| Subject | Text |
| Re: looking for | [quote:6e09f5f793="jts1957"]That's the "Location" and "Rating/Value" of [b:6e09f |
| Being a switchmode powersupply I would not run it without a load otherwise it may self destruct. Plu |
|
|
| TV with black, jumping lines which stretch the image. | Hey all!
I've got a question about my good ol' 28" Sharp TV (28HW 53E). It's getting quite o |
| thanks for the reply. I looked at the electrolytic caps again and only one seems to have some minor |
| No, there's no E-W distortion...this is a plasma tv |
| Yikes! Now it's getting complicated! I found the Power Transistors and ordered them through
htt |
| Re: Viewsonic N3245W Black Screen - Need some help | I would like your old inverter board; have one with bad transformer on; can't find supply of board o |
| [quote:93e26ac61b="vtech"]Depends on your Amplifier drive capability; while it is not too far off, |
| The screens were supposed to be FLAT since the very begginings of the TV (including those B/W ones), |
| Samsung TV (SP42W5HFX/XEU) - Convergence Problem | Anyone with any advice on how to fix convergence problem on a SP42W5HFX/XEU rear projector tv?
C |
| Factory reset default SANYO ce28 wn5 b | Thanks Paul justmanuals. It worked. Is there a factory reset code for this model? Pincusion distorti |
| Bush ws6671sil - 11AK19Pro chassis - Help needed! | Hello!
First off, this site is probably the most useful electronic repair site I have come across. |
| videocon microwave | Worth checking them anyway using a meter as they cause a lot of problems on all microwaves. |
| It sounds like it could be a capacitor related problem. Do you have an ESR meter to test them with? |
| Philips 20PT6441/37 Vertical framing out of whack! | I have a philips 20PT6441/37 that has a verticle framing problem. The top 3-4 inches of the screen i |
| Sharp DA-50W chassis, problem with horizontal output stage | Horizontal output transistor Q601, BUH515 was shorted and resistor RA611 showed signs of overheating |
| Before that,
SYMPTOM: Distorted or no picture
SOLUTION: In order to determine whether picture prob |
|
|
| Hello
You must meter output lines of power supply unit and check that their values being true (as s |
| the best procedure to check ultra fast diode by analogmeter | the best procedure to check ultra fast diode by analogmeter
what is the best procedure?
how t |
| There's no bulging caps that I can see on any of the boards, including the power supply.
So, I sh |
| World's Largest Web Based RFID Training Portal Teamrfid.com | RFID4U brings World's largest RFID eLearning portal TEAMRFID.COM enables learners to grasp these new |
| Can you be more specific about your application? Exactly what are you trying to drive?
Whilst mo |
| PSU problem Infocus 5700 - heat up caps works | Hi all, I have an Infocus Screenplay 5700 projector with a PSU problem. It fails to startup unless I |
| Is it an Electrolytic ? If yes a esr meter, and or a capacitance meter. |
| Nd Svc Manuals - Fluke 8060A, Pana-KX-P4430laser | I looked here far and wide and have not found the manuals.
The KX-P 4430 is similar to several m |
| THE AMP FROM HELL | HELLO, Well this sounds like a big no sound problem. Yes the IC's commonly refered to as the finals |
| Tektronix TDS3032 | Hi everyone,
I have a slight problem with my Tektronix TDS3032 which I'm hoping someone here may |
| sorry that link sucked
here is a working link to a picture of the model number and make and a p |
| In my dealings with satellite receivers if they’re junk you replace them. You can take an esr meter |
| It sounds like some filter capacitors have dried out and need replacing. The blown fuse means there |