1401ps.pdf part of 1401ps.rar, schema tv text manual preview

Text preview for : 1401ps.pdf part of schema tv

Back to : 1401ps.rar | Home

TOSHIBA STORAGE DEVICE DIVISION
SD-M1401 DVD-ROM DRIVE PRODUCT SPECIFICATION

May 2000 REV. 1.0

Specifications are subject to change without notice

DOCUMENT NUMBER 12369

Notice
1.This product has no over-current protection circuit. System should have appropriate over-current protection. Toshiba Corporation makes no warranty of damages caused by no over-current protection. 2.This has a little possibility of errors. To prevent damages and injury caused by the above, careful consideration for the safety and integrity should be taken in the system design. Do not use this product in a system that may cause hazard to human being or material loss caused by the failure, loss of data and/or errors of this product. 3.Do not disassemble or modify this product. Or, reliability, safety and performance can not be guaranteed. 4.Turn off the system power before mounting/removing this product. Or, it may cause failure or damage. 5.Because the DC power socket of this product allows insertion of only one side direction, ascertain direction carefully to insert the plug. 6.To build this product in an equipment, handle it only in electrostatically safe environment. Do not touch connecting terminals directly. Or, the product may be damaged by electrostatic energy. 7. This product can playback discs based on the formats described in item 3.1.(1). Do not load a disc which is not conformed with those formats such as a shaped disc or a disc with its weight unbalanced excessively. A very high speed rotation is carried out inside the product, so abnormal vibration and malfunction may occur if disc described above is loaded. 8. When a disc cannot be ejected because of some troubles, etc., turn off the power for the unit and eject the disc using the emergency eject mechanism after passing more than 1 minute. When the emergency eject is carried out while the power is on or immediately after the power off, the disc may be eject in a rotating status. We do not assure if the disc is damaged by this.

9. When you close the tray, power must not be turned off. If the tray is pushed in with the hand during power off, a breakdown may occur because the mechanism in the product is not in the transit state during power off.

10. This product comes under the regulations of TWA (The Wassenaar Arrangement on Export Controls for Conventional Arms and Dual Use Goods and Technologies). When exporting the product, an export permission according to the regulations of your country will be required.

SD-M1401 Rev.1.0

11. As for mounting bracket to incorporate this product into an equipment, (1) When this product is incorporated into an equipment by using the mounting screw holes in the right and left side planes, the clearance between this product and the mounting bracket is too wide; (2) When this product is incorporated into an equipment by using the mounting screw hole in the bottom, the surface of the mounting bracket is contorted. If you use such mounting bracket as the above, this product will become deformed, which may cause operation failure. Therefore, it is necessary to take account of the mounting bracket which has the tolerances shown in Fig.1 or whose structure cannot cause this product to deform, as shown in Fig.2
146+/-0.3

less than plane 0.5

+ 146.3- 0.2 0

Select screws, the length of which threaded onto the product is within 3 +/- 0.5 mm

Fig.1
When a large amount space is left, insert spacers, etc. to adjust the space less than 0.5 mm between the product and mounting bracket.

this product

this product

before the fixing mounting bracket

after the fixing

Fig.2

SD-M1401 Rev.1.0

12.When mounting the product on other instrument, take care that the external surface temperature of the product does not exceed 55 °C. 13. In the instruction manual of your product, statement described in "Safety Instruction Manual "attached to this product, the statement of item 2,7 and 9 above, and other required statements should be mentioned for thorough understanding by the users.

SD-M1401 Rev.1.0

Contents
1. Introduction ---------------------------------------------------------------------------------------------------------------------- 1 2. Features -------------------------------------------------------------------------------------------------------------------------- 3 3. Specifications ------------------------------------------------------------------------------------------------------------------ 4 3.1. Performance ------------------------------------------------------------------------------------------------------------ 4 3.2. Environmental Conditions ---------------------------------------------------------------------------------------- 6 3.2.1. Temperature and Humidity ---------------------------------------------------------------------------------- 6 3.2.2. Dust and Dirt ------------------------------------------------------------------------------------------------------ 6 3.2.3. Vibration ----------------------------------------------------------------------------------------------------------- 6 3.2.4. Atmospheric Pressure and Altitude -------------------------------------------------------------------- 6 3.2.5. Shock --------------------------------------------------------------------------------------------------------------- 6 3.3. Installation Conditions --------------------------------------------------------------------------------------------- 7 3.4. Dimensions and Mass --------------------------------------------------------------------------------------------- 7 3.5. Reliabilities ------------------------------------------------------------------------------------------------------------- 9 3.5.1. Error Rate ---------------------------------------------------------------------------------------------------------- 9 3.5.2. MTBF ---------------------------------------------------------------------------------------------------------------- 9 3.5.3. MTTR ---------------------------------------------------------------------------------------------------------------- 9 3.5.4. Drive Life ----------------------------------------------------------------------------------------------------------- 9 4. Configurations ----------------------------------------------------------------------------------------------------------------- 9 4.1. Electrical Circuits ------------------------------------------------------------------------------------------------------ 9 4.2. Optical Pickup --------------------------------------------------------------------------------------------------------- 9 4.3. Spindle Motor ---------------------------------------------------------------------------------------------------------- 9 4.4. Feed Motor -------------------------------------------------------------------------------------------------------------- 9 4.5. Tray Load/Eject Motor ---------------------------------------------------------------------------------------------- 9 5. Functions ------------------------------------------------------------------------------------------------------------------------11 5.1. Disc Data Configurations ------------------------------------------------------------------------------------------11 5.1. 1. DVD-ROM Data Configurations ---------------------------------------------------------------------------11 5.1. 2.CD-ROM Data Configurations ------------------------------------------------------------------------------11 5.2. Power ON/OFF Timing --------------------------------------------------------------------------------------------12 6. Interfaces ------------------------------------------------------------------------------------------------------------------------13 6.1. Signal Line ---------------------------------------------------------------------------------------------------------------13 6.1.1. Signal Line Summary -----------------------------------------------------------------------------------------13 6.1.2. Receiver and Drivers ---------------------------------------------------------------------------------------- 13 6.1.3. Connector ------------------------------------------------------------------------------------------------------- 13 7. Power Requirements ----------------------------------------------------------------------------------------------------- 19 7.1. Source Voltage ------------------------------------------------------------------------------------------------------ 19 7.1.1. Spike -------------------------------------------------------------------------------------------------------------- 19 7.1.2. Ripple ----------------------------------------------------------------------------------------------------------- 19

