Text preview for : x233h_963.pdf part of Acer X233H LCD Monitor
Back to : x233h_963.pdf | Home
t
ne
el.
wj
w.
ww
://
tp
Acer X233H
ht
Service Guide
1
Service Guide Version and Revision
Version Release Date Revision History Customer model TPV model
A00 Dec.-02-2008 Initial Release X233H TDRSNDD8Y2ABPN
t
ne
el.
wj
w.
ww
://
tp
ht
2
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties
of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is
sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer
Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software.
t
ne
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
el.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
wj
Trademarks
Acer is a registered trademark of Acer Incorporated.
w.
All other trademarks are property of their respective owners.
ww
Conventions
The following conventions are used in this manual:
Screen messages Denotes actual messages that appear on screen.
://
Note Gives bits and pieces of additional information related to the current topic.
Warning Alerts you to any damage that might result from doing or not doing specific actions.
tp
Caution Gives precautionary measures to avoid possible hardware or software problems.
Important Remind you to do specific actions relevant to the accomplishment of procedures.
ht
3
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided
for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness,
your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra
memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such
cases, please contact your regional offices or the responsible personnel/channel to provide you with further
technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on
your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the
printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
t
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list
ne
provided by your regional Acer office to order FRU parts for repair and service of customer machines.
Warning: (For FCC Certified Models)
el.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
wj
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed
w.
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
ww
is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
://
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
tp
Notice:
ht
1. The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this
equipment. It is the responsibility of the user to correct such interference.
As ENERGY STAR® Partner our company has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present
inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
4
Precautions
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in
a wet basement.
Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold
with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer
and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.
Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator
or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
t
ne
the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
el.
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
wj
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
w.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
ww
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
://
configured receptacles marked between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
tp
Special Notes On LCD Monitors
ht
The following symptoms are normal with LCD monitor and do not indicate a problem.
Notes
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and
then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,
when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image
or turning off the Power Switch for hours.
5
Table Of Contents
Chapter 1 Monitor Features ................................................ 7
Introduction ............................................. 7
Electrical Requirements ............................................. 8
LCD Monitor General Specification ............................................. 9
LCD Panel Specification ............................................. 10
Factory Preset Timing ............................................. 13
Monitor Block Diagram ............................................. 14
Main Board Diagram ............................................. 15
Software Flow chart ............................................. 16
Main Board Layout ............................................. 18
Installation ............................................. 19
t
ne
Chapter 2 Operating Instructions ............................................. 21
External Controls ............................................. 21
el.
Front Panel Controls ............................................. 21
eColor Management (OSD) ............................................. 22
wj
How to Adjust a Setting ............................................. 23
How To Optimize The DOS-Mode ............................................. 26
Enter into the factory mode ............................................. 26
w.
Chapter 3 Machine Disassembly ............................................. 27
ww
Chapter 4 Troubleshooting ............................................. 30
Chapter 5 Connector Information ............................................. 36
://
Chapter 6 FRU (Field Replacement Unit) List ............................................. 37
tp
Exploded Diagram ............................................. 37
ht
Chapter 7 Schematic Diagram ............................................. 42
6
Monitor Features Chapter 1
Introduction
Scope
This short specification describes the electrical, optical and functional performance requirements for a 58.4cm (23")
TFT LCD color monitor with VGA&DVI compatible interface.
Description
The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no
radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop
space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF
target is 50k hours or more.
t
ne
Chart of X233H
el.
Panel LTM230HT01 A03(003) SZ SEC
Signal Interface D-Sub 15pin;DVI 24pin
wj
Sync Type Separate / Compatible
Color Temp User Adjust Support
w.
DDC DDC2B
Speaker Yes
ww
Headphone Jack No
Microphone Jack No
://
USB Hub support
Tilt / Swivel Yes /No
tp
ht
7
Electrical Requirements of X233H
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified.
Ambient light Dark room (< 1 cd/m2)
Viewing distance 40 cm for LCD performance, 20 cm for LCD failures
Warm up time 30 minutes
Analog Input signal 700 mVss
Control temperature 6500° K
User brightness control The value under user mode
Set to factory preset value, which allows that the brightest two of
User contrast control 32 linear distributed gray-scales (0 700mv) can be
distinguished.
Picture position and size Factory preset value
Viewing angle 90° H and V
AC Supply voltage 230V± 5, 50±3Hz
t
Ambient temperature 20+5
ne
Humidity 65% ± 20%
Display mode 1920 x 1080, 60 Hz, all white
e-color mode Set to "User" mode
el.
wj
Measurement systems
The units of measure stated in this document are listed below:
w.
