Text preview for : Konka_26CS66_KL32CS66_KL37CS66_42CS66_KL32CS31_KL37CS31_KL42CS31_LCD_TV_Service_Manual.pdf part of
| Home
LCD TV SERVICE MANUAL
Modle list
KL26CS66,KL32CS66,KL37CS66
KL42CS66,KL32CS31,KL37CS31
KL42CS31
KONKA GROUP CO,LTD.
Digital Flat Display Division
IMPORTANT SERVICE SAFETY INFORMATION
Operating the receiver outside of its cabinet or with its back removed involves a shock hazard. Work on these
models should only be performed by those who are thoroughly familiar with precautions necessary when working on
high voltage equipment.
Exercise care when servicing this chassis with power applied. if carelessly contacted, can cause serious shock or
result in damage to the chassis. Maintain interconnecting ground lead connections between chassis, escutcheon, picture
tube dag and tuner when operating chassis.
When it is necessary to make measurements or tests with AC power applied to the receiver chassis, an Isolation
Transformer must be used as a safety precaution and to prevent possible damage to transistors. The Isolation
Transformer should be connected between the TV line cord plug and the AC power outlet.
It is important to maintain specified values of all components and anywhere else in the received that could cause
a rise in operating supply voltages. No changes should be made to the original design of the receiver.
Components shown in the shaded areas on the schematic diagram and/or identified by in the replacement parts
list should be replaced only with exact factory recommended replacement parts. The use of unauthorized substitute
parts man creates may create shock, fire, or other hazards.
Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis
and other metal parts in the receiver.
2. Replace all protective devices such as non-metallic control knobs, insulating fish papers, cabinet backs, adjustment
and compartment covers of shields, isolation resistor-capacitor networks, mechanical insulators etc.
3. To be sure that not shock hazard exists, a check for the presence of leakage current should be made at each exposed
metal part having a return path to the chassis (antenna, cabinet metal, screw heads knobs and/or shafts, escutcheon,
etc.) in the following manner.
Plug the AC line cord directly into a 110V/220V/240V, AC receptacle. (Do not use an Isolation Transformer
during these checks.) All checks must be repeated with the AC line cord plug connection reversed. (If necessary, a
non-polarized adapter plug must be used only for the purpose of completing these checks.)
PLEASE READ BEFORE ATTEMPTING SERVICE
1. Use an Isolation Transformer when performing any service on this chassis.
2. Never disconnect any leads while receiver is in operation.
3. Disconnect all power before attempting any repairs.
4. Do not short any position of the circuit while the power is on.
5. For safety reasons, replace components any with identical replacement parts (SEE PARTS LIST).
6. Before alignment, warm up the TV for at least 30 minutes.
7. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the
wire back in its original position.
8. Inferior silicon grease can damage IC's and transistors. When replacing IC's and transistors, use only
specified silicon grease. Remove all old silicon when applying new silicon.
9. Before removing the anode cap, discharge eletricity because it contains high voltage.
A. SPECIFICATION
System : PAL:I , B/G , D/K; SECAM: D/K , B/G
Audio Output Power :
Size 26 32 37 40 42
Power(W) 4W*2 5 W*2 5W*2 5 W*2 5 W*2
Antenna Impedance : 75
Power Consumption : 340WMax
Size 26 32 37 42
Power
160 180 200 270
Consumption(W)
Power Supply : ~110240V, 50/60Hz
Item Port List
1 RF Cable
2 Headphone Audio Output
3 S-Video Input
4 AV Input
5 AV Output
6 YPbPr
7 Component Audio Input
9 VGA/RGB
10 VGA Audio Input
11 HDMI Input
B. ADJUSTMENT MANUAL
TEST NOTE
1. Please follow the pointed test steps and choose the right test equipment to conduct adjustment,
otherwise good effect of Unit could not be obtained. The unit should be warmed up for 30 minutes
before adjustment and every parameter should be adjusted repeatedly till the optimum value
obtained, the pointed voltage value should be ensured during test to get satisfied test result.
2. Test environment
1) Temperature : 15