Text preview for : al1921_424.pdf part of Acer AL1921 Acer AL1921 Service Guide



Back to : al1921_424.pdf | Home

Acer AL1921 Service Guide

Service guide files and updates are available on the CSD web; for more information, please refer to http://csd.acer.com.tw

Copyright
Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation. Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders.

1

Conventions
The following conventions are used in this manual: Screen messages NOTE WARNING CAUTION IMPORTANT Denotes actual messages that appear on screen. Gives bits and pieces of additional information related to the current topic. Alerts you to any damage that might result from doing or not doing specific actions. Gives precautionary measures to avoid possible hardware or software problems. Reminds you to do specific actions relevant to the accomplishment of procedures.

2

Preface
Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. 2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

3

Warning: (For FCC Certified Models)
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.

Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. As an ENERGY STAR Partner our company has determined ENERGY STAR guidelines for energy efficiency. that this product meets the

Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

4

Precautions
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. 3.5A. The wall socket shall be installed near the equipment and shall be easily accessible.

5

Special Notes On LCD Monitors
The following symptoms are normal with LCD monitor and do not indicate a problem.

Notes
· Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off

the Power Switch and then turn it on again to make sure the flicker disappears. · You may find slightly uneven brightness on the screen depending on the desktop pattern you use. · The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time. · Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours.

6

Table Of Contents
Chapter 1 Monitor Features Monitor Features Electrical Requirements LCD Monitor General Specification LCD Panel Specification Support Timing Factory Preset Timing Table Block Diagram Main board Diagram Software Flowchart Main board Layout Mechanical Specification Front Bezel Rear Bezel Operating Instructions External Controls Front Panel Controls OSD Menu Hot-Key Menu OSD Message LOGO Update the firmware Machine Disassembly Troubleshooting Connector Information FRU (Field Replacement Unit) List Exploded Diagram Schematic Diagram Analog and Digital Input MST8131B LVD-S Key Board Connector Audio DC Power Online Support Information .................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... .................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... ................................................... .................................................... .................................................... .................................................... .................................................... ................................................... .................................................... ................................................... ................................................... ................................................... ................................................... ................................................... .................................................... 8 8 10 11 12 14 14 15 16 17 18 20 23 24 25 25 25 27 30 30 31 32 43 45 51 52 52 54 54 54 55 56 57 57 58

Chapter 2

Chapter 3 Chapter 4 Chapter 5 Chapter 6

Chapter 7

Appendix

7

Chapter 1
Monitor Features
AU EN02 Driving system Size Pixel pitch LCD Panel Brightness Contrast Viewable angle Response time Video Digital Input Separate H/V TTL Sync. H-Frequency 30KHz ­ 80KHz V-Frequency 55-75Hz 16.7M Colors 165MHz 1280 x 1024 @75Hz VESA DDC1/2BTM ON Mode OFF Mode 60W 5W D-Sub 15pin DVI-D 24pin Analog:0.7Vp-p(standard), 75 OHM, Positive Digital:DVI-D Horizontal : 376.32mm Vertical : 301.056mm 100~240VAC,47~63HZ Operating Temp: 5° to 50°C Storage Temp.: -20° to 65°C Operating Humidity: 10% to 85% 404.2(w)x330(H)x20(D) 4.2kg TFT Color LCD 48cm(19.0") 0.294mm( H )x 0.294mm( V ) 250cd/m2 (Typical) 700:1(Typical) 170° (H) 170° (V) 25ms(Tr+Tf ),Tr=15ms,Tf=10ms R,G,B Analog Interface Digital H/V TTL 30KHz ­ 80KHz 55-75Hz 16.7M Colors 165MHz 1280 x 1024 @75Hz VESA DDC1/2BTM 60W 5W D-Sub 15pin DVI-D 24pin Analog:0.7Vp-p(standard), 75 OHM, Positive Digital:DVI-D Horizontal : 376.32mm Vertical : 301.056mm 100~240VAC,47~63HZ Operating Temp: 5° to 50°C Storage Temp.: -20° to 65°C Operating Humidity: 10% to 85% 404.2(w)x330(H)x20(D) 4.2kg SEC E1-L01 TFT Color LCD 48cm(19.0") 0.294mm( H )x 0.294mm( V ) 250cd/m2 (Typical) 500:1(Typical) 170° (H) 170° (V) 25 ms(Tr+Tf)Tr=15ms/Tf=10ms

Display Colors Dot Clock Max. Resolution Plug & Play EPA STAR® ENERGY

Input Connector

Input Video Signal Display Size Power Source Environmental Considerations Dimensions Weight (N. W.)

8

· Auto Adjust Key

· Auto Adjust Key · · · · · · · · · · · · · · · · · · ·

Switch

External Controls:

Functions

· · · · · · · · · · · · · · · · · · ·

/ Volume Power Button MENU/ Exit Contrast Brightness Focus Clock H-Position V-Position Input Selected Language (Warm) Color (Cool)Color RGB Color temperature Reset OSD timeout information Exit

/ Volume Power Button MENU/ Exit Contrast Brightness Focus Clock H-Position V-Position Input Selected Language (Warm) Color (Cool)Color RGB Color temperature Reset OSD timeout information Exit

Power Consumption ( Maximum ) Audio Output Regulatory Compliance

60

60 Watts

Rated Power 2.5W rms (Per Rated Power 2.5W rms (Per channel) channel) CSA, TÜV/GS, CE, TCO'99, UL CSA, TÜV/GS, CE, TCO'99, UL

9

Electrical Requirements
Standard Test Conditions All tests shall be performed under the following conditions, unless otherwise specified. Ambient light : 225 lux Viewing distance : 40 cm in front of LCD panel Warm up time All specifications : 30 minutes Fully functional : 5 seconds Measuring equipment : Chroma 7120 signal generator or equivalent, directly Connected to the monitor under test. Control settings User brightness control : Maximum (unless otherwise specified ) User contrast control: Typical (unless otherwise specified ) User red/white balance, Green/white balance and Blue/white balance control : In the center (unless otherwise specified ) Power input: 90Vac or 240Vac Ambient temperature: 20 ± 5 °C Analog input mode: 1280 x1024 /75 Hz Measurement systems The units of measure stated in this document are listed below: 1 gamma = 1 nano tesla 1 tesla = 10,000 gauss cm = in x 2.54 lb = kg x 2.2 degrees F = [°C x 1.8] + 32 degrees C = [°F - 32]/1.8 u' = 4x/(-2x + 12y + 3) v' = 9y/(-2x + 12y + 3) x = (27u'/4)/[(9u'/2) - 12v' + 9] y = (3v')/[(9u'/2) - 12v' + 9] nits = cd/(m2) = Ft-L x 3.426 lux = foot-candle x 10.76