SD-M1401 Rev.1.0

7.2. Current Drain -------------------------------------------------------------------------------------------------------19 7.2.1. Sleep -------------------------------------------------------------------------------------------------------------- 19 7.2.2. Standby -------------------------------------------------------------------------------------------------------- 19 7.2.3.Continuous ----------------------------------------------------------------------------------------------------- 19 7.2.4. Idle ----------------------------------------------------------------------------------------------------------------- 19 7.2.5.Average ---------------------------------------------------------------------------------------------------------- 19 7.2.6. Maximum --------------------------------------------------------------------------------------------------------- 19 7.2.7. Peak in executing Access -------------------------------------------------------------------------------- 19 7.3. Connector -----------------------------------------------------------------------------------------------------------19 8. Audio ------------------------------------------------------------------------------------------------------------------------ 20 8.1. Line Output ----------------------------------------------------------------------------------------------------------20 8.1.1. Connector ------------------------------------------------------------------------------------------------------ 20 8.2. Audio Modes --------------------------------------------------------------------------------------------------------- 20 9. Jamper Setting/Feature Selector ----------------------------------------------------------------------------------- 21 9.1.SCSI-ID ----------------------------------------------------------------------------------------------------------------- 21 9.2. Parity ------------------------------------------------------------------------------------------------------------------- 21 9.3. Terminator ON/OFF ----------------------------------------------------------------------------------------------- 22 9.4. Host Interface Transfer Block Size -------------------------------------------------------------------------- 22 9.5. Audio Playback ---------------------------------------------------------------------------------------------------- 22 9.6. Terminator Power Supply -------------------------------------------------------------------------------------- 23 9.7. Jumper ----------------------------------------------------------------------------------------------------------------- 23 9.8. Recognition of Setting ------------------------------------------------------------------------------------------- 23 10.Busy Indicator ------------------------------------------------------------------------------------------------------------- 24

11. Connections ------------------------------------------------------------------------------------------------------------- 25 11.1. Power Supply Cable ------------------------------------------------------------------------------------------- 25 11.2. Interface Cable --------------------------------------------------------------------------------------------------- 25 11.3. Audio Cable ------------------------------------------------------------------------------------------------------ 25 12. Emergency Eject ------------------------------------------------------------------------------------------------------ 25 --------------------------------------------------------------------------- 26

13. Safety Standards/Agency Approvals 14. Electrostatic Discharge 15. Accessories 16. Packaging

---------------------------------------------------------------------------------------------- 26

-------------------------------------------------------------------------------------------------------------- 26 ----------------------------------------------------------------------------------------------------------------- 26 -------------------------------------------------------------------------------------- 26

17. CE Declaration of conformity

SD-M1401 Rev.1.0

1. Introduction This document describes TOSHIBA's SD-M1401 DVD-ROM Drive. This drive supports DVD CSS (Contents Scramble Systems) Disc. This drive reads digital data stored on CD-ROM, DVD-ROM and CD audio discs. DVD-ROM disc spec (DVD-ROM Book) defines 120 mm and 80 mm in diameter, single and dual layers as recording layer structure and single and double sides as recording side. Maximum storage capacities are 4.38 GBytes and 15.9 GBytes for single layer/single side and dual layer/double side respectively. (1 GByte=230 Bytes) Due to these high capacity and high data transfer rate of 1352 KBytes/sec, DVD-ROM discs are capable to store high quality and long duration MPEG-2 moving picture data. (1 KByte=210 byte) This drive reads digital data stored on DVD-ROM discs at maximum 10 times faster rotaional speed. This drive reads digital data stored on CD-ROM discs at maximun 40 times faster rotational speed. This drive is a new generation drive with highest performance such as 105 ms(DVD)/85 ms(CD) Access Time. This drive offers long life and durability because the disc is read by a LASER, thereby eliminating physical contact with the disc. This drive supports SCSI synchronous transfer function and CD-DA transfer along subcode P,Q and R through W over SCSI function that host system can read CD audio data. This drive shows a highest performance such as100,000 hour MTBF. This drive can be used in a vertical position or horizontal position. This drive adopts RPC-II for its "Standard Specification Model". Refer to the precation of the next page for the RPC-II.

1/28

SD-M1401 Rev.1.0

Matters to be attended to: This drive adopts RPC-II for its "Standard Specification Model". This DVD-ROM Drive adopts RPC-II, the Phase II System of RPC (Regional Playback Control), on the basis of a contract with the CSS (Contents Scramble System) organization. The CSS rule requires that all the products not only DVD-ROM Drives but also PC systems installing DVD-ROM Drives sold from Jan.1, 2000 need to support RPC-II described above. To playback a DVD-Movie Software with the Regional Code specified by using a DVD-ROM Drive with RPC-II adopted, either the hardware or software used as applications on PC system side is also required to meet RPC-II. Namely, in the status that a hardware or a software for a DVD-Movie Playback Application planned to use in a PC does not support RPC-II, if the "RPC-II (Standard Specification) Drive" is used in combination, DVD-Movie Softwares with the Regional Code specified (most of DVD-Movie Softwares currently available on the market) cannot be reproduced. Especially, changing the RPC-II specification drive to the RPC-I is prohibited by the CSS rule. In the combination of the drive and PC system with RPC-II supported, as far as the Regional Code of a DVDMovie Software and the code memorized in the RPC-II Specification Drive coincides, the Movie Software is allowed to carry out. In the RPC-II Specification Drive, the region change by an end user is permitted up to 5 times in total including the initial region set. After change to the fifth region is carried out, the Drive enters Parm State ("no change allowed"status). The drive with Parm State is permitted up to 4 times of "reinitialization" by a drive manufacturer or a specific service center authorized by the CSS. Since it is considered that the reinitialization is carried out after the completion of the region confirmation through test items in the PC manufacturer's manufacturing line or the completion of drive repair, etc., the number of reinitialization times may vary from 0 (no reinitialization available) to 4 times. So, we recommend that not to disclose the reinitialization process to end users but only to inform the number of region setting times as "end user's direct region setting is available up to 5 times in total."

