| Subject | Text |
| Bad driver or PDP. |
| 42WS90E | Hello,
The Thomson Plasma 42WS90E is actually an NEC rebadged, and yes this is 100% correct the p |
|
|
| [quote:458f746099="gary"]probably a faulty pdp, have a very close look at the screen, check for any |
| Read this 5 plus time, sounds like a bad panel/pdp. |
| Dead Screen on LG Plasma TV | Hi,
I guess my earlier post fell thru the cracks, but if anyone has any idea how I might fix this |
| Hi,
These are out of warranty repairs, the PDP,s are fine as I have tested them with working cards, |
| [quote:9606989fee="minnie"]If your VSC is low/incorrect that would indicate a bad sustain board. [/q |
| the resistors and diode are failing due to the panel drive ics being sc, as these are part of the ri |
| Sure the model of the tv is Phililps 42PF9966/37 the display in the tv is a Samsung PDP S42AX-Xb01 |
| Re: 50MP1 | I have acquired 4 NEC 50 MP1 for free. They all pretty much have the same problem. They will displ |
| corecode is right. | I just ordered pdp 433pe service manual from justmanuals and it doesn't include arp3112 what i need |
| 50MP1 Flashing LED | deejayess:-
1) Power off the unit (using power switch on underside of product)
2) Press & ho |
| pioneer plasma with no picture | I have a Pioneer pdp 436pu (4360HD) that is run by a Pioneer PDP-RO6U media receiver
Problem is no |
| My flat monitor has died | I have verified the all supply card complex and it is not a problem in the supply system. The protec |
| NEC plasmasync 4210W | NEC Plasmasync 4210W
Hello Steve,
Well I drug it out off the closet after 2 years and it still d |
| Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| never had a buffer board fail on that model, have changed 32 of the pdps used in that series of plas |
|
|
| I have been looking over this unit more today, and eveywhere I look LG stickers and part numbers kee |
| Problem with LG MZ-42PZ24 | hello,
i have a problem with my Plasma TV LG MZ-42PZ24, when you turn it on, it turns emmideatly |
| Service Manuals | All,
The service manuals do not include and schematics for the PSU or the PDP module PCB's.
Mi |
| Samsung power supply PS-507-PHN or LJ41-05253A or LJ92-01513 | Please,I need the schematic or service manual for this power supply. Its has a protection module tha |
| Vision / Orion PM-4230 Service Manual? | Has anyone got a copy of the service manual for a Vision PM-4230 Plasma TV, this is the same TV as t |
| Would you mind elaborating a little bit more?
When you say "bad panel/pdp", are referri |
| Thx anyhow, yes i followed the flowchart religiously and all the supplies are present (3.3,5,60 and |
| These are board level repairs as far as Toshiba is concerned. If you have two bad sustain boards I p |
| POWER BOARD | Hello is it possible to send me the schema of Samsung LJ44-00068A PS-423-SD, i am a problem with my |
| NEC PX-42VM3A-PDP module failure | Hello Bob,
Were you successful in aquiring the service manula for this system and might you know |
| When I turn the tv on the 2 power on relays come on then a few seconds later the they turn off ( po |
| PX-42MA | Hi jean974,
Do you know which version you are looking for :-
PX-42VM1A
PX-42VM2A
PX-42VM3A
|
| NEC 50 MP1 | I am looking for a replacement secondhand pdp scan board. Its the large board on the left hand side |