| Make | Model | Problem | Solution | Date |
| | | |
| Found: 24
|
| B & O | 3600 | Blue Picture | 16R1 ( 1.5Mohm ) | 14-09-04 |
| B & O | 3600 | No E-W Correction | 6D5 ( BY299 ) | 14-09-04 |
| B & O | 3600 | No Picture - Failureof Line o/p Transitor | 0C1 ( 9.1nf ) | 14-09-04 |
| Grundig | CUC 6360 / CUC 6361/ CUC 6365 | Intermittent no picture, it would fade out with the width getting smaller.
HT 150volts was down to 100volts. | C672 100 MFD @ 250VW | 14-09-04 |
| Grundig | CUC 6360 / CUC 6361/ CUC 6365 | No picture, but HT / EHT all ok, picture was blanked out. | CT5066 BC858. This is a s.m. device on the video processing pcb. It is on p22 of ic 5040. | 14-09-04 |
| Grundig | CUC3600 | breathes with brill | Tripler/focus unit u/s | 14-09-04 |
| Grundig | CUC3600 | Broad white vert bar & SECAM light on | BU508A LOPTr overheating. TDA8140 chip faulty - driving it at twice freq | 14-09-04 |
| Grundig | CUC3600 | No pic - dim vert band | Check loptr base wfm - if low or twice normal speed check C507 100µ & IC550 TDA8140 | 14-09-04 |
| Grundig | CUC3600 | No pic - pic blanked | Check supplies & sandcastle pulse. Brill & contrast cont volts at pins 2 & 16 TDA8442 IC350 - if low & won't increase TDA8442 is sus | 14-09-04 |
| Grundig | CUC3600 | No picture - EHT Ok. | If pins 2 & 16 do not increase if brit/cont is adj IC350 TDA8442. | 14-09-04 |
|
|
| Grundig | CUC3600 | NO PICTURE JUST DIM VERTICAL BAND ON SCREEN | C507 100uF OR IC550 TDA8140 | 14-09-04 |
| Grundig | CUC5350 CUC5360 | "P1" DISPLAYED AFTER PROCESSOR CHANGED | R836 FROM 10K TO 22K ( OLD SDA 20562 A 006 NEW SDA 20562 A 506 Grundig 8305-157-580 ) | 14-09-04 |
| Grundig | CUC5360 | No NICAM sound - whistle on mono sound | MSP2400 chip in IF module | 14-09-04 |
| Grundig | CUC5360 | Col int | Replace 4.43Mhz red trimmer | 14-09-04 |
| Grundig | CUC5360 | int tuner | check for dry joints on xtal | 14-09-04 |
| Grundig | CUC5360 | No vid via scart skt | Sw carried out in tuner/IF chip. Check CT2512/3/4/7 sm types BC848/858 | 14-09-04 |
| Grundig | CUC5360 | Store ,tuning , analogue controls inoperative | Check memory Ics IC847/8 also bad earths which could be cause of Ics going faulty | 14-09-04 |
| Grundig | CUC6360 | E/W dist & lack of width | R508 5R6 fusible middle rear of main pcb | 14-09-04 |
| Grundig | CUC6360 | No sound | MSP3410 chip | 14-09-04 |
| grundig | CUC6360 | No Sound | Try to unplug the green connector going to the main swich (startup sliding switch),if sound comes on change main switch and clean the switch board from dust. | 08-12-06 |
| NordMende | 3602 F8 | Blue smearing - like tube down. | | 14-09-04 |
| NordMende | 3602 F8 | No luma & red flyback lines. | IC TDA1170 frame IC. | 14-09-04 |
| Samsung | TVP33601 | Field foldover at top | Check R409 0R22, R303 10R ?w from 46v supply | 14-09-04 |
| Seleco | SM360.1UK | Slow start up from small to normal size pic | C423 47µ 250v (+142v HT res cap) | 14-09-04 |