Text preview for : 4674-2,0.pdf part of
| Home
Test Fixtures
Device Compatibility 3323A 3327 8006 8007 8008 8009
Sheet Resistance I I
Volume Resistance I I
Axial Devices I I
Chip Devices I
T0 18 Packages 4-Lead I
T0 5 Packages 4-Lead I
8-Lead I
Dual In-Line Packages 24-Lead I
28-Lead I
48-Lead I
Prototyping Board I
Instrument Compatibility 3323A 3327 8006 8007 8008 8009
Characterization Systems 4200-SCS I I
Model 3323A Direct Test Fixture
DMMs 197A I I
2000, 2001, 2002, 2010 I I The Model 3323A is designed for component
Nanovoltmeters 2182 I measurement by directly inserting the component
Test fixtures
Sources 213 I I into the fixture. It can accommodate axial-lead
220 I I components or radial-lead components without
224 I I bending the component leads.
228A I I
230 I I For use with: LCZ Meters.
263 I I
SMUs 236 I I I
237 I I I
238 I I I
Picoammeters 428 I I I
485 I I I
486 I I I
487 I I I
C-V Meters 590 I I
595 I I
Electrometers 6514 I I I
6517A I I I I
Switching Matrix
707A, 708A, 7072, 7172, 7174A I I
LCZ Meters 3321 I I Model 3327 Chip Component Test Fixture
3322 I I
3330 I I
The Model 3327 Chip Component Test Fixture pro-
vides a convenient method for testing the imped-
All test fixtures are available with an Extended Warranty. ance of chip (i.e., SMD) components. The spring-
loaded plunger provides consistent contact pres-
sure for measuring low impedance devices and low
predictable stray capacitance for measuring low
capacitive devices.
For use with: LCZ Meters.
INSTRUMENT ACCESSORIES
1.888.KEITHLEY (U.S. only)
www.keithley.com
A G R E A T E R M E A S U R E O F C O N F I D E N C E
Test Fixtures
on Dual In-line Packages (DIPs) of 0.3 or 0.6 inch
centers and up to 48 pins with the 24- or 48-pin
socket. The prototyping board can be installed on
the front panel for customized testing of packages
with up to 72 pins.
Accuracy is maintained to the DUT with isolation
of more than 1T. Offset current for the 8007 is
less than 1pA, while maximum signal voltage is
200V with 1A peak current. A hinged cover pro-
vides light-tight and shielded measurements. 72
ferrite beads are also included for custom applica-
tions when DC tests are performed on active
devices and some decoupling is required.
Model 8006 Component Test Fixture Supplied with interlock cable, phototyping Model 8009 Resistivity Chamber
The Model 8006 Component Test Fixture board, and two input cables (each terminated
was designed specifically for making sensitive mea- with twelve 3-slot triax plugs). The Model 8009 is a guarded test fixture for mea-
surements on standard package devices with mini- suring volume and surface resistivities. It assures
Test fixtures
mal setup time. Individual components may be good electrostatic shielding and high insulation
connected to one of eight device sockets, includ- resistance up to 1100V. The 8009 is designed for
ing axial, 4-, 8-, 10-, and 12-lead T0, and 28-pin safe operation with the 6517A. Opening the lid of
DIPs. Instrumentation can be easily integrated the 8009 automatically turns off the 6517A voltage
through the 3-lug triax, BNC, or binding post con- source. The 8009 accommodates sheet samples
nectors on the rear panel. from 64mm to 102mm (21/2 to 4 in) in diameter
and up to 3.2mm (1/8 in) thick. It maintains good
Signals from the test instruments are accessible at sample contact with uniform pressure (from 6 to
the test fixture's front panel. Mini jumper cables 10 lbs depending on thickness) on smooth parallel
are provided to connect the signal to the appropri- samples.
ate device socket, which is also located on the
front panel. This unique patch-board design allows With the front panel switch on the 8009, toggle
for maximum versatility and the fastest possible between volume and surface resistivity, with the
setup times. 6517A configured to calculate and display the
Model 8008 Resistivity Chamber appropriate result automatically. The 8009 permits
The 8006 Test Fixture maintains accuracy through- direct measurement of volume resistivity up to
out the test circuit with greater than 100T The 8008 Resistivity Chamber is a guarded 1018-cm (on samples 0.1cm thick) and surface
(1014) path isolation, 4-wire connections, guard- test fixture for measuring volume and surface resis- resistivity up to 1017/square, in accordance with
ed jumpers, gold contacts and interconnects, and tivities. It assures good electrostatic shielding and ASTM procedures.
less than 100fA offset current. A hinged lid covers high insulation resistance up to 1100V.
Supplied with necessary cables to use with
the component panel to provide a light-tight and
The 8008 accommodates sheet samples 64 6517A, including Model 8607 Safety HV Dual
shielded measurement.
to 102mm (21/2 to 4 in) in diameter and up to Test Leads
3.2mm (1/8 in) thick. It maintains good sample con-
ENVIRONMENTAL LIMITS: Operating: