Text preview for : Advent 30.3461_service_manual.pdf part of Advent 30.3461 CRT TV
Back to : Advent 30.3461_service_ma | Home
SERVICE
MANUAL
CONTENTS
1. INSTRUCTION..........................................................................................1
2. ALIGNMENT PROCEDURE..........................................................................2
3. FOR FACTORY MENU ADJUSTMENT SEE CHART5~CHART11.........................5
4. GENERAL DESCRIPTION OF THE SDA 9380-B21..........................................11
5. INTRODUCTION OF THE VPC 3230D........................................................13
6. INTRODUCTION OF THE MSP 3425G.........................................................15
7. GENERAL DESCRIPTION OF THE PW1235................................................16
8. GENERAL DESCRIPTION OF THE TDA6111Q.............................................19
9. GENERAL DESCRIPTION OF THE SiI907B...................................................21
WIRING DIAGRAM..................................................................................22
BLOCK DIAGRAM....................................................................................23
SCHEMATIC DIAGRAM............................................................................24
ELECTRICAL PARTS LIST........................................................................29
0
CAUTION: THIS SERVICE MANUAL IS ONLY FOR PROFESSIONAL SERVICE PERSONNEL'S
REFERENCE. BEFORE SERVICING THIS CHASSIS, PLEASE READ THE
FOLLOWING NOTICE ITEMS.
1. INSTRUCTION
Before servicing and aligning this equipment, please read the following "X-RAY RADIATION
PRECAUTION" ,"SAFETY PRECAUTION" and "PRODUCT SAFETY NOTICE".
1.1 X-RAY RADIATION PRECAUTION
1) Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such
hazards, the high voltage must not be above the specified limit. The normal value of the high
voltage of this receiver see below chart:
Chart 1 High voltage requirement
High voltage normal
Model Utmost value Beam current
value
T306 30 kV ±1 kV 35 kV 1.6 mA
T346 30 kV ±1 kV 35 kV 1.6 mA
2) Each time a receiver requires servicing, the high voltage should be checked following the HIGH
VOLTAGE CHECK procedure in this manual. It is recommended the reading of the high voltage be
recorded as a part of service record. It is important to use an accurate and reliable high voltage
meter.
* When checking, main power (B+) should be kept at 135 V (for Toshiba pure flat CRT).
3) The primary source of X-RAY RADIATION in this TV receiver is the picture tube. For continuous
X-RAY RADIATION protection, the replacement tube must be exactly the same type tube as
specified in the parts list.
4) Some parts in this receiver have special safety-related characteristics for X-RAY RADIATION
protection. For continuous safety, parts replacement should be undertaken only after referring to
the PRODUCT SAFETY NOTICE below.
1.2 SAFETY PRECAUTION
WARNING:
Service should not be attempted by anyone unfamiliar with the necessary precaution on this receiver.
The following are the necessary precautions to be observed before servicing this chassis.
1) Since the power supply circuit of this receiver is directly connected to the AC power line, an
isolation transformer should be used during any dynamic service to avoid possible shock hazard.
2) Always discharge the picture tube anode to the CRT conductive coating before handling the
picture tube. The picture tube is highly evacuated and if broken, glass fragments will be violently
expelled. Use shatter proof goggles and keep picture tube away from the unprotected body while
handling.
1
3) When replacing a chassis in the cabinet, always be certain that all the protective devices are put
back in place, such as: non-metallic control knobs, insulating covers, shields, isolation
resistor-capacitor network etc.
4) When replacing parts or circuit boards, disconnect the power cord.
5) When replacing a high wattage resistor (oxiode metal film resistor) on the circuit board, keep the
resistor 10mm (1/2in) away from circuit board.
6) Connection wires must be kept away from components with high voltage or high temperature.
7) If any fuse in this TV receiver is blown, replace it with the FUSE specified in the chassis parts list.
1.3 PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the chassis have special safety-related characteristics.
These characteristics are often passed unnoticed by a visual inspection and the X-RAY RADIATION
protection afforded by them cannot necessarily be obtained by using replacement components rated
for higher wattage, etc. Replacement parts which have these special safety characteristics are
identified in this manual and its supplement electrical components having such features are shaded
on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of
substitute replacement parts which do not have the same characteristics as specified in the parts list
may create shock, fire, X-RAY RADIATION or other hazards.
