Text preview for : 070-3921-00_8540_Installation_Oct81.pdf part of Tektronix 070-3921-00_8540_Installation_Oct81 Tektronix 85xx 8540 070-3921-00_8540_Installation_Oct81.pdf
Back to : 070-3921-00_8540_Installa | Home
INSTRUCTION MANUAL
COMMITTED TO EXCELLENCE
WARNING
THE FOLLOWING SERVICING INSTRUCTIONS
ARE FOR USE BY QUALIFIED PERSONNELONLY.
TO AVOID PERSONAL INJURY, DO NOT
PERFORM ANY SERVICING OTHER THAN THAT
CONTAINED IN OPERATING INSTRUCTIONS
UNLESS YOU ARE QUALIFIED TO DO SO.
PLEASE CHECK FOR CHANGE INFORMATION
AT THE REAR OF THIS MANUAL.
Tektronix, Inc.
P.O. Box 500
Beaverton, Oregon 97077 Serial Number _ _ _ _ _ __
070-3921-00 First Printing OCT 1981
priv:11,eges' are reserved.
Printed in U.S.A.
8540 Installation
PREFACE
INTRODUCTION
This manual contains information on how to install an 8540 Integration Unit.
Since this is an Installation Guide, and not a User's Manual, this book
contains few operating instructions other than those required to perform
system verification.
The 8540 Integration Unit should be installed by a Tektronix Field Service
Specialist. Tektronix, Inc. is not obligated to furnish service to repair
damage resulting from attempts by unauthorized personnel to install this
product. Please call your nearest Tektronix Field Service Office for
installation.
ABOUT THIS MANUAL
This manual supports installation and verification of the 8540 Integration
Unit. Specifically, the sections in this manual provide the following
information:
Section An overview to the 8540 Integration Unit.
Section 2 Specifications for the 8540 Integration Unit.
Section 3 Instructions on unpacking the 8540 and setting up a work site.
Section 4 8540 front and rear panel controls, connectors, and indicators.
Section 5 Verification ~at the 8540 Integration Unit is working
properly.
Section 6 How the 8540 is configured when operating with other equipment.
Section 7 8540 Integration Unit circuit board configurations.
@ i
8540 Installation
NOMENCLATURE
Throughout this manual, the following terms are used for the sake of brevity.
Term: Meaning
===========l==========================================
8540 l 8540 Inte~ration Unit
i ~
I
8560 l
1
8560 Multiuser Software Development Unit
1
System I The terminal used for command entry
Terminal l and connected to the 8540
____________ 1_____________________________________________
1
CHANGE INFORMATION
Change notices are issued by Tektronix, Inc., to document changes in the
manual after it has been published. Change information is located in the
back of this manual, following the yellow tab marked "CHANGE INFORiviATION &
TEST EQUIPMENT". When you receive this manual, enter any change information
into the body of the manual, as indicated on the change notice.
REVISION HISTORY
As this book is revised and reprinted, reVlSlon history information is
included in the text and diagrams. Original manual pages are indicated by
the "@" symbol at the bottom inside corner of the page. Existing pages of
manuals that have been revised are indicated by a revision code and date (REV
B SEP 1981) in place of the "@" symbol. New pages added to an existing
section, whether they contain old, new, or revised information, contain the
"@" symbol alongside the revision date (@ SEP 1981).
MANUAL OVERVIEW
The 8540 Integration Unit is supported by a vRriety of user and servicing
manuals. 8540 user manuals contain operating instructions for the 8540, and
are standard accessories. 8540 servicing manuals consist of installation and
service manuals. The installation manual contains instructions for 8450
installation and system verification. This manual is a standard accessory.
The 8540 service manual contains servicing information for the basic 8540
configuration. Service manuals are optional accessories that must be ordered
separately.
ii @
8540 Installation
CONTENTS
Section 1 -- 8540 OVERVIEW
Page
In trod uction ..