin when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory.
Power Down Mode
In the power down mode the oscillator is stopped, and the instruction that invokes power down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the power down mode is terminated. The only exit from power down is a hardware reset. Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be activated before V CC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize. P1.0 and P1.1 should be set to '0' if no external pullups are used, or set to '1' if external pullups are used.
5
Brown-Out Detection
When V CC drops below the detection threshold, all port pins (except P1.0 and P1.1) are weakly pulled high. When
VCC 2.3V
VCC goes back up again, an internal Reset is automatically generated after a delay of typically 15 msec. The nominal brown-out detection threshold is 2.3V ± 10%.
2.3V
PORT PIN INTERNAL RESET 15 msec.
Programming The Flash
The AT89C4051 is shipped with the 4K bytes of on-chip PEROM code memory array in the erased state (i.e., contents = FFH) and ready to be programmed. The code memory array is programmed one byte at a time. Once the array is programmed, to re-program any non-blank byte, the entire memory array needs to be erased electrically. Internal Address Counter: The AT89C4051 contains an internal PEROM address counter which is always reset to 000H on the rising edge of RST and is advanced by applying a positive going pulse to pin XTAL1. Programming Algorithm: To program the AT89C4051, the following sequence is recommended. 1. Power-up sequence: Apply power between VCC and GND pins Set RST and XTAL1 to GND 2. Set pin RST to 'H' Set pin P3.2 to 'H' 3. Apply the appropriate combination of 'H' or 'L' logic levels to pins P3.3, P3.4, P3.5, P3.7 to select one of the programming operations shown in the PEROM Programming Modes table. To Program and Verify the Array: 4. Apply data for Code byte at location 000H to P1.0 to P1.7. 5. Raise RST to 12V to enable programming. 6. Pulse P3.2 once to program a byte in the PEROM array or the lock bits. The byte-write cycle is self-timed and typically takes 1.2 ms. 7. To verify the programmed data, lower RST from 12V to logic 'H' level and set pins P3.3 to P3.7 to the appropriate levels. Output data can be read at the port P1 pins. 8. To program a byte at the next address location, pulse XTAL1 pin once to advance the internal address counter. Apply new data to the port P1 pins. 9. Repeat steps 5 through 8, changing data and advancing the address counter for the entire 4K bytes array or until the end of the object file is reached. 10.Power-off sequence: set XTAL1 to 'L' set RST to 'L' Turn VCC power off Data Polling: The AT89C4051 features Data Polling to indicate the end of a write cycle. During a write cycle, an attempted read of the last byte written will result in the complement of the written data on P1.7. Once the write cycle has been completed, true data is valid on all outputs, and the next cycle may begin. Data Polling may begin any time after a write cycle has been initiated. Ready/Busy: The Progress of byte programming can also be monitored by the RDY/BSY output signal. Pin P3.1 is pulled low after P3.2 goes High during programming to indicate BUSY. P3.1 is pulled High again when programming is done to indicate READY. Program Verify: If lock bits LB1 and LB2 have not been programmed code data can be read back via the data lines for verification: 1. Reset the internal address counter to 000H by bringing RST from 'L' to 'H'. 2. Apply the appropriate control signals for Read Code data and read the output data at the port P1 pins. 3. Pulse pin XTAL1 once to advance the internal address counter. 4. Read the next code data byte at the port P1 pins. 5. Repeat steps 3 and 4 until the entire array is read. The lock bits cannot be verified directly. Verification of the lock bits is achieved by observing that their features are enabled. Chip Erase: The entire PEROM array (4K bytes) and the two Lock Bits are erased electrically by using the proper combination of control signals and by holding P3.2 low for 10 ms. The code array is written with all "1"s in the Chip Erase operation and must be executed before any nonblank memory byte can be re-programmed.
6
AT89C4051
AT89C4051
Reading the Signature Bytes: The signature bytes are read by the same procedure as a normal verification of locations 000H, 001H, and 002H, except that P3.5 and P3.7 must be pulled to a logic low. The values returned are as follows. (000H) = 1EH indicates manufactured by Atmel (001H) = 41H indicates 89C4051
Programming Interface
Every code byte in the Flash array can be written and the entire array can be erased by using the appropriate combination of control signals. The write operation cycle is selftimed and once initiated, will automatically time itself to completion. All major programming vendors offer worldwide support for the Atmel microcontroller series. Please contact your local programming vendor for the appropriate software revision.
