Matsui VXA1105 free download

File name MaVX1105.pdf

MATSUI VXA 1105 Alignments & Adjustments 1-6: MAIN PCB AND BACK PANEL (Refer to Fig. 1-6) 1. Remove the 2 screws (1). 2. Remove the Main PCB in the direction of arrow. 2. REMOVAL OF DECK PARTS 2-1: LINK GEAR (R) / CLUTCH GEAR (Refer to Fig. 2-1) 1. Unlock the support (1). 2. Remove the BOT Sensor Cover and BOT Reflector. 3. Unlock the 3 supports (2). 4. Remove the Side Bracket R2 and Spring Earth. 5. Remove the Flap Lever, Link Gear (R) , Cam Gear Ass'y and BOT Lever. Fig. 2-3 NOTE When installing the Link Ass'y and Link Gear (R), align the timing Marks. 1 NOTES 1. Do not touch the head by any means when replacing the Audio Control Head. (Use gloves.) 2. After replacement, confirm the following adjustments. a. MECHANICAL ADJUSTMENTS: ITEM 2-2 b. MECHANICAL ADJUSTMENTS: ITEM 2-3 2-4: CASSETTE SIDE R (Refer to Fig. 2-4) ig. 2-8 1. 2. 3. 4. 5. 6. Unlock the 2 supports (1). Remove the Cassette Side R. Remove the Pack Spring. Remove the Locker Spring. Unlock support (2). Remove the Locker R. Fig. 2-6 2-7: TENSION BAND (Refer to Fig. 2-7) 1. 2. 3. 4. 5. 6. Remove the Tension Arm Spring 1. Remove the Tension Arm Spring 2. Remove the Tension Adjust. Remove the Tension Arm Ass'y. Remove the Tension Band Ass'y. Remove the Tension Lever 2 Ass'y. 2-9: PINCH ROLLER / CASSETTE OPENER (Refer to Fig. 2-9) 1. Unlock the support (1). 2. Remove the Pinch Roller. 3. Remove the screw (2). 4. Unlock the 2 supports (3). 5. Remove the Cassette Opener. 6. Remove the Spring P5 and Arm P5 Ass'y. 7. Remove the Cam Gear and Cam Pinch Roller. 8. Remove the polyslider washer and Cam PS. NOTES 1. Do not touch the Pinch Roller. (Use gloves.) 2. When installing the Cam P5, Cam Pinch Roller and Cam Gear, align the timing marks. Fig. 2-4 2-5: CASSETTE SIDE L (Refer to Fig. 2-5) Fig. 1-6 1-7: CHASSIS SECTION AND UNIT ASS'Y (Refer to Fig. 1-7) 1. Remove the screw (1). 2. Remove the screw (2). 3. Remove Unit Assy in the direction of arrow (A). NOTE When installing the Unit Ass'y, align the timing marks and pull the Cassette Holder Ass'y in the direction of arrow (B). Fig. 2-10 2-11: CYLINDER UNIT (Refer to Fig. 2-11) 1. Disconnect the following connectors: (CP4101 4 pins and CP4102 5 pins). 2. Remove the Joint Screw, then remove the Azimuth Spring. 3. Remove the 2 screws (1) then remove the Polyslider Washer and Cylinder Unit from the Main Chassis. Fig. 2-1 2-2: TOP BRACKET / TAPE PIECE GUIDE (Refer to Fig. 2-2) 1. Unlock the 4 supports (1). 2. Remove the Top Bracket. 3. Remove the Side Bracket R1 and Side Bracket L. 4. Unlock the support (2). 5. Remove the Joint Gear. 6. Remove the Bracket R Spring. 1. 2. 3. 4. 5. 6. Unlock the 2 supports (1). Remove the Cassette Side L Remove the Pack Spring. Remove the Locker Spring. Unlock the support (2). Remove the Locker L. Fig. 2-7 NOTE 1. Install the Tension Band Assy without twisting it. 2. Oil (kyoudo oil slaidasu #150) the area marked with A in Fig. 2-7. 2-8: REEL DISK (Refer to Fig. 2-8) 1. Remove the Reel Disk S and Reel Disk T.