| Subject | Text |
| Nitrogen Laser Power Supply (ignition coil) | How's it goin, I am trying to design up a high voltage power supply for a nitrogen laser using the c |
| James,
Looking at the protection ckt in question, you've figured out it's operation. It is based on |
|
|
| Yamaha DSP-A780 with residual hum | Have encountered a unit as above with residual hum on all of it's 5 channels in my trade as a techni |
| Any got a wiring diagram for an Philips FA650? | Hello,
To repair my old Audio amplifier I need a wiring diagram. Thanks!
/Johan |
| PHILLIPS TV SPEAKERS | HELLO, To begin with the addition of speakers to a unit has to involve the understanding of the tot |
| PANASONIC TX-2. need HELP!!! | I need The Service Manual for Panasonic TX-2. The TV set is dead and thereis an low frequency noise |
| :D you need to replace the lopt and transistor ,then check the line drive frequency-there is a fault |
| Do you have it switched to the correct speed? Do you have it connected to the correct frequency of s |
| Circuit diagram for Panasonic SC-HT900 | Hi,
Can anyone give me the location where I can find the cuircuit diagram of Panasonic SC-HT900 s |
| Re: light bulb broke off the wires for main display | [quote:9d1879eb2d="Dean"]I have a 1995 RX-V850 Yamaha Stereo Rec. the through the hole light bulb ha |
| Re: oscilloscope | Thanks!
I've already found it, but thanks anyway.
For the future searches(for archive):
That bl |
| The Cap? hummm I only saw those numbers on it? I can send a picture but really its the size of a nic |
| Aiwa Service Manual | Hi!
I have an old Aiwa Audio System model NSX-S22 that need to be repaired, so I'm looking for th |
| Hitachi 36CX39B TV has a black square in the center | Friends,
My 5 year old Hitachi TV has suddenly started showing a black square in the center of |
| For a T.V. use high temperature (105 Degrees C) capacitors. If they are in a high frequency circuit, |
| TV 5.5" Black&White use IC CD5151CP | Hello!
I could help modify the CD5151 IC time base, to change the frequency output pin 26 to 50Hz |
| Soldering help needed., It don't flow right | I’ve made my first DIY PCB, I’m trying to solder Leds into the holes and I’m a complete newbe, I got |
|
|
| re; Mitsubishi | Hi, try inputting a dvd signal into "video input 1" then if you get a picture
it probably is a tun |
| Re: PCB2310 R133 resistor | [quote:c7f9e4e92a="Transanalog"]I don't think R133 is 800 ohm, rather 0.1 ohm. R133 on mine is Brow |
| Electronic designing ,MCU cracking & development,softwar | Welcome to ZhongHaiKaiRui Designing Center! We come from China,We have servered many customers from |
| Re: peugeot radio code | [quote:da7380a6aa="masterskay62"][quote:da7380a6aa="vunjko"]peugeot 206 serial CL0410Z0151554. MOD |
| i also have a mitsubishi TV and........ | it works great until it warms up. audio is not affected but the screen goes black and it appears to |
| Looked at the blue ceramic caps -- only saw two small ones; but, they look ok. Will need to get und |
| I don't know your set. Get a service manual or a circuit diagram and replace all of the filter capac |
| remotes | can anyone help?
what frequency range does a goodmans 257ns television remote control work over?
|
| Reinstall U31.
Disconnect other amp connector J7/MCON12.
Repeat resistance measurements to SAM |
| VCR panasonic is dead, power supply.......... | Panasonics VCR is dead & the problem is on power supply, i have changed the faulty STR, but ther |
| Old CRT televisions - interesting failure report | Hi everyone,
I am new here & thought this might interest readers & its not a help request. |
| Is it Worth to Buy Hp Probook 6460b for Graphic Designing? | Hi! I'm a beginner-level graphic designer and I'm working in the Logo Design agency as an intern gra |
| Clarion CDC635 CD Changer - Need Service Repair Manual | Need Service Repair Manual
Clarion CDC635 CD Changer
6 Disc Changer - Car Audio
635 or 634. |