10

LCD Monitor General Specification
Panel type: 19 " active matrix color TFT LCD 1). AU EN02 Display size: 376.32mm (H) × 301.056mm(V) Display mode: VGA 640 × 480 (60//72/75 Hz) SVGA 800 × 600 (56/60/72/75 Hz) XGA 1024 × 768 (60/70/75 Hz) SXGA 1280 × 1024 (60//75 Hz) standard resolution Pixel pitch: 0.294mm(H) × 0.294mm(V) Display dot: 1280 x (RGB) × 1024 Pixel clock: 25.2 ­ 135.0MHz Contrast ratio: = 0° AU EN02 700:1 Brightness: AU EN02 250 cd/ Response time (Tr/Tf): AU EN02 (25ms) Display color: 16.7M(RGB 8 bit Data) Viewing angle: AU EN02 L / R 85/ 85 ( 160 degrees horizontal typical) U / D 75 / 75( 140 degrees vertical typical) Luminance uniformity: > 80 % (typical) Pc interface: 1).Video: RGB analog 0.7V peak to peak Sync: TTL positive or negative Signal connector: 15 pin Mini D type, (standard VGA video) 3.5 mm stereo audio jack (Audio) (For AR577 only) Audio power: 1.5Wrms + 0.5Wrms (300Hz ­ 1.3kHz) Front control: power on/off with LED select adjustment Interface frequency Horizontal Frequency 30KHz --80KHz Vertical Frequency 55Hz ------75Hz Plug & play: Support VESA DDC2B functions Power Input voltage: Single phase, 50/60HZ, 100 VAC to 240VAC ±10% Total output power: 60 Watt max.

11

LCD Panel Specification
LCD Panel Model (SEC E1-L01) Display Type active matrix color TFT LCD Resolution 1280x1024 pixels Display Dot 1280x (RGB) x 1024 Display Area 376.32mm(H) x 301.056mm(V) Pixel Pitch 0.294mm(H) x 0.294mm(V) Display Color 16.7M (true) Lamp Frequency 80kHz Lamp Current 7.0 mArms (typ) Weight 2750g (typ) Optical Specifications
IL = 6.5mArms Ta = 25 ± 2°C Symbol CR TR TF YL RX RY GX GY BX BY WX WY L R H L BUNI F LR CR10 70 70 70 70 =0, =0 Normal Viewing Angle VDD = 5V Condition FV = 60Hz MIN. 400 220 FDCLK = 54MHz TYP. 500 15 MAX. 20msec cd/mm UNIT

ITEM Contrast Ratio (Center of screen) Response Time at Ta Rising Falling

10
250 0.634 0.354 0.304

15
-

Luminance of white (Center of screen) Red Color Chromaticity (CIE) Green Blue White Hori. Vert.

TYP. -0.03

0.581 0.143 0.102 0.310 0.330 80 85 85 85 85 -

TYP. +0.03

80 25 1.7 % % Degrees

Viewing Angle

Brightness Uniformity Flicker Luminance Uniformity(TCO99)

12

Panel Relative Humidity

Input Signals Video input Type Input Impedance Polarity Positive Amplitude Display Color Sync input Signal

Analog R, G, B. 75 ohm +/- 2% 0 - 0.7 +/- 0.05 Vp same as LCD panel separate horizontal and vertical sync, or composite sync which are TTL compatible positive and negative.

Polarity Interface frequency The following frequency range is generalized by supported timing. If the entered mode does not match the supported timing the display optimization will not be assured. Horizontal Frequency 30KHz --83KHz Vertical Frequency 55Hz -----75Hz Panel bright dot defect and dark dot defect Test conditions: 1280*1024,64KHz/60Hz R.G.B.Full White and Full Black Pattern RECALL 1. 2. 3. 4. Bright Dots: R.G or B dots 3dots (G dots <3dots) Adjacent dot<1 groupTotal bright dots 3dots Dark Dots: -R.G or B dots 5dots - 2 adjacent dot<2 group Total dark dots 5dots Total(Dark & Bright) 7dots

13

Supported Timing
FH(KHZ)/ FV(HZ) 37.9/70 31.5/59.9 37.9/72.8 37.5/75 35.2/56.3 800x600 SVGA 1024x768 XGA 37.9/60.3 48.1/72.2 46.9/75 48.4/60.0 56.5/70.1 60/75 1280x1024 63.98/60.02 SYNC TOTAL ACTIVE POLARITY (DOT/LINE) (DOT/LINE) SYNC FRONT BACK PIXEL WIDTH PORCH PORCH FOREQ. (DOT/LINE) (DOT/LINE) (DOT/LINE) (MHZ) 64 96 40 64 72 128 120 80 136 136 96 112 144 32 8 16 16 24 40 56 16 24 24 16 48 16 96 40 120 120 128 88 64 160 160 144 176 248 248 25.175 25.175 31.5 31.5 36.0 40.0 50.0 49.0 60.0 70.0 75.0 108 135

TIMING 640x350 /DOS 640x480 VGA

+
-

800 800 800 840 1024 1056 1040 1056 1344 1328 1312 1688 1688

449 525 520 500 625 628 666 625 806 806 800 1066 1066

+ + +
+ -

SXGA

79.98/75.03

+ + +

Factory Preset Timing Table
STANDARD RESOLUTION 720 x 400 640 × 480 VGA 640 × 480 640 × 480 640 × 480 800 × 600 800 × 600 SVGA 800 × 600 800 × 600 832 x 624 1024 × 768 XGA 1024 × 768 1024 x 768 1024 × 768 HORIZONTAL FREQUENCY (kHz) 31.47 31.47 35.00 37.50 37.861 35.156 37.879 48.077 46.875 49.725 48.363 56.476 60.24 60.02
14

VERTICAL FREQUENCY (Hz) 70.0 60.0 66.6 75.0 72.8 56.3 60.0 72.2 75.0 75.0 60.0 70.0 74.9 75.0

Note: the IBM modes and Mac modes not in table, please refer to the spec!

Monitor Block Diagram
The LCD MONITOR will contain an main board, an inverter/power board, keypad board and internal adapter which house the flat panel control logic, brightness control logic and DDC. The Inverter board will drive the backlight of panel and the DC-DC conversion. The Adapter will provides the 12V DC-power to inverter/power board

Monitor Block Diagram

POWER(90V-264V) AUDIO IN

PWPC

LAMP

AUDIO

DC-DC

ANALOG IN

LCD Controller
-Scaler -OSD -LVDS IC -ADC

LCD PANEL

MCU

SPEAKER

KEY BOARD

SPEAKER

15

MAIN BOARD DIAGRAM
VCC3.3V AT24C02 (DDC)U301 DDC SCL/SDA VGA R/G/B VGA Input VGA Hsync/Vsync RXD/TXD AT24C02 (DDC)U302 U401 MST 8131B PA 0~9 PB 0~9 VCC2.5V VAA2 VAA4

VAA1

VAA3

HS/VS

Panel

U601 Winbond

DVI Signal VLCD

EPR SDA/SCL RGB AT24C16 U602 KEY Control

16

Software Flow Chart
1

1) 2) 3) 4)

2

Y N

3

4

5

N Y

6

7

N Y

8

MCU initialize. Is the eeprom blank? Program the eeprom by default values. Get the PWM value of brightness from eeprom. Check the pin PANEL1 and PANEL2 to tell which panel to get with it. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode. 9) Saving the power key status into eeprom. Turn on the LED and set it to green color. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light. 12) Check the analog and digital port, are there any signals coming? 13) Does the scalar send out a interrupt request? 14) Wake up the scalar. 15) Are there any signals coming from analog or digital port? 16) Display " No Input Signal " message. And go into standby mode after the message disappear. 17) Program the scalar to be able to show the coming mode. 18) Process the OSD display. 19) Read the keyboard. Is the power key pressed?