1.4 Testing equipment
HDTV signal generator: VG853/K7253 or other same type, 1 set.
Signal generator: PM5515 or the same type, 1 set.
Voltameter: FULK805A or the same type, 1 set.
White balance alignment equipment: 1 set
Standard testing jigs: 1 set.
Geometry alignment equipment: 1 set.
Alignment stick: 1 set.
Degaussor: 1 set.
2 Alignment procedure
2.1 Instruction
a) In this chassis since there are a great amount of data needed to be set, these setting all are stored
in E2PROM. To reduce the alignment working, use the aligned E2PROM as a female parent to
copy and then use them. Or refer to appendix chart and preset E2PROM value and then use.
b) To conduct the alignment, the power supply should be AC120 V, 60 Hz. The whole unit should be
preheated for 30 minutes.
c) To conduct with color purity, convergence, white balance alignment or other alignment relative to
color, the CRT should be degaussed thoroughly.
d) Since this chassis adopts modulization structure, before mounting, every module should be
conducted with alignment.
e) The factory menu's alignment should use XOCECO RC-T03-0A remote control. Press power
switch to turn on the set, in turn press button "SLP-MUTE-AV-MENU" to enter into factory menu.
2
Press SLP or 0 button to exit. Press MUTE button to preset before Out-factory.
f) For the supporting mode in this set see below chart 2.
Chart 2 The supporting mode in this set
Working mode Mode instruction H-frequency V-frequency Alignment instruction
Hz Hz
TV TV mode 33.75k 60 Adjust firstly, every item should
adjust
1920*1080i/33.75K American HDTV mode 33.75k 60 Horizontal and vertical parameter,
white balance
720P*576/45.125K American HDTV mode 33.75k 60 Horizontal and vertical parameter,
white balance
640*480i (YCrCb) YcbCr 33.75k 60 Horizontal and vertical parameter,
(15.7K,59.97HZ) white balance
640*480p (YPrPb) Progressive DVD 33.75k 60 Horizontal and vertical parameter,
(31.5K,60HZ) white balance
800*600(SVGA) DVI mode 33.75K 60 Horizontal and vertical parameter,
white balance
1024*768(XGA) DVI mode 33.75K 60 Horizontal and vertical parameter,
white balance
2.2 Alignment procedure
2.2.1 Module alignment
In all the module alignment, use a normal working TV set as an alignment frock, pull the set's
corresponding module and keep it as an example. Insert the module wanted to be check,
then apply power to alignment.
a) AV board module
AV interface function check: check all the AV input/outputs function, it should meet the Product
Standard requirements.
b) Digital processing board module
No alignment point, apply the power and check whether S-VIDEO, YCbCr, YpbPr input is normal.
c) Main board
No alignment point. Apply the power and measure "B+" voltage, the reading should be 105V,
check there are no assemble error, the OSD, SVM is normal, and it is OK.
2.2.2 Chassis adjustment
Correctly insert all modules and parts, connect CRT board parts to CRT, apply power and
check B+ voltage, the reading should be 105V. (on J332/J305)
2.2.3 The whole unit adjustment
Be sure the whole unit has been preheated for 30 minutes.
a) Focus adjustment
1) In TV mode receive crosshatch signal, at the same time set SVM to OFF.
2) Adjust FOCUS inductance L306 on Dynamic Power Board to make R323 dynamic focus
voltage be 1KV+/-50V.
3) Adjust FOCUS potentiometer on FBT and CRT to make horizontal and vertical grid both
thinnest, and consider horizontal grid mainly.
4) Set SVM to ON, check the whole effect.
3
b) Dark current (SCREEN voltage) adjustment
In TV mode receive gray scale signal, after entering into factory menu status, press "1" button to
enter into "FACTORY MENU 1" factory menu, first preset WHITE-R, WHITE-G, WHITE-B's value
all to 0, adjust SCREEN potentiometer to make SCREEN LOCK on the screen lower part display
OK and it is OK, at this time, if changing channel, it should not appear flyback line. This state
should also be OK after finish adjusting the white balance. .
c) White balance adjustment
Adjust on the basis of the above step, at standard status use gray scale signal to adjust.
