Text preview for : 070-5049-00_TNIX_8560_Series_Hardware_Installation_Guide_Mar84.pdf part of Tektronix 070-5049-00 TNIX 8560 Series Hardware Installation Guide Mar84 Tektronix 85xx 856x 070-5049-00_TNIX_8560_Series_Hardware_Installation_Guide_Mar84.pdf



Back to : 070-5049-00_TNIX_8560_Ser | Home

SERV'CE Part No. 070-5049-00
TEK MANUAL Product Group 61



C;60 Series
Multi-User Software
Development
Unit




TNIX
8560 Series
Hardware
Installation
Guide




Please check for change information
at the rear of this manual



First Printing MAR 1984 Tektron~
WARNING
THE FOLLOWING SERVICING INSTRUCTIONS
ARE FOR USE BY QUALIFIED PERSONNEL ONLY.
TO AVOID PERSONAL INJURY, DO NOT PER-
FORM ANY SERVICING OTHER THAN THAT CON-
TAINED IN OPERATING INSTRUCTIONS UNLESS
YOU ARE QUALIFIED TO DO SO. REFER TO OP-
ERATORS SAFETY SUMMARY AND SERVICE
SAFETY SUMMARY PRIOR TO PERFORMING ANY
SERVICE.




Copyright @) 1984 by Tektronix, Inc. All rights reserved.
Contents of this publication may not be reproduced in any
form without the permission of Tektronix, Inc.

Products of Tektronix, Inc. and its subsidiaries are covered
by U.S. and foreign patents and/or pending patents.

TEKTRONIX, TEK, SCOPE-MOBILE, and ~ are regis-
tered trademarks of Tektronix, Inc. TELEQUIPMENT is a
registered trademark of Tektronix U.K. Limited.

There is no implied warranty of fitness for a particular pur-
pose. Tektronix, Inc. is not liable for consequential
damages.

Specification and price change privileges are reserved.

Printed in U.S.A.
8560 Series Hardware Installation




Section 4
INSTALLATION OVERVIEW


Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-1

First-Time Installation (Basic System). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-1

What Is an 8560? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-5
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-5
Hardware .................................................................. 4-5
Main Interconnect Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-6
LS 1-11/23 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-6
LSI-11/73 Processor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-6
System Memory .......................................................... 4-6
Mass Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-7
MSC Controller Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-7
Utility Board .............................................................. 4-7
I/O Processor ......................................... ~ ................... 4-7
Communications Adapters ................................................... 4-8



ILLUSTRATIONS
Fig.
No. Page
4-1 First-time installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4-2




4-i
8560 Series Hardware Installation




OPERATORS SAFETY SUMMARY
The general safety information in this part of the summary is SAFETY PRECAUTIONS
for both operating and serviCing personnel. Specific
warnings and cautions will be found throughout the manual Grounding the Product
where they apply, but may not appear in this summary. This product is grounded through the grounding conductor
in the power cord. To avoid electrical shock, plug the power
cord into a properly wired receptacle before connecting to
the equipment's power input terminals. A protective ground
TERMS connection by way of the grounding conductor in the power
cord is essential for safe operation.
In This Manual
CAUTION statements identify conditions or practices that Use the Proper Power Cord
could result in damage to the equipment or other property.