2/28

SD-M1401 Rev.1.0

2. Features (1) Internal 12 cm/8 cm DVD/CD/CD-ROM Drive (2) 5-1/4 inch Half Height Form Factor (3) Fast 105 ms Random Access Time (DVD) (4) Fast 85 ms Random Access Time (CD) (5) 13,500 KByte/s max. (DVD)/6,000 KByte/s max. (CD) Sustained Transfer Rate ( 1 KByte = 210 Bytes ) (6) CD Multisession Disc Spec (Photo-CD, CD-EXTRA) compliant (7) CD-R and CD-RW Disc Spec. compliant (Read) (8) Multimedia PC-3 Spec compliant (9) Windows PC2000 Spec compliant (10) RPC2 Compliant (11)Tray Type Electrical Load/Eject (12) Emergency Eject (13) Slant Angle : Horizontal +/-20° Vertical 0/10° (side to side): +/-10° (front to rear) ( In vertical mount, only 12 cm disc is applicable ) (14) Closed Enclosure (15) Snap-on Bezel (16) Built-in SCSI-2 interface Controller (17) Sync-Transfer on SCSI Bus (18) CD-DA Transfer Through SCSI Bus (19) Subcode P,Q,R-W Transfer Through over SCSI (20) CD Text Support (21) Built-in Mode-1ECC and Mode-2EDC (DVD/CD-ROM) (22) Embedded CD-ROM XA type ECC (23) 128KBytes Data Buffer Capacity (24) Media Removal Prevent Function (25) CD-DA Transfer Through SCSI Bus (8.6X CLV) (26) 8X Sampling & Digital Filter for CD Audio (27) High Speed Audio Playback System (28)16-Mode Output for CD Audio (29) Software Volume Control (CD) (30) 100,000 Power on Hours MTBF (31) Easy Serviceability (32) Remote SCSI-ID Jumper Block (33) Built-in Terminator (34) Low Power Consumption Ave: (CD) 10.8 W, (DVD) 7.2 W, Max : (CD) 12.6 W, (DVD) 8.8 W Stand-by 0.8 W

3/28

SD-M1401 Rev.1.0

3. Specifications 3.1.Performance (1) Applicable Disc *1 DVD: DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R (read) CD : CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, CD-I, CD-I Bridge (Photo-CD, Video-CD) Multisession CD (Phto-CD, CD-EXTRA, CD-R, CD-RW), CD-R (read), CD-RW (read) DVD-ROM: 2,048 Byte/Block CD-ROM : 2,048 Byte/Block (Mode 1) 2,336 Byte/Block (Mode 2) Data Cpacity/Disc: (1 GB=230 Byte, 1 MB=2 20 Byte, 1 KB=210 Byte) DVD-5 : 4.377 GB (4.700 Billion Byte) DVD-9 : 7.959 GB (8.545 Billion Byte) DVD-10: 8.754 GB (9.400 Billion Byte) DVD-18: 15.917 GB (17.091 Billion Byte) CD (Mode-1): 656.5 MB (688.4 Million Byte) CD (Mode-2): 748.8 MB (785.2 Million Byte) (3) Rotational Speed DVD DVD-R CD-ROM, CD-R CD-RW CD-DA Transfar CD-DA,Video-CD

(2) Data Capacity User Data/Block

: Approx. 5,800 rpm (4.1-10X CAV) : Approx. 1,100-2,800 rpm (2X CLV) : Approx. 8,500 rpm (17.2-40X CAV) : Approx. 4,300 rpm (8.6-20X CAV) : Approx. 1,800-4,300 rpm (8.6X CLV) : Approx. 1,200 - 2,000 rpm (4-5.7X PCAV)

(4) Transfer Rate ( 1 KByte=2 10 Byte=1,024 Bytes, 1 Mbyte=220 Byte=1,048,576 Bytes) Sustained Block Transfer Rate DVD: 2,770-6,750 Block/s CD : 1,297-3,000 Block/s Sustained Data Transfer Rate DVD: 5,540-13,500 KByte/s CD : Mode 1 2,595-6,000 KByte/s Mode 2 2,959-6,843 KByte/s 20 MByte/s ( Sync ) 5 MByte/s ( Async )

Burst ( SCSI Interface )

4/28

SD-M1401 Rev.1.0

(5) Access Time Average Random Access Time

DVD:*2 105 ms Typ CD:*3 85 ms Typ DVD:*4 100 ms Typ CD:*5 80 ms Typ DVD:*6 210 ms Typ CD:*7 190 ms Typ

Average Random Seek Time

Average Full Stroke Access Time

(6) Spin up Time ( Focus Search Time and Disc Motor Start up Time ) DVD: 1.5 s Typ CD: 1.4 s Typ