1) Press "1"button to firstly adjust TV input white balance: fix the testing point at about 40 nits gray
scale, then by adjusting WHITE-R,WHITE-G and WHITE-B to make the value meet chart 3's
requirement.
2) Press "5" button to adjust YpbPr input white balance: use oscilloscope to measure Y signal
output on Digital Processing Board. Adjust G-0 gray scale to make blanking level be even with
black level, adjust G-G to make signal amplitude to be 0.7V and eight level gray scale be even,
then adjust R-G, B-G, R-0, B-0's value to make white balance meet chart 3's requirement.
Chart 3: chroma coordinates requirements
Colour temperature 12000K
X coordinate 0.270±0.008 MPDC
Y coordinate 0.283±0.008 MPDC
d) Picture size position and high voltage adjustment
In component mode input 1080I signal
(1) Use crosshatch and electrical circle signal, after entering into factory menu status, press "2"
button to enter into "FACTORY MENU 2" factory menu to adjust picture's linearity. Adjust
R339 joint point to make the V-center deflection range be within ±5MM(T346), or
±3MM(T306).
(2) Change the signal to white background, or greatly change contrast and brightness, or press
PIC button to switch among several kinds of analogue amount to make corresponding
beam current changes, adjust V-EHT-COM, H-EHT-COM to make raster's size basicly not
change when at different beam current status.
3) According to chart 2 in turn apply every testing signal (firstly apply YpbPr signal, then TV or AV
signal), then press "5" button to enter into "FACTORY MENU 5", adjust H-S, V-S, H-SIZE, V-SIZE to
make picture normal.
e) Sub-brightness adjustment
Receive split field signal, set colour/contrast/brightness to 0, check whether screen second gray is
slightly bright, otherwise press "6" button, in factory menu select CONTRAST MAX and BRIGHT
MAX to adjust.
f) Filament/beam current/high voltage check and adjustment
1) Filament voltage: receive a TV program signal, set picture mode to "STANDARD",the filament
voltage effective value should be 6.3±0.2 Vrms.
2) Beam current check: receive all white field signal, set picture mode to "SPORTS", measure
R360 two terminals' voltage and the reading should be less than or be equal to 1.6V. If not,
after entering into factory menu status, press "4" button to enter into "RGB MENU" factory
menu, adjust AV BEAM LIMIT item to make beam current meet requirements.
4
3) High voltage check: receive D8 signal, set picture mode to "STANDARD", measure CRT high
voltage and the reading should be A value in chart 3. When brightness, contrast is set to
minimum (zero beam current), measure the high voltage, the reading should not exceed B
value in chart 4.
Chart 4 High voltage check requirements
CRT Size
Parameters
81 cm(T306) 92 cm(T346)
A 30 kV±0.5 kV 30 kV±0.5 kV
B 34+ kV 34 kV
4) High voltage protection: receive a picture signal, adjust until picture and sound are normal,
short R340 and the circuit should immediately enter into power-off protection state and the
state should keep. Turn off the power switch and then turn on, the picture and sound should
restore to before-testing state.
g) Peak value adjustment
On the condition of SCREEN and beam current has been adjusted properly, in order to show
picture's contrast well and control picture's colour tail, apply a little beam current picture (for
example, black and white crosshatch) and set picture's contrast and brightness to maximum, then
after entering into factory menu status, press "4" button to enter into "RGB MENU" factory menu,
by adjusting PEAK DRIVE LIMIT item to make the whole unit's picture colour just without colour tail
on the condition of maximum contrast and it is OK.
h) Every control buttons' check
Check according to Instruction manual.
i) Check all the input/output terminals' function, please check according to "PRODUCTION
STANDARD"
i) Out-factory setting
Set picture to "Standard".
Set sound to "Music".
Set Blue back to ON.
Set OSD language to English.
Set DNR to SOFT.
