| Subject | Text |
| 75 ohm connector repair | The 75 ohm cable connector broke off the back of the television. Can I fix this myself? If I take th |
| 04/13/2011 10:05 PM 612,477 6507_00b.pdf
04/13/2011 10:05 PM 1,215,173 80A_.pdf |
|
|
| Newsflash: TV IS FIXED!!! yay!
There was a hairline crack on the HOT emitter pad from changing th |
| Check/replace these components in the ABL-line, 2x SMD-zenerdiodes 6,8V, 1x SMD-diode 1N4148 and 1x |
| Re: Same TV, Same Problem.... | Hi..just to shere my knowledge..i from malaysia but i think the basic still same..i have lot experie |
| Replace all three cap the one 300 ohm resistor and the vertical IC still has a horizontal claps.
N |
| Re: diagram | [quote:d9d12eaf63="picasso"]I have the crt panel-diagram.I can send it to you if you like.
PS : 1 |
| want to build a power supply | hey guys [color=red:52718d60be]i want to build a power supply but not just any power supply i want t |
| RESISTOR PROBLEM | HELLO, The first thing I would ask is what the amps total of the circuit would be that this fuse is |
| Well, any high voltage capacitors could give a nasty shock if fully charged, they can be discharged |
| update | VS/VA voltages read 0. After finding another guide that showed me how to force the commands I saw t |
| Assuming TV DOES turn On & Off at your command with No Vert deflection: D445 cathode 24vdc?
R44 |
| Denon | Hi Roger,
the power button is flashing because the unit goes into protection. Check the power tra |
| Banished mod minnie | Check HOT for a short, regulator MX0841 with MX0842, and R807 .1 ohm 1 watt to see if it's open. |
| Looking from the top of the board, both R105, R106 are next to a CN2 connector. As it was said, use |
| Hi vtech, thank you very much for your kind answer and especially for your illuminating explanation. |
| I guess you need to begin with why you are troubleshooting an amp circuit. If the fuses are already |
|
|
| Yes, if the discharge is of high enough energy, but in normal circumstances - such as those which ca |
| dont forget to change low ohm resistor off flybackthat feeds the voltage usually 26volts to the vert |
| pioneer pro 119 converg. board resistor R2604 | this is a solid white resistor thats marked as a 2.2 ohm-J and is reading at 1.3 ohm. i want to repl |
| resistor | it is a 6.8k ohm 1/8w 5% resistor |
| VW Polo TDIl model 11/2004 | where and how to conect door locking ?
i found wires that come from left door there is one wire
bl |
| They should be 6.3 ohm resistors not 630. |
| My Tv just did the same thing | What I found was that the fuse was blown, I replaced the fuse plugged it in and once I powered it u |
| you are talking about the stk392-110's correct?? can anything cause those 1 ohm resistors to burn o |
| SC-HT900 fan issue | I have found a fix that used a 220 ohm resistor to bypass Q510 transistor (emitter to collector) but |
| 3045 is a 2.2 ohm 0.125W resistor |
| Channel out on old Technics | Thanks RiffMaster, you were right! It's been quite awhile since I tried to trace circuits and then i |
| Zenith ZB4683RK convergence problem | Hello, If you look at the pics at
http://webpages.charter.net/jenglish_tnx/
you will see what I s |
| you may want to check you speaker and make sure it is not bad also, make sure it is 4 ohm. |