(7) Data Buffer Capacity

128 KByte

*1: All disc written in CD or DVD formats, except CD Red Book (audio), require additional specific application software and/or hardware. This drive referred in the specification is capable of reading these data formats. However, in order to run applications that use these formats you must first have the required software and/or hardware. *2: Measured by performing multiple accesses which means reads of data blocks over whole area of the media from 0 (h) block to 1E7725(h) (4.089 Billion Byte:87 % of total area) block more than 3000 times. Includes positioning, setting, latency time and ECC implementation time (if required). *3: Measured by performing multiple accesses which means reads of data blocks over whole area of the media from 00 min 02 sec 00 Frame to 60 min 01 sec 74 Frame (552.96 Million Byte:87 % of total area at linear velocity of 1.3 m/s) more than 3000 times. Includes positioning, setting, latency time and ECC implementation time (if required). *4: Measured by performing multiple seek which means seeks of data block over whole area of the media from 0(h) block to 1E7725(h) block more than 3000 times. Includes positioning, setting time which is same definition as HDD. *5: Measured by performing multiple seek which means seeks of data block over whole area of the media from 00 min 02 sec 00 Frame to 60 min 01 sec 74 Frame more than 3000 times. Includes positioning, setting time which is same definition as HDD. *6: Measured by performing maximum accesses which means reads of each data block of 0 (h) block and 1E7725(h) block alternately more than 100 times. Includes positioning, setting, latency time and ECC implementation time (if required) *7: Measured by performing maximum accesses which means reads of each data block of 00 min 02 sec 00 Frame and 60 min 01 sec 74 Frame alternately more than 100 times. Includes positioning, setting, latency time and ECC implementation time (if required)

(8) Load/Eject

(9) Air Flow (10) Acoustic Noise (11) Power Supply

(a) Electrical Load/Eject (Eject Button) (b) Load/Eject by SCSI command (c) Emergency Eject Not Required 43 dB (IEC 179 A weighted at 1 m) +5 V , +12 V (details in Section 7)

5/28

SD-M1401 Rev.1.0

3.2. Environmental Conditions This drive should be used under the conditions listed below. 3.2.1.Temperature and Humidity (1) Operating Temperature (2) Storage Temperature (3) Shipping Temperature (4) Operating Temperature Gradient (5) Storage Temperature Gradient (6) Shipping Temperature Gradient (7) Operating Humidity (8) Storage Humidity (9) Shipping Humidity (10) Condensation 3.2.2.Dust and Dirt

5 °C to 50 °C -10 °C to 60 °C -40 °C to 65 °C 11 °C/hour (max) 20 °C/hour (max) 20 °C/hour (max) 8 % to 80 % (wet bulb 27 °C max) 5 % to 95 % 5 % to 95 % In all the above conditions there must be no condensation unspecified

3.2.3.Vibration (1) Operating (1 Oct/min) ---------------- no hard error ----10 to 500 Hz 2.45 m/s2 [0.25 G] (0-p) (excluding resonance point) (2) Non-operating (1 Oct/min) --------- no damage ----5 to 10 Hz 5 mm (p-p) 10 to 500 Hz 9.8 m/s2 [1 G] (0-p)
(3) Shipping (Packaged) (1 Oct/min) -----

no damage ----10 to 25 Hz 9.8 m/s2 [1 G] (0-p)

X Y Z/30 min each

3.2.4.Atmospheric Pressure and Altitude (1) Operating (2) Shipping 3.2.5.Shock (1) Operating (DVD/CD )

0 to 3,000 m 0 to 12,000 m

---------------

no retry --------------14.7 m/s 2 [1.5 G] (Horizontal) 7.8 m/s2 [0.8 G] (Vertical) (Half sine wave 11 ms/10s interval) no data loss -------------98 m/s2 [10 G] (Half sine wave 11 ms/10s interval)

------------------------

(2) Non-operating (with no Disc mounted) ----- no damage ----490 m/s 2 [50 G] (Half sine wave 11 ms) (3) Drop (Packaged) ------------------(a) Bulk package (15 pcs.) (b) Bulk package (10 pcs.) (c) Individual Package no damage ----1 drop at 0.4 m (Bottom side only) 0.6 m drop once for each 6-surfaces, 1-edge and 1-corner 0.9 m drops once for each 6-surfaces, 1-edge and 1-corner

6/28

SD-M1401 Rev.1.0

3.3. Installation Conditions Mount the drive within 20° of the horizontal positions and within 10° of the vertical positions

+20° -20°

+20° -20°

a) Horizontal position

+10° 0° 0°

+10° -10° -10°

b) Vertical position Figure 1 Installation position

3.4. Dimension and Mass

----- See Figure 2 for details ----146 mm x 41.5 mm x 193 mm (excluding bezel) 0.95 kg (Net) 1.4 kg (Individual packaged) 10.8 kg (Bulk Packaged 10pcs.) 15.7 kg (Bulk Packaged 15pcs.)

(1) External Dimensions (W x H x D) (2) Mass (Weight)

7/28

SD-M1401 Rev.1.0

Figure 2

External Dimensions ( Unit: mm )

8/28

SD-M1401 Rev.1.0

3.5. Reliabilites 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----DVD: CD : Mode 1: Mode 2: (2) Seek Error Rate --- Allowing 5 Retries (default) 3.5.2. MTBF Assumptions: Power On Hours On/Off Cycles Number of Access Operating Duty Cycle

Allowing 5 Retries(default) ----10 -15 Max 10 -15 Max 10 -12 Max 10 -6 Max

100,000 h 5,436 h/year 313 cycles/year 600,000 accesses/year 20 % of Power On Time (Reading/Seeking) 0.5 h 15,000 h or 5 years (earlier one) 10,000 times or more 20 times or more 20 times or more

3.5.3. MTTR 3.5.4. Drive Life (1) Load/Eject (2) Interface connector Attach/Detach (3) DC Power connector Attach/Detach

4. Configuration See Figure 3 for details of the configurations 4.1. Electrical Circuits (1) Tray Eject Switch and Eject Detection Switch (2) Optical Pickup Servo Drive Circuit (3) Feed Motor Drive Circuit (4) Laser Diode Control Circuit (5) 8-16 Modulated data Demodulator, Error Correction Circuit and Disc Motor Control Circuit Copy Protector Circuit (DVD) (System Control Circuit, Digital to Analog Converter) (6) EFM Demodulator, Error Correction Circuit and DA converter Circuit (CD) (7) SCSI Control and CD - ROM Error Correction Circuit and SCSI I/O Interface Circuit