Set SVM to ON.
Set Volume to 30.
Set Loudness to OFF.
Set AVC to ON.
Set CCD to OFF.
Set child lock password, V-chip password to 0000.
Set V-chip all rating to no rating .
Set the channel to Cable 3. .
5
3 For factory menu adjustment see Chart 5~Chart 11.
Chart 5 Factory menu (1)WRITE
Default
Item name Item instruction Range Adjusting method
value
WRITE R Bright balance R BF-3F Refer to white balance adjustment part 1
WRITE G Bright balance G BF-3F Refer to white balance adjustment part 1
WRITE B Bright balance B BF-3F Refer to white balance adjustment part 1
SCREEN Dark current
OK/OFF OK Adjust SCREEN potentiometer until OK
LOCK adjustment
2003-XX-XX Version date fix
Chart 6 factory menu (2)
Default
Item Item instruction Range Adjustment method
value
V SIZE V-size 80-7F 39 To make vertical reproduction rate reach
90%-92%
V SHIFT V-center 80-7F 17 To make picture center and CRT center be
in accordance
V LINEAR V-linearity 80-7F 41 To make V-linearity distortion minimum.
V S CORR Vertical S-correction 80-7F F7 To make vertical S-correction distortion
minimum.
H SIZE H-size 80-7F 08 To make horizontal reproduction rate reach
90%-92%
H SHIFT H-center 80-7F 43 To make picture horizontal center be in
accordance with CRT center.
V ANGLE Parallelogram correction 80-7F 05 To correct parallelogram distortion
V BOW Arch correction 80-7F 0E To correct arch distortion
PIN AMP Pincushion correction 80-7F 60 To make pincushion distortion minimum
PIN PHASE Trapezoid correction 80-7F AE To make trapezoid distortion minimum
UP Upper edge corner 80-7F 11 To correct upper two corners distortion
CORNER correction
LOWER Lower edge corner 80-7F C5 To correct lower tow corners distortion
CORNER correction
EXT Edge and corner 80-7F C5 Corner edge correction
CORNER correction
V SYNC 80-7F 20
CONT
Chart 7: factory menu (3)
Default
Item Item instruction Range Adjustment method
value
V SCROLL Vertical scroll 0-FF 00 Not adjust, set default value
V ASPECT V-size 0-FF 00 Not adjust, set default value
V EHT Vertical high 80-7F BD To make vertical raster size not change
voltage correction when beam current changes greatly.
6
H EHT Horizontal high 80-7F 9D To make horizontal raster size not change
voltage correction when beam current changes greatly.
AFC EHT COM High voltage auto 20-1F 08 Not adjust, set default value
frequency control
H BLANK TIME Horizontal 80-7F E4 Not adjust, set default value
blanking width
H BLANK PHASE Horizontal 80-7F F9 Not adjust, set default value
blanking phase
V BLANK START V-sync phase 80-7F FB Not adjust, set default value
V BLANK END V-sync phase 80-7F 11 Not adjust, set default value
MIN NO.OF LINE H-blanking phase 80-1F 00 Not adjust, set default value
MAX NO.OF LINE H-blanking end 80-7F FF Not adjust, set default value
position
PWM CONTROL H-blanking width 80-7F 02 Not adjust, set default value
PLL CONTROL 0 H-blanking width 80-7F 0B Not adjust, set default value
PLL CONTROL 1 H-blanking width 80-7F 62 Not adjust, set default value
Chart 8 Factory menu (4)RGB MENU
Default
Item Item instruction Range Adjustment method
value
INT H-SYNC H-sync phase 80-7F 12 Not adjust, set default value
PHASE
AV BEAM LIMIT Beam current limit 80-7F 1A Refer to beam current adjustment part
AV BEAM LIMIT Beam current limit 80-7F 81 Refer to beam current adjustment part
CHA
PEA DRIVE LIMIT Peak value limit 80-7F 00 Refer to peak value adjustment part
PEAK DRIVE TOP Top peak value 80-7F 10 Not adjust, set default value
limit
PEA DRIVE Bottom peak 80-7F 47 Not adjust, set default value
BOTTOM value limit
PEA DRIVE L-R Left/right edge 80-7F 88 Not adjust, set default value
peak value limit
DEFLECT 0 80-7F 03 Can not adjust, set default value
DEFLECT 1 80-7F 05 Not adjust, set default value
RGB CONTROL 0 80-7F 84 Not adjust, set default value