9

10

N

11

Y N
12 13

N

Y
14

Y
15

N

16

Y
17

18

N

19

Y
17

Monitor Board Layout

18

Label U201 U202 U301 U302 U401 U602 U603 U601 X401 X601 CN201 CN601 CN602 CN503 CN301 CN302

Component RT9164-25CL AIC1084-33CM M24C02-WMN6T SMT M24C02-WMN6T SMT MST8131B PQFP-12 AT24C16N-10SC-2.7 MAX810STR SOT-23 W78E65P-40 CRYSTAL 14.318MHzHC-49US 20MHZ WAFER 2*6P 2.0MM R/A PIN HEADER 2*7P 2.0mm WAFER 16PIN 2.0mm DIP PIN HEADER 24P 2.0mm 88L 35315F HS DVID CONN 24P

19

Mechanical Specification The step between front bezel and back cover shall be within specification. Top and Bottom Back cover & Bezel concavity 0.8mm A 1.3 mm Left and Right Back cover & Bezel concavity 0.8mm A 1.3 mm

Back Cover & Hinge Cover concavity 0mm B 0.5mm

Base & Neck concavity 0mm C 0.6mm

20

Top and Bottom Back cover & Bezel step 0mm D 0.8 mm

Left and Right Back cover & Bezel step 0mm D 0.8 mm

LCD Horizontally
The angle between front bezel and LCD unit in bottom side should not large than 1.0mm.

The distance of the LCD display unit from left side to right should not large than 4.0mm.

21

Tilt Base Rotation Tilt up 15 ± 2°/ down 5 ±2°

Plastic Material For TCO99 Front Bezel ABS 94HB Back Cover ABS 94HB The Others ABS 94HB For MPRII Front Bezel ABS 94HB Back Cover ABS 94HB The Others ABS 94HB GAP Spec. Gap between panel with bezel is 0 mm < gap < 1.2 mm

22

Front Bezel

Item 1 2 3 4 5

Description VEDIO UP VEDIO DOWM POWER MENU/ENTER AUTO/EXIT

23

Rear Bezel

Item 1 2 3 4

Description D-SUB Cable DVI CABLE AUDIO CABLE AC POWER CORD

24

Chapter 2
Operating Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. · The power cord should be connected. · Connect the video cable from the monitor to the video card. · Press the power button to turn on the monitor position. The power indicator will light up.

External Control Button

External Controls
1. >/ Volume 2.
Front Panel Control
· Power Button:

Press this button to turn the monitor ON or OFF.
· Menu / Enter :

Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status.
·
Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated.
· >/Volume:

Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated.

· Auto Adjust button / Exit:
25

1. When OSD menu is in active status, this button will act as EXIT-KEY(EXIT OSD menu). 2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.
· Power Indicator:

Green -- Orange NOTES

Power On mode. -- Off mode.

Notes
· Do not install the monitor in a location near heat sources such as radiators or air ducts, or

in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. · Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. · For maximum protection, repackage your monitor as it was originally packed at the factory. · To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.

1. 2. 3. 4. 5.

Press the MENU-button to activate the OSD window. See figure 4. Press to select the desired function. See figure 4. Press the MENU-button to select the function that you want to adjust. Press < or >to change the settings of the current function. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4.

26

Adjusting The Picture
1.) Main OSD Menu : a. Outline:

I. Analog-Only Model

II. Dual-Input Model, Analog Signal Input

III. Dual-Input Model, Digital Signal Input

27

b. The Description For Control Function :
Main Menu Icon Sub Menu Item Contrast Brightness Focus Clock H. Position V. Position Warm Cool User / Red User / Green User / Blue English Deutsch Français Español Italiano N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Sub Menu Icon Contrast from Digital-register. Backlight Adjustment Adjust Picture Phase to 0-100 0-100 reduce 0-100 Recall Cool Contrast Value Recall Cool Brightness Value Do Auto Config Do Auto Config Do Auto Config Do Auto Config The Color Temperature will be set to Cool. Color Temperature from N/A The User R/G/B value(default 0-100 0-100 0-100 N/A The Language will be set to English. is 100) will not be Modified by Reset function. Green Gain Digital-register. Blue Gain from Digital-register. Set OSD display language to English. Chinese. Set OSD display language to German. Set OSD display language to French. Set OSD display language to Spain. Set OSD display language to Italian. Chinese. H. Position V. Position OSD Timeout Set OSD display language to Japanese. Adjust the horizontal position of the OSD. Adjust the verticalposition of the OSD. Adjust the OSD timeout. N/A 0-100 0-100 10-120 50 50 10 N/A N/A N/A N/A Description Adjustmen t Range Reset Value

Horizontal-Line noise Adjust picture Clock to reduce Vertical-Line 0-100 noise. Adjust the horizontal position of the picture. Adjust the verticalposition of the picture. Recall Recall Warm Cool Color Temperature 0-100 0-100 from N/A

EEPROM. EEPROM. Red Gain from Digital-register.

Set OSD display language to Tranditional N/A

Set OSD display language to Simplified N/A

28

Auto Config

N/A

Auto Adjust the H/V Position, Focus and N/A Clock of picture.

N/A

(Analog-Only Model) Analog Digital (Dual-Input Model) Information N/A Show the resolution, H/V frequency and input N/A port of current iput timing. Reset N/A Clear each old status of Auto-configuration N/A and set the color temperature to Cool. Exit N/A Exit OSD N/A N/A N/A N/A N/A N/A Select input signal from analog (D-Sub) Select input signal from digital (DVI) N/A N/A N/A N/A

29

2.) Hot-Key Menu: a. Outline:

b. The Description For Hot-Key Function :
Item Operation Icon Description Volume of Audio adjustment. The Audio will be Mute when volume=0. Adjustment Range Volume When the OSD is closed, press Left or Right button will be Volume Hot-Key Function 0-100 Reset Value 50

3.) OSD Message: a. Outline:

b. The Description For OSD Message :
Item Auto Config Please Wait Input Not Supported Cable Not Connected No Signal the auto config function. 2.) When Digital signal input, without this OSD Message. When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor support range, will show this message. This message will be flying. 1.) Analog-Only Model : When the video cable is not connected, will show this message. This message will be flying. 2.) Dual-Input Model : Dual-Input Model without this OSD Message. 1.) Analog-Only Model : When the video cable is connected, but there is no active signal input, will show this message, then enter power saving. 2.) Dual-Input Model : When the video cable is not connected, or the video cable is connected but there is no active signal input, will show this message, then enter power saving. Description 1.) When Analog signal input, if User Press Hot-Key "Auto", will show this message, and the monitor do

30

4.) Logo: When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.