4.2. Optical Pickup

1-Lens and 2-Laser System Semiconductor Laser and 1-beam System (DVD) Semiconductor Laser and 3-beam System (CD) Brushless DC Motor DC Motor DC Motor

4.3. Spindle Motor 4.4. Feed Motor 4.5. Tray Load/Eject Motor

9/28

SD-M1401 Rev.1.0

DVD-ROM DRIVE MODEL SD-M1401 BLOCK DIAGRAM
TA1323F
RF Amp EQL Tracking Amp Data Slicer PLL D-RAM Interface ECC EDC
Analog Audio

TC94A03F

DRAM (1M)

Disc Motor Demodulator De-Scramble A/D D/A Track EQL D/A Focus EQL Feed EQL Disc EQL Clock Audio Decoder D/A D/A FG 22.58 MHz 40 MHz Clock ATAPI/DMA Interface Control De-Scramble SCSI Interface Control Sync/ID Detect Clock De-Scramble Header detect DRAM (1M) 66 MHz Converter Memory Controller Focus Amp Command Dec.

PUH

Loading Motor

Feed Motor

TA8493BF
Power Driver Power Driver Power Driver Power Driver BCA Decoder Audio D/A Servo Controller Digital

Position Detector

BA5983FM

Muting
ON/OFF

Eject Switch

DSP Interface FV Clock Converter

D-RAM Interface IDE / ATAPI Interface Control +5V CSS Authenticator 50P

Timer Micro Processor

Int. Control

LED

RAM

63F49AEPL
FLASH ROM

BUS Control

Tray Open/Close Detector

GPIO

LC897128

Error Correct

Digital Audio Encoder +12V

SD-M1401 Rev.1.0

AT49F1024

SCSI Connector

Figure 3 Configuration

10/28

Comparator

33.86 MHz

TC94A05 F

Terminator

16P

Mode Select headers

Disc Motor Drive

Analog Audio Out

4P

5.Functions 5.1. Disc Data Configurations 5.1.1. DVD-ROM Data Configurations Figure 4 shows how data is constructed in the case of dual layer/parallel track data DVD disc. The DVD spec defines the single layer, the dual layer/opposite and parallel track disc, that the DVD-ROM drive supports. For details refer to DVD Book Part 1. 1 block=1/676 s
ID Data (Dual layer Parallel track path) Layer No. 1 - Disc Information Lead-in Area ID No. ID No. xxh - 2FFFFh ECC Block 1 2 3 4 5 6 ID Data(4B) ID Data EDC(2B) nnnn Reserved (6B) Main Data (2048B) EDC (4B) Sector Format Type Tracking Method Refectivity Area Type: Data Area Lead-in Area

0

Data Area

~
Lead-out Area Lead-in Area

~ Approx. 130 k
ECC Block

~

~

~
ID Data(4B) ID Data EDC(2B) Reserved (6B)

~

Lead out Area Layer Number: Layer 0 Layer 1

xxh - 2FFFFh ECC Block 1 2 3 4 5 6 nnnn+15

Main Data (2048B) EDC(4B) ECC(160B)

1

Data Area

~
Lead-out Area

Approx. 130 k ECC Block

~

Figure 4 DVD-ROM Disc Data Configuration

5.1.2. CD-ROM Data Configurations Figure 5 shows how the data is structured in program units 1 block=1/75 s
TNO 0 1-Disc Time TOC Min Sec Block 1 Min Sec Block approx. 2 300 k-Blocks Block 2 Block 1 Lead-in

SYNC 12 bytes
Header User Data 2048 bytes in Mode-1 2336 bytes in Mode-2 4 bytes

Minutes Second(0~59) Blocks(0~74) Mode

~ ~ ~
ECC (Mode-1) 288 bytes

~ ~

~
AA

~

~
Lead out

Figure 5 CD-ROM Disc Data Configuration

11/28

SD-M1401 Rev.1.0

5.2. Power ON/OFF Timing Figure 6 shows the initialization sequence
Power ON or ATAPI-RST

Max. 200 ms "Command" Receivable

System Initialization Max. 3 s Focus Search Max. 4 s Spindle ON

Learning CD:Typ. 8 s, DVD 2 Layer Typ. 10 s, Max.60 s (Single Session Disc) Stand-by Acceptable "TEST UNIT READY" Command "Read-Command"

"Check Condition" Status

"Good" Status

Figure 6 Initialization Sequence

12/28

SD-M1401 Rev.1.0

6. Interface (1) The interface is based on SFF8090 Ver.2, MMC revision 7.0C and SPC revision 3. (2) The drive supports SCSI synchronous transfer and CD-DA data transfer over SCSI function. (3) The 128 KByte data buffer handles both high and low speed data transmission. (4) The largest block size on playback is 2,647 Bytes (Including Error Flags) The data length for each block is changeable by command. (5) On command execution, DISCONNECT processing and RECONNECT processing can be specified. (6) Command Link functions are usable.

6.1. Signal Lines (1) Logical levels of every Inputs and Output are logically false signals Input Low = 0 to +0.4 V=Logic '1' (true) Input High = +2.5 V to +5.25 V=Logic '0' (false) Output Low >/= 48 mA Output High = Open collector (high impedance) (2) The Term Power line has a protection inside of the drive to protect the power supply. This is shown in Figure 7.

+5 V

Protector

Diode

'TERM POWER' header SCSI Connector #26

Figure 7 Power Supply Line

6.1.1. Signal Line Termination Figure 8 and Figure 9 shows the method for daisy chain connection and Figure 10 and Figure 11 shows the method for radial connection. Always connect the terminator for SCSI because of the open collector configuration output drive. Also be sure to attach the frame ground for grounding with the host system. 6.1.2. Receivers and Drivers Figure 12 shows the construction and Figure 14 shows the interface pin assignments. 6.1.3. Connector Figure 13 shows the details of connector and Figure 14 shows the interface pin assignments.