RGB CONTROL 1 80-7F 18 Not adjust, set default value
RGB CONTROL 2 80-7F 20 Not adjust, set default value
RGB CONTROL 3 80-7F 03 Not adjust, set default value
V INPUT MODE 80-7F 85 Not adjust, set default value
7
Chart 8 factory menu FACTORY 5(HDTV mode)
Default
Item Item insturction Range Adjustment method
value
R-G Red gun gain 00-FF 80 Refer to white balance adjustment part2
G-G Green gun gain 00-FF 80 Refer to white balance adjustment part2
B-G Blue gun gain 00-FF 80 Refer to white balance adjustment part2
R-O Red gun bias value 00-FF 80 Refer to white balance adjustment part2
G-O Green gun bias value 00-FF 80 Refer to white balance adjustment part2
B-O Blue gun bias value 00-FF 80 Refer to white balance adjustment part2
H-S H-phase 00-FF Geometrical adjustment
V-S V-phase 00-FF Geometrical adjustment
H-SIZE H-size 00-FF Geometrical adjustment
V-SIZE V-size 00-FF Geometrical adjustment
Chart 9: factory menu 6
Default
Item Item instruction Range Adjustment method
value
CONTRAST Contrast maximum 00-7F 7F Not adjust, set to default value
MAX
CONTRAST Contrast center value 00-7F 3F Not adjust, set to default value
CEN
CONTRAST Contrast minimum value 00-7F 00 Not adjust, set to default value
MIN
BRIGHT Brightness maximum value 00-7F 7F Not adjust, set to default value
MAX
BRIGHT Brightness center value 00-7F 3F Not adjust, set to default value
CEN
BRIGHT Brightness minimum value 00-7F 00 Not adjust, set to default value
MIN
COLOR Colour maximum value 00-7F 3F Not adjust, set to default value
MAX
COLOR Colour center value 00-7F 20 Not adjust, set to default value
CEN
COLOR MIN Colour minimum value 00-7F 00 Not adjust, set to default value
SHARP Sharpness maximum 00-7F 7F Not adjust, set to default value
MAX value
TINT CEN Tint center value 00-7F 00 Not adjust, set to default value
Chart 10 Factory menu 7
Default
Item Item instruction Range Adjustment value
value
VOLUME-1 Sound curve 00-7F 0F Not adjust, set to default value
VOLUME-25 Sound curve 00-7F 1F Not adjust, set to default value
VOLUME-50 Sound curve 00-7F 3F Not adjust, set to default value
VOLUME-100 Sound curve 00-7F 7F Not adjust, set to default value
8
BASS MAX Bass maximum value 00-7F 7F Not adjust, set to default value
BASS MIN Bass minimum value 00-7F 00 Not adjust, set to default value
TREBLE MAX Treble maximum value 00-7F 7F Not adjust, set to default value
TREBLE MIN Treble minimum value 00-7F 00 Not adjust, set to default value
SURROUND Surround sound 00-7F 7F Not adjust, set to default value
MAX maximum value
SURROUND Surround sound 00-7F 00 Not adjust, set to default value
MIN minimum value
BLANCE CEN Balance center value 00-7F 20 Not adjust, set to default value
LOUDNESS Setting value when 00-7F 7F Not adjust, set to default value
ON loudness is on
LOUDNESS Setting value when 00-7F 00 Not adjust, set to default value
OFF loudness is off
Chart 11 Factory menu 8
Default
Item Item insruction Range Adjustment method
value
OSD-HP MENU phase 00-7F 00 Not adjust, set to default value (after
MENU adjustment, open the menu again and it
is effective)
OSD-HP AV AV menu phase 00-7F 00 Not adjust, set to default value(after
SEL adjustment, open the AV selection menu
again and it is effective)
OSD-HP Other menu phase 00-7F 00 Not adjust, set to default value (after
NORMAL adjustment, open the OSD again and it is
effective)
SVM DELAY SVM delay phase 00-7F 03 Not adjust, set to default value (after
adjustment, turn on the set again and it is
effective)
ZOOM DATA 169 picture zoom 80-7F 20 Not adjust, set to default value(after
adjustment, turn on the set again and it is
effective)
OPTION OPTION 00-FF 01 Not adjust, set to default value
DATA1
H-MUTE Horizontal failure of 00-FF 5A Not adjust, set to default value. If less than
DELAY oscillations time delay 10, the screen will light and burn the tube.