1 gamma = 1 nano tesla
1 tesla = 10,000 gauss
ww
cm = in x 2.54
Lb = kg x 2.2
Degrees F = [°C x 1.8] + 32
Degrees C = [°F - 32]/1.8
://
u' = 4x/(-2x + 12y + 3)
v' = 9y/(-2x + 12y + 3)
tp
x = (27u'/4)/[(9u'/2) - 12v' + 9]
y = (3v')/[(9u'/2) - 12v' + 9]
ht
nits = cd/(m2) = Ft-L x 3.426
lux = foot-candle x 10.76
8
LCD Monitor General Specification
Model name X233H
Driving system TFT Color LCD
Active Display Area 509.76 (H) × 286.74(V)
Pixel pitch 0.2655(H) x 0.2655(W)
LCD Panel
Contrast Ratio 40000 : 1 Max(ACM)
Response time 5ms(Typ.)
Luminance of White 300(Typ.) cd/
Separate Sync. H/V TTL
t
ne
Input H-Frequency 30kHz 83kHz
V-Frequency 56-75Hz
el.
Viewing angle (H)90 (V) 90(Type)
Display Colors 16.7M
wj
Display mode 1920 x 1080 @60Hz
w.
ON Mode < 65W
EPA ENERGY STAR®
OFF Mode < 1W
ww
Set to factory preset value, which allows that the brightest two of 32 linear distributed
Contrast control
gray-scales (0 700mv) can be distinguished.
://
Power Source 100 V ~ 240 V50 ± 3Hz, 60 ± 3Hz
Operating Temp: 0° to 40°C
tp
Environmental Storage Temp: -20° to 60°C
Considerations Operating Humidity: 15% to 90%
Storage Humidity: 15% to 90%
ht
Peak surge current < 55A peak at 240 VAC and cold starting
No advance effects (no loss of information or defect) with a maximum of 1 half-wave
Power line surge
missing per second
9
LCD Panel Specification of X233H
General Specifications
t
ne
el.
wj
w.
Block Diagram
ww
TFT LCD Module
://
tp
ht
10
Back light Unit
t
ne
el.
Electrical Characteristics wj
w.
ww
://
tp
ht
11
Optical Specifications
t
ne
el.
wj
w.
ww
://
tp
ht
12
Factory Preset Timing of X233H
VESA MODES
Horizontal Vertical
Nominal Sync Nominal Sync Nominal
Frequency Polarity Freq. Polarity Pixel
Mode Resolution Total
+/- 0.5kHz +/- 1 Hz Clock
(MHz)
640x480@60Hz 800 x 525 31.469 N 59.940 N 25.175
VGA
640x480@72Hz 832 x 520 37.861 N 72.809 N 31.500
800x600@56Hz 1024 x 625 35.156 N/P 56.250 N/P 36.000
SVGA 800x600@60Hz 1056 x 628 37.879 P 60.317 P 40.000
800x600@72Hz 1040 x 666 48.077 P 72.188 P 50.000
1024x768@60Hz 1344x806 48.363 N 60.004 N 65.000
XGA
1024x768@70Hz 1328x806 56.476 N 70.069 N 75.000
1152x864@60Hz 1600 x 900 67.500 P 75.000 P 108.000
VESA 1280x960@60Hz 1800 x 1000 60.000 P 60.000 P 108.000
1280x720@60Hz 1650 x 750 44.955 P 59.940 P 74.176
t
SXGA 1280x1024@60Hz 1688 x 1066 63.981 P 60.020 P 108.000
ne
1280x800@60Hz 1680 x 831 49.702 P 59.810 N 83.500
WXGA
1360x768@60Hz 1792 x 795 47.712 P 60.015 P 85.500
WXGA+ 1440x900@60Hz 1904 x 931 55.935 N 59.887 P 106.5
WSXGA+ 1680x1050@60Hz 2240 x1089 65.290 N 59.954 P 146.250
el.
1600x1200@60Hz 2160 x 1250 75.000 P 60.000 P 162.000
1920x1080@60Hz 2576 x 1120 67.158 N 59.963 P 173.000
UXGA
1920x1080@60Hz 2200 x 1125 67.500 N 60.000 N 148.500
1920x1080@60Hz 2080 x 1111
wj 66.587 P 69.934 N 138.500
IBM MODES
DOS 720x400@70Hz 900 x 449 31.469 N 70.087 P 28.322
w.