13/28

SD-M1401 Rev.1.0

Max. 7 units connectable (SCSI Bus)

Terminator Drive 1 Drive 2 Drive 3

Terminator

Interface Card

Host System

Frame Ground

Figure 8 Daisy Chain Connection -- Turn off Internal Terminators from the drive if SD-M1401s are used as Drive 1 and/or Drive 2. ----

Max. 7 units connectable (SCSI Bus)

Terminator Terminator Drive 1 Drive 2 Drive 3

Interface Card

Frame Ground Host System

Figure 9 Daisy Chain Connection --- Turn off Internal Terminators from those drives -----

14/28

SD-M1401 Rev.1.0

Terminator

Terminator Drive 1

Terminator Drive 2

Terminator

Interface Card

Interface Card

Host System

Frame Ground

Figure 10 Radial Connection

Terminator Terminator Terminator Drive 1 Drive 2

Terminator

Interface Card

Interface Card

Host System

Frame Ground

Figure 11 Radial Connection ----- Turn off Internal Terminators from those drives ---

15/28

SD-M1401 Rev.1.0

Term Power ON/OFF +5 V
Terminator ON/OFF

+5 V

Terminator

Active Terminator 110 OHM

7438 or equiv.

74SL240 or equiv.

Controller

Drive

Term Power ON/OFF +5 V
Terminator ON/OFF

+5 V

7438 or equiv.

110 OHM

Active Terminator

Terminator

74SL240 or equiv.

Drive

Controller

Figure 12 Receivers and Drivers

16/28

SD-M1401 Rev.1.0

13.0

96.79 92.77 69.09 60.96 2.54 49 2.54 1 6.6 0.5 50 71.165 9.535 23.64 2
1.2

21.18 15.24 5.08

0.3

8.5

6.6

Figure 13 Interface Connector

17/28

SD-M1401 Rev.1.0

PIN No 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50

SIGNAL NAME -DB 0 -DB 1 -DB 2 -DB 3 -DB 4 -DB 5 -DB 6 -DB 7 -DBP GND GND GND TERM POWER (+5 V) GND GND -ATN GND -BSY -ACK -RST -MSG -SEL -C / D -REQ -I / O

PIN No 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49

SIGNAL NAME GND " " " " " " " " " " " NO CONNECTION GND " " " " " " " " " " "

Figure 14 Interface Connector Pin Assignment

18/28

SD-M1401 Rev.1.0

7. Power Requirements 7.1. Source Voltage +5 V +/-5 % (Operating) +12 V +/-5 % (Operating) +/-8 % (Start up) +/-8 % (Start up) 100 mV 100 mV
(p-p)

7.1.1. Spike 7.1.2. Ripple

Max. Max.

(p-p)

7.2. Current Drain (Typical value) 7.2.1. Sleep 7.2.2. Standby (Laser off, Motor off) 7.2.3. Continuous Read (Data/Audio) +5 V 130 mA (DVD/CD) 160 mA (DVD/CD) 610 mA (DVD) 570 mA (CD) 420 mA (DVD) 410 mA (CD) +12 V 2 mA (DVD/CD) 3 mA (DVD/CD) 320 mA (DVD) 630 mA (CD) 90 mA (DVD) 110 mA (CD)

7.2.4.Idle (Laser on, Motor on)

7.2.5. Average (20% Random Access)

560 mA (DVD) 530 mA (CD) 630 mA (DVD) 590 mA (CD) 790 mA (DVD) 730 mA (CD)

370 mA (DVD) 680 mA (CD) 470 mA (DVD) 800 mA (CD) 980 mA (DVD) 1,570 mA (CD)

7.2.6. Maximum (100% Random Access)

7.2.7. Peak in executing Access (Exclude Spike Current) *Spike: Less than 1 ms of duration

7.3. Connector (SCSI and Power Hybrid type) Figurer 15 shows the external appearance of the Power Supply Connector. Use IRISO ELECTRONICS P/N9047B-54Z12-GT or equivalent. PIN #1: +5 V PIN #2: GND PIN #3: GND PIN #4: +12 V Figure 15 Power Supply Connector

#1

#2

#3

#4

19/28

SD-M1401 Rev.1.0

8.Audio (Test condition:Ordinary temperature) ----- Specification for Red Book Disc ----Output : 2 channel (Analog Audio) Sampling Frequency : 44.1 kHz Quautization : 16 bit linear 8.1. Line Output --- in case of attenuator is set at 0 dB by the command --(1) Output Level 0.83 V (rms Typ) (2) Type Unbalanced (3) Load Impedance 47 kOHM min (4) Frequency Response 20 Hz to 20 kH +/-3 dB (5) Distortion -80 dB (at 1 kHz JIS A-weighted) (6) Signal to Noise Ratio 90 dB Typ (IEC 179 A-weighted) 8.1.1.Connector Figure 16 shows, the external appearance of the 4P Audio Connector (Connector, Part No. 6156B-04A-PP, made by IRISO ELECTRONICS Corporation or equivalent is used.) PIN #1: L PIN #2: GND PIN #3: GND PIN #4: R #4 #3 #2 #1

Analog Audio

R

GND

GND

L

Figure 16 Audio Connector

8.2. Audio Modes (1) 16 Modes including 'stereo', 'Lch Mono', 'Rch Mono', and 'Mute' are selectable by command. Default mode is 'Stereo'. Audio out is automatically muted in the digital area and seek state. (2) 16 Steps of attenuation level for the Audio Output is selectable by command. Default level is 0 dB.

20/28

SD-M1401 Rev.1.0

9. Jumper Setting/Feature Selections Set up of SCSI-ID number, Parity Check function, Host Interface Transfer Block Size function and CD-Audio Playback mode etc. are available by shorting these Headers.