How To Optimize The DOS-Mode Plug And Play Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to operate properly, there must be a video input signal. This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse. Using The Right Power Cord The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration.
31

Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. Update the firmware 1.Tools: a. ISP Kit (Prepared by CMO) picture 1 b. RS232 Comport Cable -- picture 2 c. D-sub Cable d. Adapter

No.1 ­kit 2.Install kit as below: Step1--Get a Kit

No.2-kit

32

Step2---join RS232 Monitor cable,and Adapter

Connect to PC

Connect to monitor

Connect to adapter

Connect to chroma

Step3--When the LED turns Green, It will start running

33

3.Program Runnig Before update the firmware ,please power on the monitor, in this time,please push your finger to control the keyswitch(left: "< " right ", insert and draw the DC power ,the interface "> will appear "ISP" mode. Step1-Open the ISP tool. And Select the MCU type

34

Step2--Select Bank where is the new firmware ?

35

Step3--Choose the File Format a: when you already choose the New firmware ,a small pane appear "File Format",please choose the "inte he", no"Binary "and following choose the "OK"

36

Step4-- Select the communication Setting: Port Name,the "Port "the same your PC COM"

37

Step5-- Click the "ConNect" button.

38

Step6--

Before Executing ISP,the interface change as below Click "Program All" button that will execute erase and program

39

Step7--ISP is processing.

40

Step8-- Then you can get the window as follow, and Program ok.

41

Step9--Click "verify" button that will execute verify action. Then you can get the window as follow, and click ok.After update the program of APROM, must remove the Reboot Mode condition.

42

Chapter 3
Machine Disassembly
This chapter contains step-by-step procedures on how to assemble the monitor for maintenance. Disassembly Procedure Disassemble the base 1. Remove the neck cover. 2. Remove the four screws to release the hinge. 3. Remove the base

Disassemble the chassis
1. To fix the LVD cable with the panel,and stick 2. To fix the main frame on the panel 3. give the panel to lock the Screws 4.To fix the power board on the main frame with screws 1. To fix the audio board together with power board 6.To connect the main board with audio board and LVD cable 7.To fix the main board with screws. 8. To put the bezel on level place 9. To cover the panel with front bezel 10. To fix the shield on the main frame with screws 11. To put and fix the rear cover with screws 12. take the base together with interfaces 13. so the monitor was finishing!

1

2

3

4

5

6

7

8

9

10

43

11

12

13

NOTE:

1.The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. 2. Note: The monitor surface is susceptible to scratching!Therefore,lay the monitor on a soft surface when mounting or removing the base. 3.Wear gloves

Warning: 1.In order to prevent the static disturbance,wear resisting static ring 2. No watch

44

Chapter 4
Troubleshooting
This chapter provides troubleshooting information for the AL1921:

Main Board
1. No Screen Appear

Measured U201 pin 2 = 2.5 V? Measured U202 pin 2= 3.3V?

Check Correspondent component. Is there any shortage or cold solder? Check Power Board.

Yes, all DC level exist

Yes.there have OSD show Connected the Signal cable again, Check LED status.
Led Green

Disconnected the Signal cable( Loose the Signal cable ),Is the screen show "Cable Not
No, nothing is show Led Orange

Check Power switch is in Power-on

Replace U601 MCU
Led orange Check Correspondent

Connected the Signal cable again,
Led Green

status , and check if Power switch had been stuck ? OK, Keyboard no stuck

Check LED status.

Check the Wire-Harness from CN301

Measured RGB (R136,R138,R140) H,V Input at U601 pin 4,10 signal ? ,was there have

NG

component short/open ( Protection Diode ) and Signal cable bad ?

OK,Wire tight enough

Check Panel-Power Circuit
OK,Panel Power OK

OK,input Normal

Check U602 Data-output Block
OK, U203 data OK Replace Power board and Check Inverter control relative circuit

Measured Crystal X401(14.318MHz)

OK,clock normal

Replace U401 (MST8131B)

Re-do White balance adjust OK

Note:1.If Replace "MAIN-BOARD" ,Pleasere-do "DDC-content" programmed & "WHITE-Balance". 2. If Replace "Power Board" only, Please re-do " WHITE-Balance".
45

2.Panel-Power Circuit
Check the PPWR panel power relative circuit, Q301, Q302(pin 5,6,7,8) In normal operation, when LED =green, R302 should =0 v, If PPWR no-response when the power switch Turn on and turn off, replace the U203-MST8131B

Check R302 should have response from 0V to 5V When we switch the power switch from on to off

NG

OK,R308 have response NG, no Voltage Measured the Q302 pin 5,6,7,8= 5 V? Check U202 pin 1,2,3,4= 5V

Yes OK Replace Q302 ( Nmos, SI9933)

OK

3.Inverter Control Relative Circuit

Measured the inveter connector CN402 Pin2 on/off control=3.3V (on) Pin4 PWM signal control dim 0V-5V

NG

Check the Bklt-On relative circuit, R409, In normal operation, when LED =green, R409 Bklt-On should =5 v, If Bklt-On no-response when the power switch turn on-off, Replace U203 MST8131B

NG, still no screen NG

Replace Power board to new-one, and Check the screen is normal ??

Replace Power board & Re-do white balance

OK

46

4.U602-Data Output
NG , no transition Replace MST8131B (U401) or replace MAINBOARD.

Measured DCLK(R240)DVS, DHS (pin 117,116 from U203 ) Is the waveform ok? DCLK around 48 MHZ , DVS=60.09Hz , DHS around 80 KHz ?(refer to input signal=640x480@60 Hz 31k, and LED is Green) OK

Check U203 MST8131B, Signal output ER0~7,EG0~7,EB0~7,OR0~7,OG0~7,OB0~7, Is the waveform ok ?

If MainBoard being replace , please do the DDC ­ content

OK

heck U301,U302 LVDS IC Signal output

Replace U301,U302 LVDS IC or replace MAINBOARD.