MAC MODES
VGA 640x480@67Hz 864x525 35.000 N 66.667 N 30.240
ACER SPECIAL MODE
ww
[email protected] Hz 808 x 541 31.199 N 57.67 P 25.209
1024x600@60Hz 1312 x 622 37.320 N 60.000 N 48.964
://
tp
ht
13
Monitor Block Diagram
The LCD MONITOR will contain a main board, a power board, a usb board and a key board which house the flat
panel control logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Flat Panel and
CCFL Drive. CCFL backlight USB board
Main Board
Power Board
t
ne
AC-IN
100V-240V Key board
el.
DVI Signal D-SUB Signal
wj
w.
ww
://
tp
ht
14
Main Board Diagram
Panel Interface
(CN301)
t
ne
Scalar IC NT68667UFG/C QFP-128L
Keypad Interface
el.
(CN402)
(Include MCU, ADC, OSD)
(U401)
j
.w
H sync
V sync
D-Data RGB
D-Clock
ww
D-Sub
Flash Memory Connector
SST25VF010A-33-4C-SAE Crystal
DVI (CN101)
(U402) 12MHz
Connector
(X401)
w (CN102)
://
tp
ht
15
Software Flow Chart
1
Y
2 3
N
N
4
N
5
t
ne
Y
6
N
el.
wj 7 8
Y
w.
Y 9
ww
N
10 11
Y
://
N N
12 13
tp
Y Y
ht
N
14 15 16
Y
17
N
18 19
Y
16
Remark:
1) MCU initializes.
2) Is the EEPROM blank?
3) Program the EEPROM by default values.
4) Get the PWM value of brightness from EEPROM.
5) Is the power key pressed?
6) Clear all global flags.
t
7) Are the AUTO and SELECT keys pressed?
ne
8) Enter factory mode.
el.
9) Save the power key status into EEPROM.
Turn on the LED and set it to green color.
Scalar initializes.
wj
10) In standby mode?
w.
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
ww
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
://
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the
tp
message disappears.
ht
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
17
Main Board Layout
t
ne
el.
wj
w.
ww
://
Symbol Description Symbol Description
U401 IC NT68667UFG/C QFP-128L CN402 WAFER
tp
U703 IC AP1117D33L-13 TO252-3L DIODES CN701 WAFER 9P RIGHT ANELE PITCH
ht
U103 IC AZC099-04S SOT23-6L CN301 CONNECTOR
U104 IC AZC099-04S SOT23-6L X401 CRYSTAL 12MHz HC-49US ARG6-120
D-SUB 15PIN VERTICAL CONN WITH
U402 SST25VF010A-33-4C-SAE CN101
SCREW
U702 IC AZ1117D-1.8-E1 CN102 DVI 24PIN CONN F
18
Installation
ht
tp
://
19
ww
w.
wj
el.
ne
t
ht
tp
://
20
ww
w.
wj
el.
ne
t
Operating Instructions Chapter 2
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
· The power cord should be connected.
· Connect the video cable from the monitor to the video card.
· Press the power button to turn on the monitor position. The power indicator will light up.
External Controls
t
ne
el.
wj
Front panel controls
1. Power Switch:
w.
To turn ON or OFF the power.
2. Power LED:
ww
Lights up to indicate the power is turned ON.
3. Empowering / Exit:
1) When OSD menu is in active status, this button will act as EXIT-KEY(EXIT OSD menu).
://
2) When OSD menu is in off status, press this button to select scenario mode.
4. Auto Adjust button / Exit:
1) When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).
tp
2) When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The
Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.
ht
5. < / >
1) Press < or > to select the desired function. Press < or > to change the settings of the current function.
6. MENU / ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON.
21
eColor Management (OSD)
Operation instructions
Step 1: Press " Key" to open the Acer e-Color Management OSD and access the scenario modes
Step 2: Press "<" or ">" to select the mode
Step 3: Press "Auto Key " to confirm the mode and run Auto Adjust
t
ne
el.
wj
w.
ww
://
tp
ht
22
How to Adjust a Setting
t
ne
el.
wj
w.
ww
://
tp
ht
23
Adjusting the picture
t
ne
el.
wj
w.
ww
://
tp
ht
24
ht
tp
://
25
ww
w.
wj
el.
ne
t
How To Optimize The DOS-Mode
Plug And Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over
the DDC2B channel.
This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to
operate properly, there must be a video input signal.
t
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)
ne
and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no
video-input signal present. When there is no video input signals this monitor, following a time-out period, will
el.
automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video
input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to
wj
a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking the mouse
restores the display.
w.
