Text preview for : 058aadj.pdf part of LG 058aadj LG TV CI-25H40 CI-25H40 058aadj.pdf



Back to : 058aadj.pdf | Home

ADJUSTMENT
Y Safety Precautions
1. It is safe to adjust after using insulating transformer
between the power supply line and chassis input to PAL/SECAM-BG
SYSTEM PAL-BG/DK PAL-I
prevent the risk of electric shock and protect the SECAM-LL'
instrument.
2. Never disconnect leads while the TV receiver is on. TUNER 6700VPF002A 6700VPF002B 6700VPF002B
3. Don't short any portion of circuits while power is on.
AGC Voltage 2.3 ! 0.1V 2.3 ! 0.1V 2.1 ! 0.1V
4. The adjustment must be done by the correct appliances.
But this is changeable in view of productivity. NOTE: AGC must be adjusted when the tuner was changed.
5. Unless otherwise noted, set the line voltage to
230Vac!10%, 50Hz. : Screen Voltage Adjustment

Y Test Equipment required
1. Multimeter (volt meter)
2. Oscilloscope Test Point : RK (Red Cathode of CPT Board)
Adjust : Screen Control of FBT


: RF AGC (Automatic Gain Control) Adjustment 1) Tune the TV set to receive a digital pattern.
2) Press PSM (RED) button on remote controller. (standard
Test Point : AGC TP (J3) picture)
Adjust : Remote Control 3) Connect the probe of oscilloscope to the RK (Red
Cathode) of CPT Board.
4) Adjust Screen Volume of FBT so that the waveform is the
The RF AGC was aligned at the time of manufacture for same as below figure.
optimum performance over a wide range conditions.
Readjustment of RF AGC should not be necessary unless
Horizontal
unusual local conditions exist, such as ; FlyBack Time
Black level
1) Channel interference in a CATV system. 160Vp-p
2) Picture bending and/or color beats, which are unusually
due to excessive RF signal input when the receiver is too
close to a transmitting tower or when the receiver is White level
connected to an antenna distribution system where the RF 1H-LINE GND for dc
signal has been amplified. In this case, the input signal
should be attenuated (with pad or filter) to a satisfactory The waveform of RK(Red Cathode) of CPT Board
level.
3) Picture noise caused by "broadcast noise" or weak signal.
If the broadcast is "clean" and the RF signal is at least
1mV (60dBu), the picture will be noise free in any area. : Focus Adjustment

NOTE: This adjustment should be performed after warming
up for 10 minutes.
Adjustment
1. Connect RF signal (65dB) and turn on the TV. Test Point : Observing Display
2. Press OK buttons on TV set and Remote Controller at the Adjust : Focus control of FBT
same time to get into SVC mode.
3. Press Channel UP/DOWN button on the Remote Controller
1) Tune the TV set to receive an inactive channel station.
several times to find AGC.
2) Adjust the Focus control of FBT for best overall focus.
4. Press Volume UP/DOWN button until the AGC Voltage is
the same as the Table below.
5. Press OK(Y) button to memorize the data.




- 1 -
: Deflection Data Adjustment (Line SVC-1)

NOTE: To enter SVC mode, press "OK" buttons on both TV set
and the Remote control at the same time.

1. Preparation for Deflection Adjustment
1) At SVC mode, press the Yellow colored button.
If the Remote Controller doesn't have the Yellow button, you
should use a Service Remote Control (105-201G) and press
SVC button.
And then, deflection data adjustment OSD (SVC1 mode) will
be displayed.
2) Press Channel UP/DOWN button for desirous function a
Adjustment.
3) Press Volume UP/DOWN button to adjust the data.
b

2. Deflection Adjustment Procedure


VL (Vertical Linearity)
Adjust so that the boundary line between upper and lower 3. Deflection Initial Setup Data
half is in accord with geometric horizontal center of the CPT.
PAL 50Hz NTSC 60Hz
Item
VA (Vertical Amplitude) Normal Wide Zoom Normal Wide Zoom
Adjust so that the circle of a digital circle pattern may be
located within the effective screen of the CPT. VL 33 30 28 28 29 27

VA 31 33 30 37 33 33
SC (Vertical "S" Correction)
Adjust so that all distance between each horizontal lines are SC 18 18 18 18 18 18
to be the same.
VS 29 41 40 40 41 43
VS (Vertical Shift) HS 27 29 29 35 35 35
Adjust so that the horizontal center line of a digital circle
pattern is in accord with geometric horizontal center of the EW 50 46 55 49 47 57
CPT.
EP 42 48 48 48 48 47
HS (Horizontal Shift) EC 26 26 26 26 30 39
Adjust so that the vertical center line of a digital circle
pattern is in accord with geometric vertical center of the ET 28 29 29 35 30 29
CPT.
VZ 31 0 45 29 0 43
EW (Horizontal Width)
Adjust to that a digital circle pattern looks like exact circle.