OK

47

Power/Inverter Board
1.) No Power

Check to CN102 Pin1 and pin2 = 5V NG OK

Check Interface board

Check AC line volt 120V or 220V NG OK Change F901 , check BD901,Q903,IC901

Check the voltage of C905(+) NG OK Check bridge rectified circuit cFailure

Check start voltage for the pin3 of IC901 NG OK Repeating the start voltage Change IC901

Check the auxiliary voltage is smaller than 20V NG 1) Check IC902, IC903 2) Check Q901,Q902...OVP circuit Check R919, D910,D911,D912,D913, ZD904

OK

48

2.) W / LED , No Backlight

Check C201(+) =12V OK NG Change F902 Check D201/Q209/Q210 or D202/Q211/Q212 Check ON/OFF signal NG OK Check Interface board

Check U201 pin9=12V pin9=12vvoltage of C905(+) OK NG Change Q201 or Q202

Check the pin1 of U201 have sawtooth wave OK NG Change U201

Check D201(-),D202(-) have the output of square wave at short time. OK NG Check Q205/Q207/Q203/D201 or Q206/Q208/Q204/D202 Check the resonant wave of pin2 & pin5 for PT201/PT202 NG

OK

Check Q209/Q210/C213 or Q211/Q212/C214

Check the output of PT201/PT202 OK NG Change PT201or PT202

Check connecter & lamp
49

KeyPad Board

OSD is unstable or not working

Is KeyPad Board

N Connect KeyPad Board

ti

ll ? Y N

Is Button Switch normally ?

Replace Button Switch

Y N Is KeyPad Board Normally ? Y Check Main Board Replace KeyPad Board

50

Chapter 5
Connector Information
The following figure shows the connector locations on the monitor board:

1 6 11

5 10 15

15 - Pin Color Display Signal Cable(D-sub)

PIN NO. 1. 2. 3. 4. 5. 6. 7. 8.

DESCRIPTION Red Green Blue Ground Ground R-Ground G-Ground B-Ground

PI N NO. 9. 10. 11. 12. 13. 14. 15.

DESCRIPTION NC Ground Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock

24 - Pin Color Display Signal Cable(DVI)

Pin 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.

Meaning TMDS Data2TMDS Data2+ TMDS Data 2/4 Shield not connected not connected DDC Clock DDC Data Analogue Vertical Sync TMDS Data1TMDS Data1+ TMDS Data 1/3 Shield not connected

Pin 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.

Meaning not connected +5V Power Ground Hot Plug Detect TMDS Data0TMDS Data0+ TMDS Data 0/5 Shield not connected not connected DDC Clock Shield DDC Clock+ DDC Clock-

51

Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU ( Field Replaceable Unit ) listing in global configurations of Acer Altos AL1921 .Refer to this chapter whenever ordering for parts to repair or for RMA ( Return Merchandise Authorization ).Please note that WHENORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines. Note: To scrap or to return the defective parts, you should follow the local goverment ordinance or regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it. Exploded Diagram

52

Note: Above picture show the description of the following component Item 1 Picture Description HOLDER CABLE Part No. W33L4633-GD-X

2

ARM 20L003-1

3

SCREW

M1L 330 6120

4

SCREW

Q1L 130 6120

5 6

FOOT-PORON BASE

12L 394 3 34L1337-GD-B

7

BASE PLATE

15L8022 -1

8

HINGE

37L-498 -1

9

SHIELD

85L-666-1

10

MAIN FRAME

15L8021-1

11 Key pad 12 REAR COVER

33L4634-AI -L

34L1336-AGD-2B

53

Chapter 7
Schematic Diagram
Analog And Digital Input
11 12 13 14 15 CN301 DB15 1 6 2 7 3 8 4 9 5 10 RXD TXD 6 6 FB301 FB302 FB303 PC5V VGA_CON 75 0 0 0 1/16W 1/16W 1/16W R326 1/16W R327 1/16W R325 1/16W C301 NC C302 NC C303 NC R305 R306 R307 3 3 D301 BAV99 D302 BAV99 3 D303 BAV99 VCC5V VCC5V R308 10K 1/16W 100 1K 1K 1/16W 1/16W 1/16W VCC5V 2 PC5V 1 D304 BAT54C-GS08 D319 MLL5232B 5.6V D320 MLL5232B 5.6V R313 2.2K 1/16W C311 33pF R314 2.2K 1/16W C312 220pF D317 MLL5232B 5.6V 20K R315 R316 100 100 3 R317 1/16W R318 20K 1/16W 8 7 6 5 68 68 68 1/16W 1/16W 1/16W C308 0.047uF C309 0.047uF C310 0.047uF GNDR GNDG GNDB 4 4 4 R301 R302 R303 R304 33 33 33 470 1/16W 1/16W 1/16W C304 0.047uF C305 0.047uF C306 0.047uF RIN GIN BIN SOG 4 4 4 4

1/16W C307 0.001uF

75

2

1

2

1

2

1

75

R309 HSI VSI FB304 R312 100 150 OHM 1/16W R310 R311

ST_DET1 6 HSYNC VSYNC 4 4

U301 VCC WP SCL SDA A0 A1 A2 GND 1 2 3 4

C313 0.1uF

CLK_DDC DAT_DDC CN302 R G B RGB GND HSYNC VSYNC SYNC GND DDC SCL DDC SDA +5V HPD 1/3shield 2/4shield 0/5shield clk shield DAT0+ DAT0DAT1+ DAT1DAT2+ DAT2DAT3+ DAT3DAT4+ DAT4DAT5+ DAT5clk+ clkJACK 25 26 27 29 28 8 15 6 7 14 16 11 3 19 22 18 17 10 9 2 1 13 12 5 4 21 20 23 24 3 3 3 3 3 3 3 D306 BAV99 NC D307 BAV99 NC D308 BAV99 NC D309 BAV99 NC D310 BAV99 NC D311 BAV99 NC D312 BAV99 NC 3 D313 BAV99 NC VCC5V 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 D321 MLL5232B 5.6V D318 MLL5232B 5.6V 6 6

1/16W 1/16W

AT24C02N-10SC DDC_DAT DDC_CLK VCC5V 2 DVI5V 1 D305 BAT54C-GS08 R322 100 1/16W ST_DET2 6 R323 20K B+ BG+ GR+ R4 4 4 4 4 4 1/16W 20K R324 1/16W 8 7 6 5 3

CLK_DDC2 DAT_DDC2

R319 R320

100 100

1/16W 1/16W

DVI5V

R321 10K 1/16W

D314 MLL5232B 5.6V

D315 MLL5232B 5.6V

D316 MLL5232B 5.6V

C314 0.1uF

U302 VCC WP SCL SDA A0 A1 A2 GND 1 2 3 4

C315 0.1uF

AT24C02N-10SC

CLK+ CLK-

4 4

Title

MST8XXXB for AOC
Size B Date: Document Number Rev

INPUT
, 03, 2003 Sheet 3 of 7

A

MST8131B
VCPU 2 VCPU R602 C601 0.1uF 1/16W U601 35 EA/VP XTAL1 XTAL2 RESET P4.3 INT0/P3.2 INT1/P3.3 ALE/P PSEN P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 W78E65P-40 21 20 10 R603 D601 LL4148 VCPU C605 0.1uF 1 2 3 4 R604 R605 R615 VCC WP SCL SDA 8 7 6 5 R642 NC VCPU 1 2 3 4 7 AUDIO_SD R626 10K 1/16W 3 3 ST_DET1 ST_DET2 NC CN603 R612 C613 R613 10K 1/16W 0.1uF NC R641 10K 10K 10K 0 1/16W 1/16W 1/16W R608 R609 100 100 1/16W 1/16W 4 10K 1/16W 33 32 2 3 4 5 6 7 8 9 INT 12 14 15 44 10K RP601 1/16W 10K 1/16W POWER MENU RIGHT LEFT AUTO LED_B LED_O LED_G 4 3 2 1 4 3 2 1 R637 RP602 10K 1/16W 10K 5 6 7 8 5 6 7 8 10K 1/16W 1/16W R638 R639