Using the Right Power Cord
ww
The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed
and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of
://
a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type
attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates with a molded-on type
connector body, rated 10A, 250V, having standard CEE-22 female configuration.
tp
Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.
ht
Enter into the factory mode:
Turn off the power, press the "e-color" and turn the power on. The factory OSD will be at the left top of the panel.
26
Machine Disassembly Chapter 3
This chapter contains step-by-step procedures on how to disassemble the X233H monitor
for maintenance.
The tool for disassembly is as follows:
Screwdriver, hexagonal screwdriver, Putty knife.
Disassembly Procedure
1. Remove the hinge assembly.
t
ne
el.
wj
w.
ww
2. Remove the rear cover and bezel.
The arrows in blue are the hook that we should put attention to when remove the rear cover. Use plastic
putty knife to release hooks, then you can easily remove the rear cover.
://
tp
ht
27
t
3 Remove the lamp connectors and remove the screws to remove the panel. Put attention to the LVDS cable.
ne
el.
wj
w.
ww
://
4. Remove the screws to remove the main board and power board.
tp
ht
28
5. The panel
ht
tp
://
29
ww
w.
wj
el.
ne
t
Troubleshooting Chapter 4
This chapter provides troubleshooting information for the X233H:
1. No Power
No power
Press power key and look if the
picture is normal
NG
t
Please reinsert and make sure the
ne
AC of 100-240 is normal
el.
OK NG Reinsert or check the
wj power section
Measure U703 Pin2=3.3V,
w.
NG
ww
OK Check U703, C706 and C707
Check if X401 oscillate waveforms are
normal
://
NG
tp
Replace X401 OK
ht
Replace U401
30
2. No Picture (LED is orange)
No picture
The button if under NG NG
X401 oscillate
control waveform is normal Replace X401
OK
OK
Check reset circuit of NG Check Correspondent
U401 is normal component
Measure U703 Pin2=3.3V,
OK
t
ne
Replace U401
OK
el.
X401 oscillate NG
waveform is normal
wj
Check U703, C706 and C707
NG
Replace X401
w.
OK
Check HS/VS from
ww
CN101 is normal
NG
Check Correspondent
://
OK component
Replace U401
tp
ht
31
3. Panel Power Circuit
White screen
NG
Measure Q302 base X401 oscillate
is low level? waveform is normal
OK NG Replace X401
OK
t
ne
Check CN301is solder
and Q302,Q301 is OK? Check reset circuit of
U401 is normal
el.
NG Check Correspondent
NG
Check Correspondent component.
wj
component. OK
OK
w.
Replace U401
Replace PANEL
ww
://
tp
ht
32
4. Key Board
OSD is unstable or not working
NG
Is Key Pad Board connecting normally? Connect Key Board
Y
NG
Replace Button Switch
t
Is Button Switch normally?
ne
Y
el.
NG
Is Key Pad Board normally?
wj Replace Key Board
Y
w.
Check Main Board
ww
://
tp
ht
33
5. Power Board
1) No power
Check CN902 PIN3, 4 = 5V
NG
Check AC line volt 110V or 220V
OK NG
Check AC input
t
Check the voltage of C905 (+)
ne
OK NG
Check bridge rectified circuit and F901 circuit
Check start voltage for the pin3 of IC901
el.
wj
NG
OK Check R904, R905 and Change IC901
w.
ww
Check the auxiliary voltage is bigger than
11V and smaller than 25V
://
OK NG
1) Check IC901
2) Check R909/D901/C908/C907circuit
tp
Check IC901 pin8 PWM wave
ht
OK
NG
Check IC901
Check D906/D907/D908/IC903/Q903/ZD902
34
2.) No Backlight
Check if the input voltage of inverter part is 16V
OK NG
Check adapter part
Check ON/OFF signal
OK NG
Check Interface board
t
Check IC801 PIN12=14.5V
ne
OK
NG
el.
Check ON/OFF circuit
wj
Check IC801 PIN5 have triangle wave
w.
