| Subject | Text |
| Re: Onkyo TX-SV535 Amp / Remote Speakers NOT Working | [quote:0d4d64b6e9="kayecross"]I can not get the remote speaker button to work on my amp. I have inst |
| 200/300W power amplified speakers | Hi all,
I need help to find out a good complete project for internal amplifier system for speaker f |
|
|
| I have same problem with my tx-ds494. no its not my speakers. or inputs, definately output in "A" sp |
| phosphor type and deflection yoke assembly differs
check inductances and judge yourself
if both tv |
| Grtz Mark, Sparky
I have had a careful look at the inside of the VCR and I am puzzled by the He |
| [quote:8834774767="Anonymous"]Per toshiba service manual if it is over heating and you can't find an |
| Toshiba 3787DB - Very low Base / Woofer output | Getting a very low output on the sub woofer, with the sub and the base turned all the way up you can |
| Sony Sa-va 700 | Hi! I am having problems with my system. The right side rear speaker keep turning on and off. I chec |
| hardon karmon 7 channel amplifier, 1 channel very low ?? | hello im curretnly working on a hardon karmon avr 507 7 channel amplifier,
it all works ok apart |
| Your dead TX100 chassis Tv | As well as the good advice given by last poster, check/replace the Polyester/Mylar Capacitors across |
| if it is not recognising dvds but cds are fine it is going to be the laser assembly. if you want the |
| THE OPTICAL BLOCK UNIT IS THE LARGE ASSEMBLY VISIBLE IN THE MIDDLE OF THE SET BEHIND THE STEEL BRACK |
| PHILLIPS TV SPEAKERS | HELLO, To begin with the addition of speakers to a unit has to involve the understanding of the tot |
| Taking apart my Philips DECT 2111S/11 | Hi,
I am trying to take apart my Philips DECT 211 phone, because the speaker has managed to come |
| Re: 50" zenith tv convergance issue | [quote:5df3b9f13b="riverdale"]I have a 50" zenith television that i just replaced the hv splitter an |
| pm me with your email address and i will send you the assembly instructions |
| Aiwa Cassette deck AD-WX828 | Ok guys got this double deck in for repair it only needed a head replacement, on assembly it now doe |
|
|
| I have ordered two FET 2SK2698 and should be here tommorow and will put them in and see how i go. Ye |
| Sony Amp - The woes continue | Andreas,
Try removing every input and output and see what happens, then add them back one by one |
| str-de945 problem | Is the action (or lack thereof) intermittant? If so, it is likely a bad solder joint. The IR sensors |
| SONY STR KSL5 Protect Fault | I have a SONY STR KSL5 home cinema system which after about 5 mins shuts off with the word "PROTECT" |
| led moving sign | hello
i m studying electronic engineering at Turkey.
i want to sell led moving signs. forexample |
| Need advice on fixing a NEC 4210W Plasmasync Monitor | I have a NEC 4210W Plasmasync Monitor (Model PX-42M5A) that has 2 bars, one black, one white, going |
| Here's the parts that I used:
[url=R509 100K Ohm 1W resistor[/url] - got an set on Amazon. I prob |
| yeah! tv still working but, always need to push the reset button in front. otherwise no signal with |
| repairing an old sansui amplifier | hello every one ,
new member here and also newby in the electronic repair
i have an old sansui |
| HP LJ4L Gear | No, Gear is part of main motor assembly and is not available separately.
Try The Printer Works fo |
| Onkyo DV-C601 "no disc" problem | I copied this information from another website discussion board. I hope it helps.
I too had the |
| Re; Checking "lenses" | I presume you mean the Laser.
All CD / DVD units have one (sometimes two) laser assembly. Generally |
| Dead Black Diamond BD28WS | Hello to everyone this is my first post here. I have a BD28WS Black Diamond TV. The fault is when I |