| Subject | Text |
| GDM1950 | I designed a little circuit that changes the horisontal and vertical pulses to the right modes regar |
| It sounds like a crook solder joint in the verticle section of the circuit board. Not too hard to fi |
|
|
| NEC Multisync FP950 or FP1350 schematic needed | After some sparks (I heard), the image has gone, now just the front led is on :(
Where can I find |
| TV thomson ICC11 (63DF89L) shut down itself during few sec. | My TV thomson ICC11 (63DF89L) shut down itself brusquely, the red LED on front panel also led switch |
| Re: Akai CT-T21N32S TV. | [quote:bc2207fab4="burg_69"]Hi All,
I have an Akai CT-T21N32S which will not fire up, the red LED |
| Sony SLV-SE820G VCR | UK Model - Fault no front display and wrong functions on front buttons - I have replaced C701 and re |
| updated | Hi
I have updated with nwe software , but its remain the same , after detecting new programs , goi |
| My money's on cold soilder joint in the vertical circuit as well. Here is what I would advise. Trac |
| Re: TV freezes on channels, can't change | [quote:1b92f2ebef="sweete958"]I have a 32" Magnavox TV set that has lately been freezing up, not al |
| shorted output | Hi, the blinking led on the front panel is telling you that you have a short
in thee amp, the bulge |
| Audiolab and TAG McLaren identical? | I've got an Audiolab 8000S and a TAG McLaren 60iRV. The remotes are interchangeable and differ only |
| Re: Please help : My Panasonic television isn't well at all! | [quote:a0ee332b43="ArthurLee"]About 3 weeks ago, my Panasonic TV started to switch to standby mode q |
| I agree with Mel. This sounds like an x ray protection circu | I agree with Mel. This sounds like an x ray protection circuit that is killing your set when it is a |
| [quote:8f6aaec432="."]Atom: I think trinitrons are still the only real flat crt's. The others I see |
| I removed the main board tonight. Was able to get a good look at all the components and access the |
| How is the set stuck in standby? Are there any sounds coming from the back of the TV when you switch |
| Centrifuge Heraeus Labofuge 200 | Hi, I need an electronic circuit schematic for the Heraeus Labofuge 200 centrifuge. Can send me to m |
|
|
| PEACOCK ENTRADA 19 HELP ME!!!! | [b:60333f1412]Can someone help me? I need printed circuit or service manual of monitor Peacock Entra |
| Re: AIWA CX 51 | [quote:eaae9053ee="Raccoon_Pt"][quote:eaae9053ee="MANUEL"]Hola, he comprado una cadena aiwa cx51e y |
| No screws on LCD monitor...how do i open it up? | Hello, I have a 22" Acer LCD screen that I bought to use as a digital picture frame. I had a cu |
| Yamaha RX-V520 Main Speaker not turning on | Hi,
I have a Yamaha RX-V520 A/V receiver which up until recently worked fine. About a month ago o |
| Trace Elliot Commando 1001 will trade for it | i need a circuit diagram for a Trace elliot 1001 commando bass amp i can trade from a large database |
| Panasonic CT32G32V | Does anyone have schematics for this set.
Especially Degauss circuit/components
Degauss ciol p |
| MC68HC705B16N OTP programmer | Can somebody out there email me a reliable circuit diagram for a programming tool to write ROM conte |
| convergence | Have you adjusted the tubes in the back? You can make adjustments easily. In the front there are f |
| these are tiny "push" type switches that must be soldered onto the front panel circuit board. Easil |
| Re: Just fixed my first photocopier | Clean the fixdrum whit oil...
[quote:68afd613d1="absorbentgnome"]Got a Sharp SF-7300 out of a |
| Replacing a power supply... | ...consumer electronics product: Audiologic color tv/cd/radio portable unit. I burned the power supp |
| Could be short circuit at regulator output, try to disconnect power amplifier then turn it on again, |
| service manual for a pioneer KEH-P6800R (car radio) | I am looking for a service manual for a car radio. The KEH-P6800R. The backlight of the frontpanel i |