NG
OK Change IC801
ww
Check IC801 PIN9/PIN10 PWM wave
NG
://
OK
Check R816/R817/R818/R819
tp
Check the output of PT801
ht
OK
NG
Change PT801
Check connecter & lamp
35
Connector Information Chapter 5
t
ne
el.
wj
w.
ww
://
tp
ht
36
FRU (Field Replaceable Unit) List Chapter 6
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of X233H. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number
change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of
this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order
FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on
t
how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.
ne
Exploded Diagram (Model: X233H)
el.
wj
w.
ww
://
tp
ht
37
ITEM PART NO. DESCRIPTION Q`TY
1 BEZEL L23WA-8ACER3-S4 A34G1084 RXA1B0130 1
2 KEY BUTTON Q33G0237 RX 1L0100 1
3 LED LENS A33G0270 1 1L0100 1
4 KEY BOARD KEPC7QK1 1
5 PANEL LTM230HT01 A03(003) SZ SEC 750GLS230HT132N000 1
6 POWER BOARD PWPC8E41MQHU 1
7 MAIN BOARD CBPCRNDAEQ1 1
8 MAIN_FRAME_SAM A15G0563101102 1
9 MAIN_FRAME_SHIELD A85G0141101 1
10 REAR COVER L23WA-8ACER3-S4 A34G1085 RX 3B0100 1
11 HINGE COVER L A33G0271 RX 1L0200 1
12 HINGE COVER R A33G0271 RX 2L0200 1
13 SPK 8OHM 2W 40X20X18 350 320MM KUAIDA 078G 518501 K 1
t
14 USB BOARD USB7QK4 1
ne
15 SCREW 0Q1G 130 8120 7
16 SCREW 0M1G 130 6120 2
el.
17 SCREW 0M1G 140 8125 4
18 STAND FRONT A34G0473 RX 1B0100 1
19 HINGE A37G0050 4 1
wj 1
20 STAND REAR A34G0474 RX 1B0100
21 BASE A34G0475 RX 1B0130 1
22 BASE BKT A15G0263201 1
w.
23 BASE BUTTON A33G0266 RX 1L0100 1
24 RUBER FOOT-1 A12G0006 1 1
ww
25 RUBER FOOT-2 A12G0007 1 2
26 SCREW 0Q1G 140 10120 6
27 SCREW 0Q1G 130 8120 8
://
tp
ht
38
Part List
Above picture show the description of the following component.
Picture Description Part No.
Main_frame_Sam A15G0563101102
t
ne
el.
wj Bezel A34G1084 RXA1B0130
w.
ww
://
Panel 750GLS230HT132N000
tp
ht
Power Board PWPC8E41MQHU
39
Main Board CBPCRNDAEQ1
Key Board KEPC7QK1
t
ne
el.
wj
Stand Front A34G0473 RX 1B0100
w.
ww
://
Base A34G0475 RX 1B0130
tp
ht
Stand Rear A34G0474 RX 1B0100
40
Hinge A37G0050 4
t
USB BOARD USB7QK4
ne
el.
wj
w.
ww
://
tp
ht
41
Schematic Diagram Chapter 7
Main Board
FB102
VGA_B+ 1 2 R105 100R 1/16W 5% C102
BEAD 0.047uF DSUB_B+
H_Sy nc R102 R103 1K 1/16W 5%
V_Sy nc DSUB_H
100R 1/10W 5% R104 1K 1/16W 5% R108 C105
DSUB_V
5pF/50V
E5VCC 75R 1/16W 5%
R106 R107 C103 C104
VGA_B- R109 100R 1/16W 5% C106
DSUB_B-
2K2 1/16W 5% 2K2 1/16W 5% 22pF 22pF 0.047uF
t
5V_ESD
U104
ne
DSUB_SDA 6 1 H_Sy nc R110 470R 1/16W 5% C107
I/O4 I/O1 DSUB_SOG
R143 R144 5 2 FB103 1000pF
4K7 1/16W 5% 4K7 1/16W 5% CN101 DSUB_SCL 4 VDDGND 3 V_Sy nc
I/O3 I/O2 VGA_G+ 1 2 R111 100R 1/16W 5% C108
16
DSUB_G+
DSUB_5V BEAD 0.047uF
100R 1/16W 5% 10 C112 AZC099-04S
R101 DSUB_SCL 15 5 VGA_PLUG NC R112 C109
DDC1_SCL DSUB_5V
9 5pF/50V
14 4 75R 1/16W 5%
el.
8 VGA_B- U1 03
13 3 VGA_B+ VGA_G- R114 100R 1/16W 5% C110
VGA_G- DSUB_G-
7 ZD104 ZD105 0.047uF
DSUB_SDA 12 2 VGA_G+ RLZ5.6B
DDC1_SDA RLZ5.6B U103
R113 6 VGA_R- 5V_ESD
100R 1/16W 5% 11 1 VGA_R+ VGA_R+ 3 4 VGA_B+