| Subject | Text |
| Hi there. Well, ok. I have B&K model 445, and a model 467. There is an adapter that i would need |
| Usually those connectors 'come loose' from too much force being brought to bear.
Is there a lead re |
|
|
| Diana needs help about NCS2001 amp | Hello,
Can anyone help me on my little project herein. I'm using an rail-to-rail operational sub-1 |
| Hi!
Sorry, I'm from Hungary, and my English is very bad.
Unfortunetly I have the same problem. M |
| ok so with the board (43) floating, i measured from each pad on that board to ground. some of the m |
| I have an n3250w with a blown chip on my Darfon 4h.B0280.001/CS2. I accidentally bought FSP228-3F01, |
| Thanks 'Guest'
Always suspected d/j's but your suggestion confirmed it.
I have now re-soldered m |
| light bulb broke off the wires for main display | I have a 1995 RX-V850 Yamaha Stereo Rec. the through the hole light bulb that lights up the main dis |
| I need shema | for auto radio cassetofon Renault Philips 22DC229-62P, or need Power supply
I think toshiba. I do |
| Re: Panasonic 27 inch TV CT-27G5CB | [quote:ab90ebd64e="michaelmcm"]If anyone could please shed some light on my problem with
a panasoni |
| First of all... Hello to all the Googlers who have been searching for a solution to the same problem |
| acer AL2416W monitor mostly dead | I wonder if anyone may have encountered this...Press power button (with or w/o signal cable attached |
| need service manual panasonic cd-cm4720f | [color=red:bd5d717da5]hi everybody ,
I need a service manual for a panasonic-matsushita 6 cd chang |
| FOUND: Executech, DigiTech, HoTelephone, Americom manuals | Looks like I posted this in the wrong place first, moderator, please ignore or remove from ther othe |
| [quote:43d940a35c="elektromaniak2010"]Hello
I'm new here. I have a Yakumo TV LCD TV 81J. It has a p |
| Ok, here is an update
Spoke to Tiny £1 per min told me to do a factory reset on the plasma,
|
| [b]Need Help to fixup LCD cable of Acer Travelmate 290E[/b] | Hi, I have Acer travel mate 290E series. I my Lcd screen was not working I have opned it and complet |
|
|
| If memory serves, max. voltage for most three-terminal regulators is 35 volts (7805 min. voltage = 7 |
| MC68HC705B16N OTP programmer | Can somebody out there email me a reliable circuit diagram for a programming tool to write ROM conte |
| AV RECEIVER Yamaha RXV3800 DC PRT:000 | Please help. My reciver shut down after 3 seconds. What i did I check all on th physical level... Al |
| before replacing ic 7064, you should try to put a 10 nf capacitor between pin 4 et 11 of that circui |
| Hitachi LCD TX38D95VC1CAM | Hello,
I just got this old Laptop from my boss who was gonna toss it out cause the thing stopped |
| You gave three options.
I agreed that it could be any of the three.
Personally, I'd start with |
| Hi,
when I disconnect the two power connectors which goes to the PDP, it's still doing the same t |
| OK, so I've got the LSP ( Large Signal Panel I presume ? ) out & I can't find a V50 connector an |
| need pinout for compaq | Hi all
need pinout for compaq or details on wiring or where i can buy new cable.
Have tried all ov |
| Hitachi | It will probably be one of three things:
!. A bad solder joint on the vertical IC601
2. No 9 volt |
| Re: 50" zenith tv convergance issue | [quote:5df3b9f13b="riverdale"]I have a 50" zenith television that i just replaced the hv splitter an |
| part numbers.... | Hi Minnie,
I didn't know about "partstore". Their prices are good. If they are listing |
| Check the flyback capacitor(s), those are usually 5-10 nF polypropylene capacitors connected from th |