ID 4

ID 2

TERM ID 1 PRTY ON/OFF

512/2k

POWER TEST SUPPLY

Figure 17 Mode Select Headers

9.1. SCSI-ID (ID 1, ID 2, ID 4) (Default ID) This 3 bit binary header sets the SCSI-ID number. When setting numbers, follow the application software instructions. Header SCSI-ID 0 1 2 3 4 5 6 7 O: Open LSB ID 1 O S O S O S O S S: Short ID 2 O O S S O O S S MSB ID 4 O O O O S S S S

9.2. Parity (PRTY) To enhance data bus reliability, set this Header to "S" to activate the parity bit check function on SCSI data bus. This setting cannot be used if no parity generation function is provided on the I/F card. Header O S O: Open Description The drive does not check parity although the output parity is effective. The drive checks parity, and also the output parity is effective. S: Short

21/28

SD-M1401 Rev.1.0

9.3. Terminator ON/OFF (TERM ON/OFF) This Head setting turn on or turn off the terminator. Header O S Description The terminator is turn off. The terminator is turn on. S: Short

O: Open

9.4. Host Interface Transfer Block Size (512/2k) This Head setting chooses 2048 Bytes Mode or 512 Bytes Mode on Host Interface transfer. Header O S Description Allow 2048 Bytes Mode. (Support CD and DVD) Allow 512 Bytes Mode . (Support only CD) S: Short

O: Open

9.5. Audio Playback (TEST) This Header setting selects the drive operation between normal CD-ROM and CD-Audio player mode. When "S" is selected, command from the host computer is ignored. Also CD-Audio disc or audio tracks in CD-ROM disc is playable by the command when the Header is set for "0". Header O Description Normal operation mode to connect the host computer. (ID 1, ID 2, ID 4 and PRTY Headers should be set for O) CD-Audio disc playback mode. Allows repeated play from beginning of the program area up to the last when the disc is loaded. Pushing the Eject Button for shorter than 1 s allows proceeding to beginning of the next track number but not acceptable during access. Pushing the button more than 2 s stops playing and ejects the Tray. S: Short

S

O: Open

22/28

SD-M1401 Rev.1.0

9.6. Terminator Power Supply (POWER SUPPLY) This header setting switches to supply the power (+5 V) to the other equipments through the SCSI connector or not. Header O S Description No power is supplied from the drive. Power is supplied to the other peripherals through SCSI Connector (Pin No. 26). S: Short

O: Open

9.7. Jumper (Part Number T/E) Use P/N 9251H-GF made by IRISO Electronics or equivalent. 9.8. Recognition of Setting As the setting recognition is performed only after power On, turn power off and then On again whenever change is made.

23/28

SD-M1401 Rev.1.0

10. Busy Indicator The LED of Front Bezel indicates the drive status. (Busy Indicator) (1) After Tray is closed, Busy Indicator start blinking at 0.8 s intervals, and then ----(1-1) Turns off when the drive in the 'Idle' status.
0.8 s

Light Off

Figure 18 Idle (1-2) Continuously off when no disc is mounted.
0.8 s

Light Off

Figure 19 No disc

(1-3) Continuously on when media has problem
0.8 s

Light On

Figure 20 Media Problem (2) When playing an audio track, Busy Indicator is blinking at 1.6 s intervals.
1.6 s

Figurer 21 CD-Audio playback (3) When performing 'Data Access' and during 'Data Transfer' Busy Indicator keeps turn On. Light On Figurer 22 Data Access and Data Transfer

24/28

SD-M1401 Rev.1.0

11.Connection 11.1. Power Supply Cable (1) Housing (2) Contact (3) Cable Length

AMP JAPAN P/N 1-480424-0 or equivalent AMP JAPAN P/N 170148-2 or equivalent AWG 28 Max. 2 m

11.2. Interface Cable (1) Connector (2) Cable Specific Impedance Length

SCSI specification 50 core type 100 OHM +/-10 % (without shield) Max of 6 m for total SCSI bus length Max of 3 m for total SCSI bus length (FAST SCSI) Max of 1.5 m for total SCSI bus length (Ultra SCSI)

11.3. Audio Cable (1) Capacitance (2) Length

Unbalanced and shielded Less than 1000 pF Max. 3 m

12.Emergency Eject Execute following procedure only in the case of emergency (Tray will not eject and disc can not be removed although pressing Eject Button). (1) Turn the drive supplying power off. (2) Insert solid bar (like paper clip) into Emergency Eject hole and push as shown in Fig.23. Then Tray will be ejected. (3) After removed the disc, gently push Tray to close.

50 mm

diameter 1.0 to 1.5 mm

Figurer 23 Insert the bar

25/28

SD-M1401 Rev.1.0

13.Safety Standards/Agency Approvals (1) Safety EN60950 UL 1950 CAN/CSA-22.2 No.950 FDA CFR21, EN60825
: 1992 [Residential, commercial & light industry] : 1998 [Class B (inclding domesstic enviroment)] : 1998 [Information technology equipment-Immunity characteristices - Limits and methods of measurement] EN61000-4-2+A1 : 1995+1998 [CD:4 kV, ID: 4 kV, AD:8 kV] EN61000-4-3 : 1996 [3 V/m, 80-1000 MHz, 1 kHz 80 % AM ] EN61000-4-4 : 1995 [AC-line: 1 kV, I/F 0.5 kV, f: 5 kHz, Polarity: +/- ] EN61000-4-5 : 1995 [AC-line: 2 kV/1 kV, Polarity: +/- ] EN61000-4-6 : 1996 [3 V, 0.15-80 MHz, 80 % AM] EN61000-4-8 : 1993 [1 A/m, 50 Hz] EN61000-4-11 : 1994 [>95 % 0.5, 30 % 25, >95 250] EN50081-1 EN55022 EN55024

(2) Laser (3) CE

14. Electrostatic Discharge Standard (1) Operating (2) Damage including IEC801-2 8 kV or less 15 kV or more

15. Accessories 1-Safety Instruction Manual 5-Short Jumper (Installed in 'TERM' header and GND to GND)

16. Packaging (1) 15 unit in a bulk package 24 bulk packs on one pallet. *All transportation is allowed with pallet. (Transportation with bulk package is not allowed.) 28 bulk packs on one pallet. (Transportation with bulk package is allowed.)