amount
9
Chart 12 Factory menu 9 DESIGN MENU
Default
Item Item instruction Range Adjustment method
value
IC XXX Relative IC chip
ADD H Address high 8 byte 00-FF Press VOL+/- button to change
ADD L Address high 8 byte 00-FF Press VOL+/- button to change
DATA H Data high 8 byte 00-FF Press VOL+/- button to change
DATA L Data lower 8 byte 00-FF Press VOL+/- button to change
READ Reading current data YES/NO
REFRESH Reflesh changed data YES/NO
SAVE Save changed data YES/NO
10
4.General description of the SDA 9380B21.
The SDA 9380 is a highly integrated deflection controller and RGB video processor for CTV
receivers with 15 to 19kHz or 31 to 38kHz line frequencies. The deflection component controls
among others a horizontal driver circuit for a flyback line output stage, a DC coupled vertical
saw-tooth output stage and an East-West raster correction circuit. All adjustable output
parameters are I²C-Bus con-trolled. Inputs are HSYNC and VSYNC. The HSYNC signal is the
reference for the internal clock system which includes the 1 and 2 control loops.
Block diagram of the SDA 9380-B21:
11
PIN CONFIGURATION:
12
5.Introduction of the VPC 3230D.
The VPC 3230D is a high-quality, single-chip video front-end, which is targeted
for 4:3 and 16:9, 50/ 60 and 100/120 Hz TV sets. It can be combined with other
members of the DIGIT3000 IC family (such as DDP 33x0A/B, TPU 3040) and/or
it can be used with 3rd-party products.
Block diagram of the VPC 3230D:
13
PIN CONFIGURATION:
14
6.Introduction of the MSP 3425G.
The MSP 3425G family of single-chip Multistandard Sound Processors covers the sound
processing of all analog TV standards worldwide, as well as the NICAM digital sound standards.
The full TV sound processing, starting with analog sound IF signal-in, down to processed analog
AF-out, is performed in a single chip.
Simplified functional block diagram of the MSP 3425G:
PIN CONFIGURATION:
15
7.General description of the PW1235.
The PW1235 Video Signal Processor is a high quality, digital video signal processor that
incorporates Pixelworks' patented, state-of-the-art video deinterlacer and scaler. Using
sophisticated algorithms, the PW1235 is able to effectively deinterlace video input by creating
motion vectors that follow frame-to-frame movement, and provide clear, progressive output in
both analog and digital formats.
With support for NTSC and PAL video formats, the PW1235 can be designed into any TV,
monitor, or projector application. Support for 3:2 and 2:2 film mode detection enables the
PW1235 to provide the best quality display for existing film and video standards. The PW1235
can dynamically enter or exit film mode (with flexible programming) to display mixed content with
the best possible quality.
As a single device, the PW1235 integrates many functions onto one chip. It has embedded a
scaler, an advanced deinterlacer, memory controller, color space converter, and Digital-to-Analog
Converter (DAC) onto one chip. There are two video input ports--a primary video port and a
secondary input port--that are used to accept YUV video in the ITU-R601 and ITU-R656 formats
respectively. Video content is analyzed on a single-pixel granularity to detect presence or
absence of noise and compute the amount of motion. Motion video is processed using a highly
intelligent algorithm that simultaneously eliminates noise and interpolates pixels along any angle
to produce a noise-free picture without jagged-edge artifacts.
