| Subject | Text |
| tv picture vanishes | hi. i have a 29 inch mitsubishi tv that is about 8 years old. recently it has started playing up by |
| [quote:87b9f31b94="chappers"]Can also be due to firmware flash gone wrong. Do you have on-screen dis |
|
|
| Re: LG Studioworks 700S 17" CRT Monitor - b&w colou | [quote:d3301e549f="mohhingman"]Hi All,
Here is a tip for a LG Studioworks 700S 17" CRT Monit |
| Electronics parts for TV VCR AUDIO closing down | I HAVE CLOSED MY TV REPAIR BUSINESS AND AM SELLING ALL MY SPARE PARTS, MANUALS(200), VCR & AUDIO |
| Service Manuals For Sale | Need Manuals? I have over 1,200 Factory Service Manuals on Ebay in my Store for Sale.Buy 4 or more a |
| Microwave | If you heard a "POP" and now a loud buzzing noise, it's one of 3 things
1) the rectifier diode on |
| My Tv is at the service and repairs (small local place) and they have contacted aking for any circui |
| outsource repair work | Qualified dvdr, mp3 player, Philips Pronto repair tech looking for repair jobs after work to repair |
| Toshiba FC22 Copier Problem | We have a problem on our hands and I need some help.
First of all, let me say, I'm not a copier r |
| 37lg3000 | Can anyone help with the sourcing of the above screen found one at local tip with a crack in it. Its |
| Here's a thought, use the ones you have untill you get the correct ones. Don't put back 10 volts rep |
| There is no problem using radial mount. As far as the short legs, you need to have a small tip sold |
| Re: 60 inch Zenith projection tv starting to blurr out, Fix | [quote:a37d602a74="RJ"]Nine year old 60 inch projecton tv starting to blurr out. Better to fix or g |
| Introduction and Amp Problem | Let me first introduce myself. I've just graduated from The University of Western Ontario with a BE |
| Hi Mariuss,
I've had a 717 since they launched it back in 2001, and though it's a little tatty now, |
| hissing noises and shutoff | Hi,
I have a 36' inch tv made by rca even though it was under a sears brand the tv makes a loud h |
| Hi absorbentgnome
I found the standby problem, it was CP48. I noticed a lot of AC after the diode |
|
|
| I have one of these, and it is broken! | I just acquired one a Hitachi model 50ux58b from a friend that was going to put it out for trash pic |
| re; vertical | Hi, you have bad electrolytic caps in the vertical circuit, usually
replacing ALL the defective one |
| RCA | The most obvious answer is a blown fuse. If it isn't a blown fuse, it is probably a defective semic |
| Thank you vtech for taking the time to clarify this. If I knew a local tech that I trusted (and assu |
| soldering iron become black | I have a 25watt weller soldering iron and whenever i am about to solder i always clean the tip but i |
| TOSHIBA CX2886/CX2885C | Thankyou very much for the guidance/tips. According to your tips i have checked/changed the suspecte |
| Help!!! Ford car radio ESRT22DPS | I have problem with my Ford car radio mod.no. ESRT22DPS!
Tape works Normally but radio doesn`t work |
| wiring diagram | can anyone please tell me where to find a wiring diagram for the bose stereo in my audi 200 quattro? |
| A repository for Radio Shack schematics in addition RS site? | I'm looking for a schematic for a duofone 202 , phone / memory dialer
The Radio Shack p/n is 43- |
| Hi mAte i think i need this program as well and i have found a site that. Sells the programers but w |
| I'm starting a technical support line on my new toll free | phone number if that's ok with the forum otherwise I'll remove it.
(866) 563-8576 for tech support |
| More than likely the problem is with vertical circuit & dried up/leaky capacitors/ cold solder j |
| Came across these tips for FL1.10 chassis;
[quote:c70eda226f]
Picture height cannot be adjusted |