EP (East-west Parabolar)
Adjust so that middle portion of the outermost left and right : White Balance Adjustment.(LINE SVC-0)
vertical line looks like parallel with vertical lines of the CPT.
NOTE : This adjustment should be performed after screen voltage
EC (East-west Coner) adjustment.
Adjust so that the vertical line at every 4 corners of the
screen looks like parallel with the vertical lines of the CPT. 1) Tune the TV set to receive an 100% white pattern.
2) Press OK(Y) buttons on TV set and remote controller at the
ET (East-west Trapezium) same time to get into SVC mode.
Adjust to make the length of top horizontal line same with it 3) Press PSM(RED) button on remote controller. (Standard
of the bottom horizontal line. picture)
4) Press Channel UP/DOWN button for desirous function
VZ (Zoom Mode, Vertical Height) adjustment.
Select the zoom mode with ARC button and adjust the data 5) Adjust VOL+ or VOL- button for GG:31.
until the lines a and b of figure are 5~10mm from the top 6) Adjust VOL+ or VOL-button in each status of "Rg--"/"Bg--" for
and bottom of CPT and 3~5mm from each sides of CPT. X=293!8, Y=295!8 with color analyzer.
7) Press OK(Y) button to memorize the adjustment data.




- 2 -
ITEM DATA Table 2. OPTION 2. Function & DATA
AGC 20 (*)
ITEM DATA
RG 41 (*)
GAI 1
GG 31 (*)
5LANG 0
BG 29 (*)
OPTION Data 2
CDL 6

Y-Del 10

(15, UK)

DS 1

DSA 1

NOTE: "(*)" marked items must be adjusted.




: LINE SVC-2

ITEM DATA

FP 30

NP 118

SP 23

S1 VOL 75

S2 VOL 75




: OPTION Adjustment (SVC MODE:OPTION-1,
OPTION-2)

NOTE: When the EEPROM has been replaced, the Option data
should be restored as the function of individual system
and specification.

1) Press OK buttons on both TV set and Remote Controller at
the same time to get into SVC mode.
2) Press the Yellow button several times to find OPTION-1 or
OPTION-2.
3) Input the correspond OPTION data referring to Table below
with the numeric buttons 0~9.




Table 1. OPTION 1. Function & DATA

ITEM DATA

SYSTEM B+L(FRANCE), I(UK), B+D(GERMANY, NORTH/EAST EUROPE, etc.)

TOP ON(GERMANY, SWISS, AUSTRIA), OFF(FRANCE, UK, NORTH/EAST EUROPE, etc.)

OPTION Data 8(FRANCE), 11(UK), 13(GERMANY), 9(NORTH/EAST EUROPE, etc.)




- 3 -
: CH(EEPROM) Data
Germany

No. CH. FREQ. Pattern Sound
1 EU-05 175.25 Digital ST
2 EU-04 62.25 Digital DUAL
3 EU-31 551.25
4 EU-51 711.25
5 EU-25 503.25 Color BAR N/ST, TXT
6 EU-50 703.25 Digital ST
7 EU-52 719.25 Color BAR N/ST, TXT
9 R-05 93.25 Digital SECAM D/K
10 R-34 575.25 Digital SECAM D/K


France

No. CH. FREQ. Pattern Sound
1 SL-45 663.25
2 SL-B 55.75 Cross Hatch TXT
3 SL-04 200.00
4 EU-05 175.25 Digital ST
5 EU-04 62.25 Digital DUAL
6 EU-31 551.25
7 EU-51 711.25
8 SL-23 487.25 Color BAR
9 SL-03 192.00 Digital N/DUAL
10 EU-52 719.25 Color BAR N/ST, TXT


UK

No. CH. FREQ. Pattern Sound
1 PI-41 631.25 Digital N/DUAL
2 PI-21 471.25
3 PI-69 855.25
4 PI-63 807.25 Digital N/DUAL


North/East Europe etc.

No. CH. FREQ. Pattern Sound
1 EU-05 175.25 Digital ST
2 EU-04 62.25 Digital DUAL
3 EU-31 551.25
4 EU-51 711.25
5 EU-25 503.25 Color BAR N/ST, TXT
6 EU-50 703.25 Digital ST
7 EU-52 719.25 Color BAR N/ST, TXT
8 R-05 93.25 Digital SECAM D/K
9 R-34 575.25 Digital SECAM D/K




- 4 -