| Subject | Text |
| 98 Civic incremental mech. rotary encoder | 5 pin 2 anchor pins. ALPS JAPAN b/of (pot) VR 401 embossed on board. ON/OFF mometary cks ok. Before |
| Hi, mbelec, | Hi, mbelec,
thanks for your reply...
Where would I see this error code ?
On the PC screen I ass |
|
|
| Just looked at the schematic & sure enough, it is not inclusive with it's electronics(it is a se |
| plastic pulley pt no is vdp1434 but would give error codes F03 or F04 on k mech machines |
| Could I receive a copy, too? Thanks! | Just wondering if you'd mind sending a repair manual my way, too. Won't open and I've got the Mech |
| spindle motors in panasonic dvd players fail frequently, check the resistance out of circuit should |
| [quote:b54fb7477b="vtech"]Not familiar with the specific unit, some mechanism loop basics to check |
| Luxman cd player D-102 service manual needed | Hey there.
I have a Luxman Cd Player D-102 I desperately need a service manual for. The unit had |
| Re: Just fixed my first photocopier | Clean the fixdrum whit oil...
[quote:68afd613d1="absorbentgnome"]Got a Sharp SF-7300 out of a |
| ud-m50 trays | if "Ibbotsnm" wouldn't mind, I'd like a copy of the repair manual for this one?
I have |
| TAKE THE LID OFF THE SET, WHEN THE TRAY CLOSES YOU WILL BE ABLE TO SEE THE DISC IN THE MECH, I USUAL |
| Denon volume control problem | Hi there, my first post.
My son has a Denon UDM3 mini system which has two faults. The CD mech is |
| the mechs in that model are horrendous to set up, i was told once that denon actually withdrew them |
| (72783471 is the correct number for mechanism--only)
wait a sec;
Most manufacturers sell their D |
| THIS MAY SOUND DAFT BUT THE FAULT IS THE RAM DRIVE UNIT ITSELF, IE THE MECH. THE ONLY CURE IS TO REP |
| Service Bulletin | Be aware, repairers, there is a bulletin for this product, to address a common CD fault resulting in |
| Thank you,
Would it be simple job to replace the whole transport, if one could be found? I think |
|
|
| [quote:de9580d3ee]NIGHTMARE TO FIT THOUGH!!!![/quote:de9580d3ee]
I'll bet! I've had the thing apa |
| Denon UD-M50 CD tray | Garry,
I once experienced the same problem with my system. It occurred after I had disassembled |
| Just fixed my first photocopier | Got a Sharp SF-7300 out of a skip, which was absolutely knackered so thought I might as well learn h |
| I FIXED IT | I never did get that repair manual but here's what I did:
Originally, I had loaded 3 CDs (I thoug |
| Panasonic VCR Message F04 | First of all with the cover removed the start/end sensors may be picking up artificial light upsetti |
| Skipping CD Changer, Likely Cause? | Skipping CD Changer, Likely Cause?
I have a Denon micro system with a three CD multi changer that |
| Denon UD-M50 CD Changer problem | Hi our Denon UD-M50 is playing up, just the CD changer. Having taken it apart slide 2 is at the bot |
| If it's the one I'm thinkin of.....That Orion design was probably the cheapest load of crap I've eve |
| denon udm3 | cp 1003 is located under cd mech/can be replaced on pc side tosave removing pcb |
| Strictly working of my memory;---one of the better & rare SACD player you have there.
I used t |
| Misadventure | [quote:42a9058b07="gary"] NOT AN EASY MECH TO RESET, SEND ME YOUR EMAIL ADDRESS AND I WILL SEND YOU |
| Cheers Gary. It's a UD-M5, the one which unfortunatly has the CD mech at the bottom! :0( |
| You mean DVRS150 . Used to see them. Based on your description, it needs the dvd mechanism replaced |