datasheet,schematic,electronic components, service manual,repairs,tv,monitor,service menu,pcb design
Schematics 4 Free
Service manuals, schematics, documentation, programs, electronics, hobby ....


registersend pass
Bulgarian - schematics repairs service manuals SearchBrowseUploadWanted

Now downloading free:PASSLAB Pass-Labs Aleph-4 Rev.0 sm

PASSLAB Pass-Labs Aleph-4 Rev.0 sm free download

Audio equipment,digital audio, home audio, professional audio systems service manuals and repair information

File information:
File name:Pass-Labs_Aleph-4_Rev.0_sm.pdf
[preview Pass-Labs Aleph-4 Rev.0 sm]
Size:816 kB
Extension:pdf
Mfg:PASSLAB
Model:Pass-Labs Aleph-4 Rev.0 sm 🔎
Original:Pass-Labs Aleph-4 Rev.0 sm 🔎
Descr: . Rare and Ancient Equipment PASSLAB Audio Pass-Labs_Aleph-4_Rev.0_sm.pdf
Group:Electronics > Consumer electronics > Audio
Uploaded:09-08-2020
User:Anonymous
Multipart:No multipart

Information about the files in archive:
Decompress result:OK
Extracted files:1
File name Pass-Labs_Aleph-4_Rev.0_sm.pdf

Pass Laboratories Aleph 4 Service Manual Rev 0 8/18/1997 Aleph 4 Service Manual. The Aleph 4 is a stereo 100 watt audio power amplifier which operates in single-ended class A mode. The Aleph 4 has only two gain stages which are biased by current sources. Because of the inherent simplicity of the circuit, it is easy to understand and repair. There are no adjustments. Figure 1 shows the simplified schematic of the amplifier. Two p channel Mosfets form an input differential pair biased by a current source operating at about 20 ma. The drain of the input Mosfet is attached to the gate of an n channel power Mosfet which forms the active output stage. It is biased by a current source at slightly greater than 3 amps. The voltage rails of the supply are at 48 volts, and each channel draws approximately 250 watts. Fig. 2 and 3 show the actual schematic for the amplifier. F1 is a slow blow fuse, set at 8 amps for 100-120 volt operation, and 4 amps for 220- 240 volt operation. S1 is the power switch, which has two sets of 25 amp contacts wired in parallel. T1 is a thermostatic switch rated at 75 degrees Centigrade. It is mounted to the rear heat sink. TH2 is a power thermistor used to connect the circuit and chassis ground to the AC outlet ground. It will normally operate at 5 ohms, suppressing ground loops in the system, but will drop to a low impedance if significant current is passed through it. TH1 and TH3 are power thermistors (Keystone CL-60) which are used to suppress inrush current. The power transformer drives a high current bridge and 100,000 uF of capacitance to form a plus and minus 48 volt supply. Referring to the channel itself, Q1A1 and Q1A2 form the differential input pair of Mosfets. They are biased by the current source formed by Q1A5. Q1A5 is biased to about 20 ma by the reference Zener diode Z9 which sets about 5 volts across R11. Z1, 2, 7 and 8 protect the input from static spikes. R5, R14-18 and R53 form the input networks and feedback loops. The output of the differential input pair drives the gates of output devices Q18-29. These parallel devices are matched gate to source voltages as close as .01 volts, however variations as high as .1 volts will not impede operation. The voltage across R24 shows the drive voltage for the output stage, and it should have 4-5 volts across it. The output of the amplifier is taken from the drains of Q18-20. Q18-20 are provided a bias current by the current source circuitry of Q6-8, also a matched set of n channel Mosfets. Q6-8 are set at 3 amps DC by the network consisting of Q3 and the components surrounding it. Q3 is biased by R25 and R27 in series. A capacitor C8 is used to reduce supply noise. R28 serves to sense the current running through Q6, and feeds that to the base of Q3, forming a loop that holds the output current at 3 amps. The pn junction drop of Q3 forms the reference voltage for the system. R26 is a fixed resistor which trims the DC current value. R29 and C9

>> View document online <<



>> Download document << eServiceInfo Context Help



Was this file useful ? Share Your thoughts with the other users.

User ratings and reviews for this file:

DateUserRatingComment

Average rating for this file: 0.00 ( from 0 votes)


Similar Service Manuals :
PASSLAB aleph 5 - PASSLAB a5serv0 - PASSLAB Pass-Labs Aleph-P Rev.1.7 sm - PASSLAB Pass-Labs Aleph-ONO Rev.0,1,2,3 sm - PASSLAB Pass-Labs Aleph-3 Rev.0 sm - PASSLAB Pass-Labs Aleph-1.2 Rev.0 sm - PASSLAB Pass-Labs Aleph-2 Rev.0 sm -
 FB -  Links -  Info / Contacts -  Forum -   Last SM download : Marantz CD65II

script execution: 0.02 s