(2) 10 unit in a bulk package

17. CE Declaration of conformity Please refer to attached Annex 1.

26/28

SD-M1401 Rev.1.0

TOSHIBA
Product: Manufacturer(s): DVD-ROM Drive

TOSHIBA EUROPE GMBH

EU-Declaration of Conformity
Toshiba Corporation 1-1, Shibaura 1-chome, Minato-ku, Tokyo 105-8001 Japan See page 2 for other locations Model: Options: SD-M1401 None

Toshiba declares that the above mentioned product(s) with or without the listed options comply to the EU-Directives and standards as listed on page 2. Last two digits of the year in which the CE mark affixed : 00 Responsible for CE-marking: Signed by: Place: Date: Signature: Toshiba Europe GmbH Mr. F.Yamashita, President of Toshiba Europe GmbH D-41460 Neuss March 10,2000 ----------------------------------------------------------

This declaration certifies compliance with the listed directives, but does not constitute an assurance of characteristics. The safety information in the supplied product documentation must be observed. ............................................................................................................................................................ Document No.: YEA-R150 Page: 1 of 2 ............................................................................................................................................................ [History if issue] Issued : Mar.9, 2000 ................................................... Revision A : Ref.: ................................................... ......................... Revision B : Ref.: ................................................... ......................... Revision C : Ref.: ................................................... ......................... Revision D : Ref.: ................................................... .........................
TOSHIBA EUPOPE GMBH HAMMFELODAMMB.D-41460NEUSS POSTFCH 101482. D-41414 NEUSS TELEFON: (02131) 158-01 TELFAX : (02131) 158-341 GESCHAFTSUHRER HISATSUGU NONAKA HRB 3479 AMTSGERICHT NESS

Annex 1 27/28
SD-M1401 Rev.1.0

EU-Declaration of Conformity
Issude Level/Test condition EN50081-1 EN55022 EN55024 EN61000-4-2+A1 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 Related EU-Directive 89/336/EEC 1995 1995 1996 1993 1994 AC-line: 1 kV, I/F 0.5 kV, f: 5 kHz, Polarity: +/AC-line: 2 kV/1 kV, Polarity: +/3 V, 0.15-80 MHz, 80 % AM 1 A/m, 50 Hz >95 % 0.5, 30% 25, >95 250 1995 +1998 1996 CD: 4 kV, ID: 4 kV, AD: 8 kV 3 V/m, 80-1000 MHz, 1 kHz 80 % AM 1992 1998 1998

ED-Directive

Related Standard

899/336/EEC (EMC Directive)

EMC-emission:

EMC-immunity

Residential, commercial & light industry Class B (inclding domestic enviroment) Information technology equipment-Immunity characteristices-Limits and methods of measurement

Product/Options

Model

DVD-ROM Drive X Address

SD-M1401

28/28
YEA-R150 2 of 2 Revision:

Manufactuer(s) Location

Toshiba Multi Media Devices Co, Ltd Toshiba Misawa Media Devices Co, Ltd EMS Corp. Hokuto Communication Industrial Co., Ltd. Yuzawa Denshi Kogyo Co., Ltd. Tsugaru Technica Co., Ltd. Emusu Itayanagi Co., Ltd. Toshiba Information Equipment (Philippines) Inc

Integrated Microelectronic Inc. EMS Kizukuri Corp. EMS Fukaura Co., Ltd

19 Minase, Fukihata Goshogawara-shi, Aomori 037-0003 Japan 3-31-2779, Minami-cho, Misawa-shi, Aomori-ken 033-0036 Japan 4-5 Shoubu, Ubayachi Goshogawara-shi, Aomori 037-0015 Japan 207 Aza Koamon, Rokugo, Rokugo-machi, Senboku-gun, Akita 019-1404 Japan 257 Nakano Yuzawa-shi, Akita 012-0041 Japan 81-87 Iwai, Aiuchi, Shiura-machi, Kitatsugaru-gun, Aomori, 037-0401 Japan 13-10, Matsumoto, Tsuji, Itayanagi, Kita-Tyugaru-gun, Aomori, 038-3645 Japan 103 East Main Avenue Extension, Special Export Processing Zone, Laguna Technopark, Binan, Laguna Philippines North Science Avenue Laguna Techno Park Inc. Binan, Laguna Philippines 1-2 Aza-Miyazaki, Kizukuri-machi, Nishi-Tugaru-gun Aomori 038-3157 Japan 24-1 Aza Azumazawa, Ohaza Fukaura, Fukaura-machi, Nishi-Tsugaru-gun, Aomori, 037-0401 Japan

Document No.:

SD-M1401 Rev.1.0

Page:

Deviation List
Page 3 8 21 Item 2. Fuatures Figure 2 9. Jumper Setting Rev # 0.8 Rev # 1.0

(4) Fast 80 ms Random Seek
TENTATIVE Set up of........, Eject Button inhibit function and CD-Audio

(4) Fast 85 ms Random Access
Non-tentative Set up of........, Host Interface Transfer Block Size function 512/2K POWER SUPPLY 9.4. Host Interface Transfer Block Size (512/2k) This Head setting chooses 2048 Bytes Mode...... Allow 2048 Bytes Mode (Support CD and DVD) Allow 512 Bytes Mode (Support only CD) 9.6. Terminator Power Supply (POWER SUPPLY)

Figure 17

PRV/ALW TERM POWER 9.4. Media Eject Prevention (PRV/ALW) This Head setting enables or

22

9.4. Host Interface Transfe...

9.4. Host Interface Transfe... Header O S

Allow the Tray eject Prevent the Tray eject. Eject button is ignored. 9.6. Terminator Power Supply (TERM POWER)

23

9.6. Terminator Power Supply

SD-M1401 Rev.1.0