PANASONIC CY-PA2003N free download

File name PANASONIC CY-PA2003N.pdf

ORDER NO. ACED060723C2 AUTOMOTIVE AFTERMARKET CY-PA2003N 2 Channel Power Amplifier Specifications* General Power Supply DC 12V (11V - 16V), Test Voltage 14.4V Negative Ground Current Consumption Speaker Impedance Power Output ("EIA" Power) 1-CH (Monaural) 2-CH (Stereo) Maximum Power Output 1-CH (Monaural) 2-CH (Stereo) Total Harmonic Distortion Low Pass Filter High Pass Filter Bass Boost Signal to Noise Ratio Frequency Response Input Sensitivity Input Impedance 550WЧ1 (20Hz-20000Hz, 10%) 260WЧ2 (20Hz-20000Hz, 10%) 0.08% (1000Hz, at 10W) 50Hz-250Hz 50Hz-250Hz 0dB-15dB (Middle Frequency: 45Hz) 90dB (IHF, A) 20Hz-20kHz 0.2V-6V More than 43k 480WЧ1 (20Hz-20000Hz, 1%, 4 ) 200WЧ2 (20Hz-20000Hz, 1%, 4 ) 44A (at 200WЧ2) 4 * Specifications and the design are subject to possible modification without notice due to improvements. ** Dimensions and Weight shown are approximate. ** Above specifications comply with EIA standards. Dimensions (WЧHЧD)** Weight** 280Ч62Ч333 mm 4.5 kg © 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. CY-PA2003N CONTENTS Page 1 ABOUT LEAD FREE SOLDER (PbF) 2 FEATUERS 3 REPLACEING THE FUSE 4 DIMENSIONS 5 WIRING CONNECTION 6 IC BLOCK DIAGRAM 2 2 2 2 3 3 7 REPLACEMENT PARTS LIST 8 EXPLODED VIEW (Unit) 9 WIRING DIAGRAM 10 SCHEMATIC DIAGRAM 11 BLOCK DIAGRAM Page 4 9 10 15 19 1 ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB. Caution : · Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 40°C) higher. Please use a soldering iron with temperature control and adjust it to 700 ± 20°F (370 ± 10°C). In case of using high temperature soldering iron, please be careful not to heat too long. · Pb free solder will tend to splash when heated too high (about 1100°F/600°C) · This lead free solder will be used for the products after serial No. 1,000,001. 3 REPLACEING THE FUSE Use fuses of the same specified rating 25 amps. Using different substitutes or fuses with higher ratings, or connecting the unit directly without a fuse, could cause fire or damage to the stereo unit. 4 DIMENSIONS 2 FEATUERS · 600 W Ч 2channel maximum power output · Total 1200W maximum power output · Low-Pass Filter for subwoofer, High Pass Filter · Hight Level Speaker Input connection · Bass boost control system · Crossover Frequency Control · RCA output terminals · 5.1-channel Surround System (Combination with other Panasonic car audio products) 2 CY-PA2003N 5 WIRING CONNECTION 6 IC BLOCK DIAGRAM UP1 : 07-00494-00 3 CY-PA2003N 7 REPLACEMENT PARTS LIST Notes : 1. Be sure to make your orders of replacement parts according to this list. 2. Important safety notice: Components, identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturerґs specified parts. 3. Location keys in the