Information about the files in archive: |
Decompress result: | OK |
Extracted files: | 11 |
File name | | Text |
00CLA2.pdf | | © Electrolux |
116EN.pdf | | SERVICE BULLETIN
NOT CONFIGURED ELECTRONIC BOARDS (Rev. 02)
In the sections: "Electrical equipment" in Washing machines, Washer-dryers, Dryers and Dishwashers spare part lists. "Diffuser" or "Cooling Unit" in Refrigeration appliances.
the "configured electronic board", identified by the first digits "973" of the spare part, is featured, where possible. Also the "not configured electronic board" can be indicated in the same sections and with the same position. The configuration of this board is possible only if you have the suitable equipment (software and hardware) for this type of activity and if you have taken part to the training. It is still not possible to programme the not configured electronic boards in all Countries.
ATTENTION: We will not accept returns of not configured electronic boards that have been wrongly ordered or that are damaged in some parts.
For any further question please contact your local Service Representative.
REVISIONS: Revision 00 01 02 Date 05/2008 06/ |
11EN.pdf | | Circuit Diagram
Technicl Specifications
GENERAL FEATURES Supply voltage ... 230 V Dimensions (height, width, depth) ... 85/40/60 cm Dryclothes loading capacity ... 5,5 kg Drum rotation speed (washing/spinning)55/600-1500 r.p.m Intermediate speed ... 1000 r.p.m Intermediate speed ... 850 r.p.m WATER LOAD CAPACITY (without clothes) : Heating Level I ... 2 l Heating Level II ...2 l Anti-overflow level ... 43 l WATER PRESSURE : Max./Min. ... 0,8/0,05 MPa CONSUMPTIONS (COTTON 60°) : see energie label TECHNICAL PARTICULARS DRAIN PUMP : Maxi head ... 100 cm |
128EN.pdf | | Toploader Changing drum lid at ALENA Exchange of the drum lids a) b) Remove the left and right side Panel Depending on the version of the appliance: Remove left and right weight without recess (see figure 1) do not remove weight with recess. Attention! By appliances with Jet-System, loosen the tube.
c)
The right and left side wall of the tub each shows a marking for a hole. These markings have to be opened using the enclosed punch (see figure 2).
d)
Turn the drum until the axle of the drum lid matches with the holes in the side wall of the tub (see figure 3).
HV844-N 12.01 R.B.
599 51 31 28 EN
Knock out the axle using the enclosed punch. The drum lid can be removed. (see figure 4,5 and 6)
For the second drum lid repeat the process d).
Exchange of spring and softopening a) Loosen the shackle in the middle: Mark the point with a punch and rebore the center punch mark with a 5 mm drill, deburr the shackle (see figure 7 and 8)
HV844-N 12.01 R.B.
599 51 31 28 EN
b)
Version with |
1B1.pdf | | © Electrolux |
2.pdf | | © Electrolux |
210EN.pdf | | Service-Bulletin
Washing machines Toploader Discoloration at the rubber bellow
Concerns: Cause: All ALENA appliances with carboran drum lid
599 521 210
EN
Depending on water quality and kind of water lines to the washing machine it is possible that rust-brown deposits may arise ahead and rear at the rubber bellow. According to a material analysis by the Henkel company, this discoloration contains high parts of iron as well as copper and manganese. Depending on fouling factor it is possible to clean the brown discoloration at the rubber bellow with a commercial household detergent. When a cleaning is no more possible, the rubber bellow can only be replaced.
Measure:
DGS-TDS-N 02.12.04
© Electrolux |
215600.pdf | | STR 108 215 600
© Electrolux |
2156002.pdf | | VDR 108 215 600
© Electrolux |
73502.pdf | | |
C3CLA2.pdf | | © Electrolux |
LU1.pdf | | © Electrolux |