As part of a Pixelworks solution, combining the PW1235 with a Pixelworks ImageProcessor
(such as the PW113, PW166 or PW181) offers the world`s best combination of deinterlacing and
16
scaling of video or graphics. This combination of high quality deinterlacing and scaling is
essential for higher resolution outputs such as XGA, SXGA, and UXGA that need to display
NTSC and PAL video.
Internal block diagram of the PW1235:
17
PIN CONFIGURATION:
18
8.General description of the TDA6111Q.
The TDA6111Q is a video output amplifier with 16 MHz bandwidth. The device is contained
in a single in-line 9-pin medium power (DBS9MPF) package, using high-voltage DMOS
technology, intended to drive the cathode of a colour CRT.
Block diagram of the TDA6111Q:
PIN CONFIGURATION:
19
20
9.General description of the SiI907B.
The SiI 907B Digital CRT Controller uses PanelLink Digital technology to support HDTV and
highresolution CRT monitors for DTV and PC applications.
The SiI 907B Controller integrates a 165 Megapixels/sec PanelLink receiver core with a
triple 10-bit, 175MHz DAC into a single chip for the highest quality possible on a CRT display. It
features support for High-bandwidth Digital Content Protection (HDCP), enhanced jitter
tolerance, and flexible, low power standby modes. Integrated, pre-programmed HDCP
keys provide the most secure solution while simplifying the design and manufacturing process.
PanelLink Digital technology is the world's leading DVI solution. PanelLink simplifies DTV and
PC display interface design by resolving many of the system level issues associated with
high-speed mixed signal design, providing the system designer with a digital interface solution
that is quicker to market and lower in cost.
SiI 907B Pin Diagram:
21
WIRING DIAGRAM
22
DVI
in
L3 R3
AC 120V
EHT
N401 TDA6110Q CRT
Vddh
GND
Vddl
Von
Vcn
Iom
Vfb
Vip
Vin
CRT BOARD L404 R417 560/C
R
1
2
3
4
5
6
7
8
9
1UH
L405 R419 560/C
G CRT SCREEN
560P/500V
C412
1UH
L403 R408 560/C
B
1UH
100N/250V
C413
C408
C407
H1 H2 G1G2G3G4
100N
22N
R418 R421
R411 R407 2.2/2W 2.2/2W
750 51K/1W
R420
C411
SG404 300V
SG402 300V
C409 2.2M
SG404 2KV
SG401 300V
104 R410 C410
1.8K 100U 100N
VR401
R413 20M
100
X401 D401
HZ12B1 R409 Focus
12V 1
GND 2 2K N402 TDA6110Q G2
R 3
Vddh
GND
Vddl
Von
103/2KV C421
Vcn
Iom
Vfb
Vip
Vin
G 4
B 5
GND 6
1
2
3
4
5
6
7
8
9
D 7 L407
SP 8 R414 V401 22UH
10K C1815
560P/500V
C419
TO MAIN
100N/250V
C415
C414 L409
C416 22UH
100N X403
L408
22N
22UH
R412 R416
750 51K/1W
R415 C418
100U 100N TO CRT GRAND
1.8K C417
CAUTION:
All the parts in the schmatic diagram marked
N403 TDA6120Q with the sign of are extremely important
Vddh
GND
Vddl
Von
Vcn
Iom
Vfb
for safety.
Vip
Vin
The schmatic diagram is representative only.
1
2
3
4
5
6
7
8
9
The value of the parts will be changed with the
L402
improvement of the circuit.
22UH C420
100N/250V
560P/500V
C405
C406
33UF/250V
1. The unit of resistance is ohm.
X402
200V 6 K=1,000 ohm M=1,000,000 ohm
5 C401 R405 C402
4 1K 100N
3 2. The unit of inductance is H.
2 22N
6.3V 1 mH=1/1,000H uH=1/1,000mH
L406 R401 R404
0.27UH
TO MAIN 750 51K/1W
L401 3. The unit of capacitance is F.
10UH
uF=1/1,000,000F pF=1/1,000,000uF
C404
R403 C403
1.8K 100U 100N 4. The meaning of the symbols is below:
small signal ground
large signal ground
+9V
+9V
R2
YOM
L0
VIM