R601 10K C602 22pF

1/16W 10K

921110:
VCPU U603 3 VCC MAX810STR (NC) RST 2 R643 NC C603 10uF/16V +

Y601 20MHz C604 22pF

GND

P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 T0/P3.4 T1/P3.5 P3.6/WR P3.7/RD P3.1/TXD P3.0/RXD

43 42 41 40 39 38 37 36 24 25 26 27 28 29 30 31 16 17 18 19 13 11

VCC

R636 100 1/16W

Reset Circuit
U602 A0 A1 A2 GND 24C16

R606 R607

10K 10K

1/16W 1/16W

HWRESET 4 onPANEL_5V/3.3V onBACKLITE 2 CSZ 4 SCL 4 SDA 4

2

1

VCPU AD0 AD1 AD2 AD3 DDC_DAT DDC_CLK TXD RXD 4 4 4 4 3 3 3 3

1/16W

C612 0.1uF

2 onAUDIO 2 onPANEL_12V

22

R610 R611 R634 R635

NC NC 100 100

VSS

1/16W 1/16W

CN604 VCPU VCPU LED_GRN K_RIGHT K_AUTO K_POWER LED_BLUE EAR_R OUT_R 1 3 5 7 9 11 13 CONN Q601 PMBS3906 0 0 0 1/16W 1/16W 1/16W C608 C606 C607 LED_GRN K_RIGHT K_AUTO K_POWER LED_ORANGE EAR_R OUT_R 1 3 5 7 2 11 13 3 CN602 9 4 6 8 10 12 14 CONN(NC) Title LED_BLUE K_LEFT K_MENU EAR_L OUT_L C610 C609 R640 R623 R624 C614 1uF 470 1/16W 0 1/16W 0 1/16W LEFT MENU 2 4 6 8 10 12 14 LED_ORANGE K_LEFT K_MENU

VCPU

R628 EAR_L OUT_L 2 0 1/16W 4.7K 1/16W R629

R618 120 4.7K 1/16W R619 LED_O 1 2 1/16W 4.7K 1/16W R616 Q602 PMBS3906 3 LED_G 1 2

R617 120 1/16W

1 Q603 PMBS3906 3

LED_B

RIGHT R622 AUTO R620 POWER R621

0.001uF 0.001uF

0.001uF 0.001uF 0.001uF

MST8XXXB for AOC
7 7 EAR_R OUT_R EAR_L OUT_L 7 7 Size B Date: Document Number

MPU
Sheet 6 of 7

Rev

A

, 03, 2003

54

VAD

VPLL VDVI

VDPLL

VPO

VDD

C406 C407 C408 C409 C410 C411 C412 C413 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF

C415 C416 C417 C418 0.1uF 0.1uF 0.1uF 0.1uF

11 21 84 94 104 114 126 VDDP VDDP VDDP VDDP VDDP VDDP VDDP

AVDD_MPLL

AVDD_PLL

AVDD_DVI AVDD_DVI

AVDD AVDD

VDDC VDDC VDDC VDDC

U401 MST8116B 63 62 60 59 61 58 57 37 38 29 28

18 87 97 117

55 65

35

45 51

53

3 3 3 3 3 3 3 3 3

RIN GNDR GIN GNDG SOG BIN GNDB HSYNC VSYNC

RIN0 RIN0M GIN0 GIN0M SOGIN0 BIN0 BIN0M HSYNC0 VSYNC0 DDC1_CLK/GPO8 DDC1_DAT/GPO7

LVA3p/GA3P LVA3M/GA3N LVACKP/NC LVACKM/NC LVA2P/RA1P LVA2M/RA1N LVA1P/RA2P LVA1MRA2N LVA0P/RA3P LVA0M/RA3N GA1P GA1N GA2P GA2N BA1P BA1N BA2P BA2N BA3P BA3N NC/RB1P NC/RB1N NC/RB2P NC/RB2N NC/RB3P NC/RB3N NC/GB1P NC/GB1N NC/GB2P NC/GB2N NC/GB3P NC/GB3N LVB3P/CLKAP LVB3M/CLKAN LVBCKMP/NC/CLKBP LVBCKP/NC/CLKBN LVB2P/NC LVB2M/NC LVB1P/NC/BB1P LVB1M/NC/BB1N LVB0P/NC/BB2P LVB0M/NC/BB2N NC/BB3P NC/BB3N NC/ESP OSP

102 103 106 107 108 109 110 111 112 113 98 99 100 101 88 89 90 91 92 93 16 17 22 23 24 25 8 9 12 13 14 15 118 119 120 121 122 123 124 125 128 1 4 5 75 76

PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8 PA9 GA0 GA1 GA2 GA3 BA0 BA1 BA2 BA3 BA4 BA5 RB0 RB1 RB2 RB3 RB4 RB5 GB0 GB1 GB2 GB3 GB4 GB5 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 BB0 BB1

VAA1 FB403 PA[0..9] GA[0..3] PA[0..9] GA[0..3] 5 5 2 VAA1 600 OHM C419 10uF/16V BA[0..5] BA[0..5] 5

VAD

3 3 3 3 3 3 3 3 VDVI VCC3.3 R401 Direct Bus 3-WIRE NC 4.7K VCC5V R402 4.7K NC R402 4.7K

R+ RG+ GB+ BCLK+ CLKR403 390 1/16W

40 41 43 44 46 47 49 50 52

+ C420 C421 0.1uF 0.1uF

R+ RG+ GB+ BCK+ CKREXT

RB[0..5]

RB[0..5]

5 VAA2 2 VAA2 FB404 600 OHM C422 10uF/16V + C423 0.1uF VPLL

C401 1/16W 0.1uF

66 67

REFP REFM

GB[0..5]

GB[0..5]

5

6 R407 R405 R404 R406 10K R401 6 CSZ 10K 10K 10K 1/16W 1/16W 1/16W 1/16W SCL NC 6 6 SDA 6 HWRESET 6 INT 69 71 70 32 72 30 77 78 31 VCC5V 2 AdjBACKLITE R410 4.7K R408 1K 1/16W 3 1/16W 33 73 74

BUS TYPE CSZ SCL SDA HWRESETZ INT AD0 AD1 AD2 AD3 PWM0 PWM1 XIN

PB[0..9]

PB[0..9]