Flash Programming Modes
Mode Write Code Data(1)(3) RST/VPP 12V P3.2/PROG P3.3 L P3.4 H P3.5 H P3.7 H
Read Code Data(1) Write Lock Bit - 1
H 12V
H
L H
L H
H H
H H
Bit - 2
12V
H
H
L
L
Chip Erase
12V
(2)
H
L
L
L
Read Signature Byte Notes:
H
H
L
L
L
L
1. The internal PEROM address counter is reset to 000H on the rising edge of RST and is advanced by a positive pulse at XTAL 1 pin. 2. Chip Erase requires a 10-ms PROG pulse. 3. P3.1 is pulled Low during programming to indicate RDY/BSY.
7
Figure 3. Programming the Flash Memory
AT89C4051
Figure 4. Verifying the Flash Memory
AT89C4051
PP
Flash Programming and Verification Characteristics
TA = 0°C to 70°C, VCC = 5.0 ± 10%
Symbol VPP IPP tDVGL tGHDX tEHSH tSHGL tGHSL tGLGH tELQV tEHQZ tGHBL tWC tBHIH tIHIL Note: 1. Parameter Programming Enable Voltage Programming Enable Current Data Setup to PROG Low Data Hold After PROG P3.4 (ENABLE) High to VPP VPP Setup to PROG Low VPP Hold After PROG PROG Width ENABLE Low to Data Valid Data Float After ENABLE PROG High to BUSY Low Byte Write Cycle Time RDY/BSY\ to Increment Clock Delay Increment Clock High Only used in 12-volt programming mode. 1.0 200 0 1.0 1.0 1.0 10 10 1 110 1.0 1.0 50 2.0 Min 11.5 Max 12.5 250 Units V µA µs µs µs µs µs µs µs µs ns ms µs ns
8
AT89C4051
AT89C4051
Flash Programming and Verification Waveforms
Absolute Maximum Ratings*
Operating Temperature ................................. -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground .....................................-1.0V to +7.0V Maximum Operating Voltage............................................. 6.6V DC Output Current...................................................... 25.0 mA *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
9
DC Characteristics
TA = -40°C to 85°C, VCC = 3.0V to 6.0V (unless otherwise noted)
Symbol VIL VIH VIH1 VOL VOH Parameter Input Low Voltage Input High Voltage Input High Voltage Output Low (Ports 1, 3) Voltage(1) (Except XTAL1, RST) (XTAL1, RST) IOL = 20 mA, VCC = 5V IOL = 10 mA, VCC = 2.7V IOH = -80 µA, VCC = 5V ± 10% IOH = -30 µA IOH = -12 µA IIL ITL ILI VOS VCM RRST CIO ICC Logical 0 Input Current (Ports 1, 3) Logical 1 to 0 Transition Current (Ports 1, 3) Input Leakage Current (Port P1.0, P1.1) Comparator Input Offset Voltage Comparator Input Common Mode Voltage Reset Pulldown Resistor Pin Capacitance Power Supply Current Test Freq. = 1 MHz, TA = 25°C Active Mode, 12 MHz, VCC = 6V/3V Idle Mode, 12 MHz, VCC = 6V/3V P1.0 & P1.1 = 0V or VCC Power Down Mode(2) VCC = 6V P1.0 & P1.1 = 0V or VCC VCC = 3V P1.0 & P1.1 = 0V or VCC Notes: VIN = 0.45V VIN = 2V, VCC = 5V ± 10% 0 < VIN < VCC VCC = 5V 0 50 2.4 0.75 VCC 0.9 VCC -50 -750 ±10 20 VCC 300 10 15/5.5 5/1 100 20 Condition Min -0.5 0.2 VCC + 0.9 0.7 VCC Max 0.2 VCC - 0.1 VCC + 0.5 VCC + 0.5 0.5 Units V V V V V V V µA µA µA mV V K pF mA mA µA µA
Output High Voltage (Ports 1, 3)
1. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 20 mA Maximum total IOL for all output pins: 80 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 2. Minimum VCC for Power Down is 2V.
