Subject | Text |
cable lead for Technics ST-HD50 with a Compact disk Player | Dear all,
I have, in vain, been looking for a cable lead for Technics but could not find one.
|
| I don't habve any specific IC to recommend.
But check out
http://www.electronics.ca/reports/mu |
|
Unusual request. | Greetings All:
Am trying to repair a Bosch AL60 DV2425 Battery Charger. Upon closer inspection th |
| Thanks for your reply, I have checkd for dry joints, and connections, and it's still the same.:(
I |
| :D you need to remove the shield on the bottom of the tuner section. if you still have the broken rf |
| Hi G Money..
Are you conected to the correct terminal on the P.C.?? (Preferably "Line Out?")..If |
NAD 317 service manual or schematics wanted | Any one has a copy or a lead as to where I might find one?
Damn, I'll even pay!
Thanks,
Jef |
caution wit this procedure | If your battery is still holding 30min, do not replace it, yet.
If you can't find an exactly same o |
| Thanks for the warning mark.
You are correct that this did lead me to a good path...perhaps the l |
Intercom buzz | Lots of faults can cause buzz, but no ground or poor or corroded ground connections on shields is a |
Thanks! | Hi there,
Just a quick post to thank everyone in this thread for the solution to the RX-V650 powe |
HUGE sigh of relief ! | I was bordering on bummed out, :? hoping there was nothing wrong with my monsters.. I will defi |
No Sound from Onkyo | This is a signal tracing task. Signal tracing is the most basic trouble shooting technique after si |
| what is lead dress ? flux residue? |
Toshiba SD-V291 VCR/DVD combo ejects tape immed after load | Hi. Above noted machine loads tape, but then imediately ejects the tape. I removed the cover and t |
av input | First try a different scart lead, then check for dry joints or cracks around the connecting pins of |
Re: Proview BM568 VGA Cable Pin Outs | [quote:6133c70609="HT"]Hi,
I have a Proview BM568, but the VGA connector needs to be replace. Doe |
|
| I agree with Miguel. if your mixer has PAN controls just turn all of them to the same end so your ch |
| I usually just take a magic marker and draw a line across the control - that is across the movable p |
Old Rank arean stereo similcast video recorder DIN plug conf | Can anyone please tell me the wiring diagram for the DIN plug out of a Rank Arena Video reorder to R |
jd75125 addendum PVY4665RK | :) Sorry Larry E, I did not provide much info. after taking more detailed
look at TV, here are wha |
soldering always getting a dull finish, dry ? | hi,
i bought a soldering atation and doing a bit of soldering work on a curcuit board,\
howeve |
Base station | Just re reading your post.
The base station will not only charge the handset but also picks up th |
| turning it off and back on clears this up?
sounds like it may be a DCU problem (digital convergence |
cd changer leads | Hi everyone,
Can anyone help with a wiring schematic for a cd changer lead from a renault scenic |
Fujitsu plasma SOT ID | I have a PDP driver board and I need to ID 2 components They are a SOT case with 3 lead on one side |
| Testing the circuit is to be done with the power off!!
Do not apply power until you are sure you ha |
| I would check the high voltage block, it is common in rca projections that this part goes down....it |
| If sound was Not a problem BEFORE the convergence repair ... I would suspect lead dress. :arrow: I |
Re: Samsung Syncmaster 711MP LCD TV Monitor -Not Powering Up | [quote:e8914f791a="Anonymous"]I had Same problem. - Now Repaired -
Three of the Five Electrolyt |