5 2 VAA3

VAA3

FB405 600 OHM C424 10uF/16V

VDVI

6 6 6 6

AD0 AD1 AD2 AD3

+ C425 C426 0.1uF 0.1uF

BB[0..1] ESP OSP

BB[0..1] ESP OSP

5 5 5 VAA4 FB406 600 OHM C427 10uF/16V + VDPLL

C402 22pF X401 1 PMBS3904 Q401 14.318MHz C403 22pF C404 0.1uF

34 3 2

XOUT BYPASS AVSS_LPLL

AVSS_PLL

AVSS_DVI AVSS_DVI AVSS_DVI

7

VOLUME

R409 10K 1/16W

AVSS_MPLL

GPO0 GPO1 GPO2 GPO3 GPO4 19 86 GNDC 96 GNDC 116 GNDC GNDC GNDP GNDP GNDP GNDP GNDP GNDP GNDP

83 82 81 80 79

GPO0 GPO1 GPO2 GPO3 GPO4

GPO[0..4]

GPO[0..4] 5

2

VAA4

2

10 20 85 95 105 115 127

68 56 64

36

54

39 42 48

C430 100pF

C429 1uF

AVSS AVSS AVSS

C428 0.1uF

Title Size B Date:

MST8XXXB for AOC
Document Number

SCALER
Sheet 4 of 7

Rev

A

, 03, 2003

LVD-S
4 PA[0..9] PA[0..9] 4 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB[0..9] PA8 PA9 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 LVA3P LVA3M LVACKP LVACKM LVA2P LVA2M LVA1P LVA1M LVA0P LVA0M LVB3P LVB3M LVBCKP LVBCKM LVB2P LVB2M LVB1P LVB1M LVB0P LVB0M 4 GA[0..3] GA[0..3] GA0 GA1 GA2 GA3 PA0 PA1 GA1P GA1N GA2P GA2N GA3P GA3N 4 BA[0..5] BA0 BA1 BA2 BA3 BA4 BA5 PB0 PB1 BA1P BA1N BA2P BA2N BA3P BA3N CLKAP CLKAN PB[0..9] PA[0..9] PA[0..9] PA4 PA5 PA6 PA7 PA8 PA9 RA1P RA1N RA2P RA2N RA3P RA3N 4 GB[0..5] 4 RB[0..5] RB[0..5] RB0 RB1 RB2 RB3 RB4 RB5 GB[0..5] GB0 GB1 GB2 GB3 GB4 GB5 PB[0..9] PB2 PB3 PB6 PB7 PB8 PB9 BB0 BB1 CLKBP CLKBN BB1P BB1N BB2P BB2N BB3P BB3N GB1P GB1N GB2P GB2N GB3P GB3N RB1P RB1N RB2P RB2N RB3P RB3N RA3N RA3P RA2N RA2P RA1N RA1P GA3N GA3P GA2N GA2P GA1N GA1P CLKAN CLKAP BA3N BA3P BA2N BA2P BA1N BA1P 4 GPO0 GPO1 GPO2 GPO3 GPO4 R501 R502 R503 R504 R505 0 0 0 0 0 1/16W 1/16W 1/16W 1/16W 1/16W GPOO0 GPOO1 GPOO2 GPOO3 GPOO4 4 OSP ESP OSP ESP R506 R507 R39 15"RSDS 17"RSDS 2 C501 C502 C503 C504 C505 NC NC NC NC NC 2 VLCD VLCD VLCD_12V VLCD_12V + C508 C512 22uF/16V 0.1uF 0R 0R 0 0 1/16W 1/16W R41 NC 0R C506 NC C507 NC GPOO1 GPOO0 GPOO3 GPOO2 GPOO4 0 FB0N FB0P FB1N FB1P FB2N FB2P FG0N FG0P FG1N FG1P FG2N FG2P FCLKN FCLKP FR0N FR0P FR1N FR1P FR2N FR2P STH LP POL HMS CLKV STV OE 1/16W 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN501 RB3N B0N RB3P B0P RB2N B1N RB2P B1P RB1N B2N RB1P B2P GB3N BG0N GB3P BG0P GB2N BG1N GB2P BG1P GB1N BG2N GB1P BG2P CLKBNBCLKN CLKBPBCLKP BB3N BR0N BB3P BR0P BB2N BR1N BB2P BR1P BB1N BR2N BB1P BR2P 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN502

4

PB[0..9]

4

PA[0..9]

PA[0..9]

4

BA[0..5]

4

BB[0..1]

BB[0..1]

4

PB[0..9]

PB[0..9]

4

GPO[0..4]

GPO[0..4]

CONN

R508 R509 R510 R511 R512 R513 R514

NC 0 1/16W NC 0 1/16W NC NC

CN503 LVB0M RXO0LVB1M RXO1LVB2M RXO2LVBCKM RXOCLVB3M RXO3LVA0M RXE0LVA1M RXE1LVA2M RXE2LVACKM RXECLVA3M RXE31 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 RXO0+ RXO1+ RXO2+ RXOC+ RXO3+ RXE0+ RXE1+ RXE2+ RXEC+ RXE3+ LVB0P LVB1P LVB2P LVBCKP LVB3P LVA0P LVA1P LVA2P LVACKP LVA3P

CONN

R508 AU 17 QDI 17 CPT 17 INNOLUX 15 HannStar 15 CPT 15 LG 15 NC 3.3V 0R 3.3V 0R 3.3V 0R 3.3V 0R

R509 NC 12V 0R NC NC NC

R510 5V 0R NC 3.3V 0R 3.3V 0R 3.3V 0R

R511 5V 0R NC NC NC NC

R512 NC 12V 0R NC 12V 0R NC

R513 5V 0R NC NC NC NC

R514 NC 12V 0R NC NC NC C509 + 22uF/16V

CONN VLCD VLCD 2

C510 0.1uF

C511 0.1uF

Title

MST8XXXB for AOC
Size B Date: Document Number Rev Sheet 5 of 7

PANEL INTERFACE
, 03, 2003

A

55

Key Board Connector
NEW ADD CIRCUIT FOR 4 LED 04/09 +5V R407 NC R408 NC +3.3V 0 1/16W +3.3V

