| Subject | Text |
| Hi minnie and thanks for the reply.
Is there any way to determine if it's the Y sustain or the Y |
| european capacitor codes | found a schematic on a french site that I'd like to build.
Here's a couple capacitors that have th |
|
|
| Adcom Motorized Pot. - Help | I have an old Adcom GTP-500 Tuner/Preamp that I dealry love. It still works great. My remote control |
| 50mp1 | I have a plasma sync m50p1 out of warranty. when I turn it on I only get a bleeding screen in the mi |
| [b:504d4d7d37]Mike454ci[/b:504d4d7d37],
It's Samsung chassis, if you'll write the main parts like C |
| Philips Remote | My remote did the same thing couple of years ago for no reason. Not droped, wet or anything. Just s |
| huh | [quote:2e4b832b38="Anonymous"]you cannot ever determine a good device. any tester will tell you as g |
| Actually how would I determine with of the two is the culprit? and my question above ! |
| I believe you will determine they [b:d59a51a3db]ARE CRTs[/b:d59a51a3db] (Cathode Ray Tubes), Not lam |
| yamaha emx512sc | I have the mics set at about 2 and the mains set at about 2 so the volume output is not really hot. |
| Thank you very much for your reply.
I have taken the back of the TV off now to see if there was |
| I NEED A PICTURE OF THE SCHEMATIC DIAGRAM OF THIS MODEL | I WANT TO DETERMINE THE EXACT VALUE OF THIS BOARD NUMBER R601 |
| Black and Decker 9.6 to 18 Volt Charger | I have recently been asked to look at a damaged Black and Decker Multivoltage charger model # BDMVC- |
| The only way to determine what the problem is would be by examining the supply on the bench - remote |
| Should not be difficult to determine as to why your sub/w is not working. Did the "blown caps&q |
| Yamaha MCX_1000 Lightning damage? | We are an authorized Yamaha servicer and not all that often see the MCX-1000
A customer came in w |
| [quote:94e0ba6fc6="dahbrown"]There is no voltage on the -15v rail. The resistance was around 400 ohm |
|
|
| Thanks again Richard,
Thanks for both teaching me that the K indicates tolerance and to simply |
| The more I read, the more I learn... | So, the parts that were previously replaced on the master inverter board (and slave now that I look |
| Electrical Feedback | What are these "amps" you are throwing up as being measured by the cable company? AS expressed, none |
| Some Tests to Try... | I, too, would suspect one or more faulty capacitors, especially if they're the old types with a wax |
| PSM210-417A-R Power Supply, cannot locate fault. | This PS is from a 32" Prima LCD Tv. I am certain the TV overheated as it was enclosed behind p |
| While you could use a 2 watt in place of it, it would be underrated and it looks more like a 3 watt |
| Samsung HLN467WX/XAA Unique No Power Problem | Hi. First time viewer and poster here at these forums. I hope somebody can help me.
I have a Sams |
| A/V Tech Wanted - NYC/Brooklyn | Looking for QUALIFIED service technician to handle repairs of audio & visual equipment in the Br |
| Thank for reply drone,
Yes i i am capable of changing the IC, how can i determine which one i nee |
| Looks like a typical voltage regulator IC. Without a diagram it would be very hard to determine the |
| akai AM-52 gives no sound at all | Hi, let me first make myself known.
My name is jan and I come from holland, I'm 52 years old and |
| Program Verify Mode
Verification should be performed on the programmed
bits to determine whether t |
| Impossible to determine the cause without actually opening up & testing the unit; in general the |