| Subject | Text |
| Hitachi C28WF560N frame fault | Hi to you all..
can you help??i have a Hitachi c28wf560n. 11AK45 doard.
Frame fault .picture fold |
| Bush TV frame collapse | Bush2867NTX TV Frame collapse - white horizontal line across middle
of screen. Been suggested check |
|
|
| Have you 200V for video stage ?
- 45V - frame Ic ? |
| I'm lucky that repair and maintain wide variety of equipment including pneumatics - I also get to w |
| Toshiba 42HL167 LCD TV creates colours which are lively and realistic. The thin, black, glossy frame |
| OK, I figured it out-turns out I was using junk tape without frame markers, and it aborted when they |
| hitachi problems switching off | a message to all you people with these problems with your hitachi tvs take the back off you set chec |
| Hi! It's probably the IC of frame. It might be lack of power or
might be broken down, You should |
| Methods of repair? | [quote:c562fb1c5c="jts1957"]Mine is into it's third year. I use at least as heavily as you, cross fi |
| poor soldering on frame ic would usually cause set to shut down with error code of 13, and picture w |
| HI!
You should check the stage of frame ( the coils, electrolyt cap. IC)
If you haven't due skills |
| mitsubishi b dia. model md2856b/11ak45 | frame o/p chip failure & 11 v supply r614 o/c.
repeated failure although no obvious component f |
| Check for supply voltages to the Frame IC. If you don't have a schematic, look up the data sheet fo |
| If anyone has issues with the flex connectors adhering to the edges of the LCD screen itself, there |
| Horiz output | Ahh I get it now,
I would like to scope the base signal while lamp load is on and measure frequency |
| Usually bad soldered joints, we 'call dry joints' that are dull Grey looking with cracks around the |
| Well, I rushed here to post about my latest "progress report" of torturing the A board jus |
|
|
| MATSUI 32WN20 | HEY WONDERING IF ANYONE CAN GIVE ME SOME ADVISE. NOT SURE IF IT'S A FRAME COLLAPSE, BUT MY TV CUTS O |
| Half Screen | I think the monitor is made by KDS and noticed the nanual is available from this site. Just type in |
| Yes, its a CRT and i think your right, i have gone checking the horizontal circuits and they work, i |
| No screws on LCD monitor...how do i open it up? | Hello, I have a 22" Acer LCD screen that I bought to use as a digital picture frame. I had a cu |
| Re: JVC AV-28W going into standby mode automatically | [quote:80c97ef9a6="stormme66"]Hi all,
I have a JVC AV-28WFR1EKS which is sick! After being turned |
| vestel 11ak45 | :( :( 11ak45 stuck in sby any ideas changed loptx opto frame chip psu thanks ph |
| Intermittent loss of picture | Check to see if the CRT filament is still present when you loose the picture, if it's missing resold |
| Yes you are right, it does not say on the videocover but this may be your problem. If you have tv in |
| hi, the problem with your frame is a simple resistor failure it is hard to explain which one it is b |
| Monitor KFC CB1516CL dead power | I have a problem with power block. It have UC3842 but with many back connections. I need a manual or |
| Hi !
Have you checked electrolyt capacitors in Power Supply and
frame stage? Try. |
| envision 7100-e lcd monitor | I dont have the answer to your question.
I do have my own - how do you open the frame?
After re |
| monitor prob | The flashing usually means an error code depending on how many flashes and pauses I dont know this p |