R406 FB405 600 OHM C406 NC LED_GRN LED_ORG KEY_AUTO KEY ENTER KEY_RIGHT KEY LEFT KEYON_OFF GND GND 60

LED_BLUE# R403 NEW ADD CIRCUIT FOR 4 LED 10K 1/16W 04/09 1 2 3 4 8 7 6 5 RP402 10K 1/16W +5V +3.3V

CN403 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CONN

C405 NC GND

JP403,JP404 Package JP403 JP404



JP403
4.7K 1/16W 4 3 2 1

JP404

FB403

FB404

600 OHM 600 OHM FB401

60

FB402 C408 150pF C423 68pF C407 150pF

Earphone(R) P.6 Earphone(L) P.6 OUT(L) P.6 OUT(R) OUT(R) P.6

P.4 P.4 P.4 P.4 P.4

GPIO7 GPIO6 GPIO3 GPIO2 GPIO8

RP401 5 6 7 8

R404 R405 1K 1/16W NC KEY_RIGHT KEY ENTER KEY_AUTO KEYON_OFF KEY LEFT R218 1K VOL_OUT

VOL

0603

0603

VOL_OUT

R412 4.7K +5V

+

C250 22uF/16V

8

7

6

5

C422 68pF

C430 NC 1 2 3 4

CP301 NC

R422 1K 1/16W

R423 1K 1/16W STDBY R421 0 MUTE R420 0 C420 C421

GND

VOL

VOL

3

STBY_OUT

STDBY

3

GND GND EMI SOULATION ADD C422,C423,FB403,FB404 2003/02/21

MUTE_OUT GND

MUTE

3

R431 NC

+5V

R429 NC

R427

+3.3V R428 NC C415 NC LED_BLUE#

0.1uF/16V 0.1uF/16V GND GND U106F 74HCT14 12 0 1/16W 7

NC R426 4LED NC 1 2 3 Q403 NC

14

2003/02/21 EMI SOULATION NEW C421 & C420 104 13

R401 LED_GRN C417 NC GND

P.4

LED_GREEN

C414 NC GND NEW ADD CIRCUIT FOR 4 LED 04/09 GND

CN402 2 4 6 8 10 12 CONN 1 3 5 7 9 11 4.7K 1/16W

R409

PBIAS BackLight On/Off Brightness P.4 +12V GND +5V

1/10

NEW ADD CIRCUIT FOR 4 LED 04/08 +3.3V +3.3V +5V 14 U106A 74HCT14 2 R402 LED_ORG 0 1/16W 7 C419 NC GND

+12V

+5V

+5V
R413 470 1/16W +5V GND C410 0.1uF/16V D401 MLL4148 R414 1 LED_GRN 330 1/16W R424 NC Title Size B NEW ADD CIRCUIT FOR 4 LED 04/09 Date: R416 0 1/16W D402 NC 2 2 C409 + 150uF/25V + C411 150uF/25V C412 0.1uF/16V R415 1 1K 1/16W LED_ORG R430 NC R418 NC R417 R419 220 1/16W NC P.4 LED_ORANGE

1

1/10
Q402 PMBS3906 3

R410 620 1/16W

NEW ADD CIRCUIT FOR 4 LED 04/08

Brightness
P.4 PWM0

PWM0 R411 1K 1/16W GND LED_GRN

Q401 PMBS3906 3

R425 + C413 22uF/16V LED_BLUE# GND NC

ACER GM5120/2120
K.B AND CONNECTOR
Document Number

715L1123-A
Sheet 5 of 5

Rev

A

Monday, May 12, 2003

56

Audio
VCC12V_AUDIO

2

VCC12V_AUDIO + C701 470uF/16V + C702 470uF/16V C703 0.1uF

R702 NC


16 VS VS 1 5 4 3 2 R701 R703 D701 10K PHONEJACK 1/16W D702 LL4148 R706 LL4148 100 1/16W C709 1uF C712 100pF R712 VOL 220K C713 0.1uF 1/16W 5.6K 5.6K C710 1uF R704 R705 10K 1/16W 100 1/16W 6 11 12 10K 1/16W C704 C706 0.47uF/16V 0.47uF/16V 4 9 NC CN701 6 AUDIO_SD MUTE 15 8 INL INR VOLUME STBY MUTE OUTL OUTR SVR VAROUT_R VAROUT_L

U701 TDA7496L EAR_L 17 14 10 7 5 + C708 R707 1K 1/16W R708 1K 1/16W R709 NC C705 470uF/16V C707 470uF/16V + + OUT_L OUT_R EAR_R 6 6 6 6

GND GND GND GND GND GND GND

C711 100pF

1 2 3 13 18 19 20

470uF/16V

R710 1/16W

R711 1/16W

VOLUME

4

DC Power
VCC5V VCC12V R202 CN201 GND GND VCC12V GND VCC5V GND 1 3 5 7 9 11 2 4 6 8 10 12 ON_OFF DIM VCC12V GND VCC5V GND R201 D201 4.7K 1/16W C209 3 SS14 VCC5V+ VCC5V C201 0.1uF 2 R212 4.7K 1 Q201 PMBS3904 1/16W onBACKLITE 6 47uF/16V + C210 0.1uF 1 10K 1/16W VCC5V+

D202 GS1D 3

SOT-223
U201 RT9164-25CG VI GND VO 2 C211 47uF/16V + C212 0.1uF VCC2.5 VCC2.5 4

CONN

FB201 600 OHM

VCPU VCPU 6

VCC5V C202 + R203 1K 1/16W 220uF/25V 0.1uF C203 + 220uF/25V C204 C205 0.1uF

Brightness
R205 4.7K 4 AdjBACKLITE 1/16W 1 R204 10K 1/16W Q202 PMBS3904 2 C206 1uF 3 VCC5V+

VCC3.3

VCC3.3

4

SOT-263
U202 VIN ADJ AIC1084-33M 3 C213 + C214 0.1uF 1 VOUT 2 C215 47uF/16V + C216 0.1uF

VAA1 VAA1 VAA2 VAA2 VAA3 VAA3 4 4 4

VCC5V

VLCD VLCD 5 VCC5V VCC3.3

47uF/16V

R206 10K 1/16W

R208 10K 1/16W Q203 AO3401 R209 NC R210 0 1/16W VAA4

VAA4

4

R207 4.7K 6 onPanel_5V/3.3V

1/16W 1 C207 0.1uF

3 Q204 PMBS3904 + C208 10uF/16V R211 10K 1/16W 2 VCC12V

VCC5V

VLCD_12V VLCD_12V 5

VCC5V

VCC12V

VCC12V_AUDIO VCC12V_AUDIO 7

R213 10K 1/16W

R215 10K 1/16W Q206 AO3407 3

R217 10K 1/16W

R219 10K 1/16W Q208 AO3407

R214 4.7K 6 onPanel_12V

1/16W 1 C217 0.1uF

R218 4.7K Q205 PMBS3904 + C218 10uF/16V R216 4.7K 1/16W VCC12V 6 onAUDIO

1/16W 1 C219 0.1uF

3 Q207 PMBS3904 + C220 10uF/16V R220 4.7K 1/16W Size B Date: 2

VCC12V Title

2

MST8XXXB for AOC
Document Number

POWER
Sheet 2 of 7

Rev

A

, 03, 2003

57

Appendix
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan. Acer's Website offers you convenient and valuable support resources whenever you need them.In the Technical Information section you can download information on all of Acer's Notebook, Desktop. Server models including: Service guides User's manuals Training materials Bios updates Spare parts lists TABs (Technical Announcement Bulletin) For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of technical material. Also contained on this website are: Detailed information on Acer's International Traveler's Warranty (ITW) Returned material authorization procedures An overview of all the support services we offer, accompanied by a list of telephone, fax contacts for all your technical queries. We are always looking for ways to optimize and improve our services, so if you have any suggestions comments, please do not hesitate to communicate these to us.

58