| Subject | Text |
| yeah! tv still working but, always need to push the reset button in front. otherwise no signal with |
| repairing an old sansui amplifier | hello every one ,
new member here and also newby in the electronic repair
i have an old sansui |
|
|
| Do not have the T-230 schematic, but I think it was similar to T-240. As far as backup on any digita |
| DTK CDD1401 and Markvision VC4968NI Monitors | I need service manuals or schematic diagrams for two old monitors I am trying to repair. They are a |
| What about units that wont power on? I assume from the previous post that the main cost in a flat pa |
| Dead Black Diamond BD28WS | Hello to everyone this is my first post here. I have a BD28WS Black Diamond TV. The fault is when I |
| Looking for Pioneer VSX-D307 Receiver Service Manual | I'm looking for a service manual (or at least a schematic) for my Pioneer VSX-D307 Receiver.
Anyo |
| voltage for relay | hi,i have a problem on my yamaha rx-v392 model...i need to know what is the voltage of the relay in |
| defective software for 6600 | hi!
i would like to post a question regarding my nokia 6600,,im having a hard time looking for the |
| What you are describing is identical to the issue which only affected the DVD operation cycle but I |
| SUBJECT: DIGITAL CONVERGENCE ADJUSTMENT MODE ACCESS
Details:
In the past, when the technician need |
| Re: Onkyo TX-SV535 Amp / Remote Speakers NOT Working | [quote:586d3411be="kayecross"]I can not get the remote speaker button to work on my amp. I have inst |
| Hi again,
By bypassing the main speaker relay everything works great. Does anyone know if this mi |
| avr 130 one of the surround outputs is very very low | got a harman kardon avr 130 one of the surround outputs is very very low
when i connected speaker t |
| Re: AVC | [quote:23d123f2da="jts1957"]What is AVC?
I'm presuming power strip or surge protection?[/quote:23d1 |
| Denon DN-2600F Cable Pinout | I need to make a replacement interconnect cable that goes between the two units. Could you pleas oh |
| On closer look, obviously the spindle is of a different type that I originally thought. (Hall effect |
|
|
| Re: Do this test | Forgot to mention: Keep CD player's volume quite low to keep from exceeding input level rating of yo |
| Protect mode occurs when an overcurrent situation is detected by the power supply in the amplifier. |
| Headphone circuit for TV needed. | Hello all. I hope this is the right place for my question. Ok, I have a infrared wireless headphon |
| [quote:3c401903bc="minnie"]By the end of the year vcr’s will be extinct. DVD burners have come down |
| [quote:52c49ffcc4="Kossta"]Excuse me. I also need code for VDO CRD 500
GM050011217145.
Thank you |
| Re; Checking "lenses" | I presume you mean the Laser.
All CD / DVD units have one (sometimes two) laser assembly. Generally |
| Blowing speaker protection fuse suggests failure of the power amplifier output transistors. If a DVM |
| Hi,
Few things u can check:
1. Does the set power up?
2. Speakers - are they connected prop |
| Siemens Gigaset 4010 Comfort problem | Can make call but can't disconnect (end it.) If I call someone and try to end call only sound is tur |
| JVC XV-THA30 DVD Surround Receiver Problem | I remember when these first came on the market and we had several faulty units that were sold to cus |
| Philips 26" LCD TV Model # 26FW5220/37 | I have a few units of the LCD TVs i would like to know what do i need to do to make it work in HDMI |
| Re: let's start over | Did the two units ever work well together, or this is the first time you've tryed to connect this TV |
| I agree with Miguel. if your mixer has PAN controls just turn all of them to the same end so your ch |