10
AT89C4051
External Clock Drive Waveforms
External Clock Drive
Symbol Parameter VCC = 3.0V to 6.0V Min 1/tCLCL tCLCL tCHCX tCLCX tCLCH tCHCL Oscillator Frequency Clock Period High Time Low Time Rise Time Fall Time 0 83.3 30 30 20 20 Max 12 VCC = 4.0V to 6.0V Min 0 41.6 15 15 20 20 Max 24 MHz ns ns ns ns ns Units
11
AT89C4051
AT89C4051
Serial Port Timing: Shift Register Mode Test Conditions
(VCC = 5.0V ± 20%; Load Capacitance = 80 pF)
Symbol Parameter 12 MHz Osc Min tXLXL tQVXH tXHQX tXHDX tXHDV Serial Port Clock Cycle Time Output Data Setup to Clock Rising Edge Output Data Hold After Clock Rising Edge Input Data Hold After Clock Rising Edge Clock Rising Edge to Input Data Valid 1.0 700 50 0 700 Max Variable Oscillator Min 12tCLCL 10tCLCL-133 2tCLCL-117 0 10tCLCL-133 Max µs ns ns ns ns Units
Shift Register Mode Timing Waveforms
AC Testing Input/Output Waveforms(1)
Float Waveforms(1)
Note:
1.
AC Inputs during testing are driven at VCC - 0.5V for a logic 1 and 0.45V for a logic 0. Timing measurements are made at VIH min. for a logic 1 and VIL max. for a logic 0.
Note:
1.
For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to float when 100 mV change frothe loaded VOH/VOL level occurs.
12
AT89C4051
AT89C4051
TYPICAL ICC - ACTIVE (85°C)
20 Vcc=6.0V
I 15 C C 10 m A
5
Vcc=5.0V Vcc=3.0V
0 0 6 12 18 24
FREQUENCY (MHz)
AT89C4051
TYPICAL ICC - IDLE (85°C)
3 Vcc=6.0V
I C 2 C m 1 A
Vcc=5.0V
Vcc=3.0V 0 0 3 6 9 12
FREQUENCY (MHz)
AT89C4051
TYPICAL ICC vs. VOLTAGE- POWER DOWN (85°C)
20
I 15 C C 10 µ A
5
0 3.0V
4.0V
5.0V
6.0V
Vcc VOLTAGE
Notes:
1. 2. 3.
XTAL1 tied to GND for ICC (power down) P .1.0 and P1.1 = VCC or GND Lock bits programmed
13
Ordering Information
Speed (MHz) 12 Power Supply 3.0V to 6.0V Ordering Code AT89C4051-12PC AT89C4051-12SC AT89C4051-12PI AT89C4051-12SI AT89C4051-12PA AT89C4051-12SA 24 4.0V to 6.0V AT89C4051-24PC AT89C4051-24SC AT89C4051-24PI AT89C4051-24SI Package 20P3 20S 20P3 20S 20P3 20S 20P3 20S 20P3 20S Operation Range Commercial (0°C to 70°C) Industrial (-40°C to 85°C) Automotive (-40°C to 105°C) Commercial (0°C to 70°C) Industrial (-40°C to 85°C)
Package Type 20P3 20S 20 Lead, 0.300" Wide, Plastic Dual In-line Package (PDIP) 20 Lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC)
14
AT89C4051
AT89C4051
Packaging Information
20P3, 20-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-001 AD
1.060(26.9) .980(24.9)
.020(.508) .013(.330)
20S, 20-Lead, 0.300" Wide, Plastic Gull WIng Small Outline (SOIC) Dimensions in Inches and (Millimeters)
PIN 1
.280(7.11) .240(6.10) .090(2.29) MAX .005(.127) MIN
.299(7.60) .420(10.7) .291(7.39) .393(9.98) PIN 1 ID
.900(22.86) REF .210(5.33) MAX SEATING PLANE .150(3.81) .115(2.92) .110(2.79) .090(2.29) .070(1.78) .045(1.13) .325(8.26) .300(7.62) .014(.356) .008(.203) 0 REF 15
.050(1.27) BSC .513(13.0) .497(12.6)
.015(.381) MIN .022(.559) .014(.356)
.105(2.67) .092(2.34)
.012(.305) .003(.076)
.013(.330) .009(.229) 0 REF 8 .035(0.889) .015(.381)
.430(10.92) MAX
15