| Make | Model | Problem | Solution | Date |
| | | |
| Found: 8441
|
| Aiko | CT20 | Int dead | dry joint R233 | 14-09-04 |
| Aiko | CT20 | Int field - height | FOP tr Q303 2SB546A faulty - used TIP42C in lieu | 14-09-04 |
|
|
| Aiwa | C202KER | Field collapse | Fusible link 1500 marked as jumper lead from loptx to reg via D6813 | 14-09-04 |
| Aiwa | SE211K | St/by only | R617 high (replace with 390K 1/4W) - located behind LOPTX.This causes the micro-controller to shut the set down and store this condition in the EEPROM. You can either replace the EEPROM with the correct one from Aiwa (which then requires setting up with a special handset), or use an EEPROM programmer to reset the values. There are two values that require resetting:
$0139 should be $00 ($2F when faulty)
$013C should be $00 ($33 when faulty)
| 14-09-04 |
| Aiwa | TVC211 | St/by only | Replace EEPROM & R617 - the cause - which goes hi res | 14-09-04 |
| Aiwa | TVSE211 | No vid/raster with sound - no/poor OSD | IC303 (OSD Sw) pt no Aiwa87A21167010 | 14-09-04 |
| Aiwa | VX9142K | Dead | R516 270k in psu o/c | 14-09-04 |
| Aiwa | VXD1420 | Pin code removal | Enter wrong no 3 x, then press Vol- on set & "7" on R/C for 5 secs when "protected" appears | 14-09-04 |
| Aiwa | VXD2120K | Pin code resetting when lost | unplug set for 1 hour plus. reduce volume to minimum. simultaneuously press Volume down on unit and "7" to reset pin code and customer ID | 14-09-04 |
| Aiwa | VXG142 | No raster - OSD OK | Q1029 near tuner | 14-09-04 |
| Aiwa | VXG142K | Dead - no st/by | R516 270K, IC501 TDA4605-3, Q500 2SK2397-01MR | 14-09-04 |
| Aiwa | VXG142K | Dead - no stby | R516 270k, IC501 TDA4605-3, Q500 2SK2397 | 14-09-04 |
| Aiwa | VXG142K | Dead with st/by led lit - accepts a tape but no functs | ICP506 1A CP on tv pcb o/c | 14-09-04 |
| Aiwa | VXG142K | Dead with fast tripping aft power cut | C513/C538 1m 160v in psu hi esr | 14-09-04 |
| Aiwa | VXG142K | No pic or vcr mechs - osd & sound ok | Replacing the faulty switching transistor Q511 [2SB926] which supplies the chroma +9V cured both faults. It is situated at the back LHS of the VCR board. | 14-09-04 |
| Aiwa | VXG142K | No sigs | Q1029 (2SC926) at rear of vcr pcb s/c - used a BD234 | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Dead | Ht ok at 120v - ICP1 o/c | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Dead | STK7348 s/c pins 3 & 7, also R103 1R5 3W o/c, R104 27R 3w, R105 1k 1/2w & C90 1µ 50v | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Dead - no line drive | D7 9v1 zener & C105 330µ 16v both s/c | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Failure of IC STK7348 in tv psu | Replace:R102. 33ohmlW Part No S5 34A 330 000 R104 27ohm 3W Part No Sl 330 703 000(6.25UKP) RlOl 33ohm7W Part No Sl 330 862 000(8.37UKP) Also please check and if necessary replace:R103(3.76UKP) R105 Replace as required.
R109(4.00UKP) NOTE: Do not replace IC on its own.<< | 14-09-04 |
| Aiwa | VXT1000Mk2 | Dead | STK7348 psu chip & C88 0.0033pf 2kv | 14-09-04 |
| Aiwa | VXT1000Mk2 | Dead TV sect - vcr sect ok | C88 0.0033µ 1kv burnt; STK7348 psu chip s/c; R109 3R9 7w o/c | 14-09-04 |
|
|
| Aiwa | VXT1000Mk2 | No pic sound ok | C88 3n3 1kv burnt | 14-09-04 |
| Aiwa | VXT1420k | Dead | Start up Res R502 1M & R503 820k | 14-09-04 |
| Aiwa | VXT1420K | St/by only | LOPTr leaky | 14-09-04 |
| Akai | 2185 | Won't go into st/by | CHECK SUPPLY TO PIN 1 OPTOCOUPLER - R572 ( 470ohm ) | 14-09-04 |
| Akai | 2870 | TEXT ODDITY | REPROGRAM MICRO.PRESS TEXT ON REM , S ON TV , THEN TEXT AGAIN | 14-09-04 |
| Akai | Comp D2 | Dead | D/J on on off switch or On off switch burnt | 14-09-04 |
| Akai | CT-T21N32S | I have an Akai CT-T21N32S which will not fire up, the red LED is illuminated on the front but nothing else happens, I have tested dozens of components but to no avail, the block diagram in the service manual I have is unreadable which is quite upsetting a | cure: replace eeprom IC602 ref
| 23-06-05 |
| Akai | CT20K2PA | Dark pic - increasing sub brill resulted in field coll | R436 120k o/c | 14-09-04 |