Subject | Text |
| check the pico fuses on the power/deflection board. they may have opened up. |
| Is f883 open? It's a pico fuse. |
|
Hitachi Problem | I have the exact problem with my Hitachi. Two green lights come on, then the third and all fails. |
Re: Convergence IC guide | [quote:c2f4b2bed1="minnie"]It seems that counterfeit convergence IC’s are hitting the market again. |
HP LCD Monitor 1530 Green pwr light no Display | I just recently had the same problem with this monitor.
But after finding this post im back up and |
| you need to check the 2 3.5 amp pico fuses and also check all 3.9 ohm resistors around ics. replace |
| pico fuses go open because faulty ics.not sure location number.check for open pico fuses or 1.0 ohm |
HP1530 monitor no display | When I see some of the solutions suggested for no display problem on HP1530 monitor life changing pi |
Convergence IC's | It seems that counterfeit convergence IC’s are hitting the market again.
STK392-020 can be replaced |
AKAI convergence problem | I think I too am having a convergence problem. I have a 4 year old AKAI PT5598HDI with the bow-tie |
| Check the pico fuses in the power supply to see which one blew. |
hi | i think chasing pico fuse on the backlight side of circuit. now is working great! |
hitachi 50ux19k won't turn on | when trying to power on the set makes a click sound and then shut off immed. I read that a 2 amp pic |
| I'm going by memory, Q410 0r 401 at the edge of the left board is your horizontal pulse. Resolder it |
Convergence IC guide | It seems that counterfeit convergence IC’s are hitting the market again.
STK392-020 can be replaced |
| On a further note, I tested e994, e995, and e996 and they all came up with 0.00 on my ohm meter. I |
| Well I replaced C707 (blue cap) and the 2A pico fuse (E994). Set is back in service - still a great |
|
| YOU NEED TO CHANGE 2 CONVERGENCE ICS.STK392-040.AND ALSO CHECK THE 3.9OHM RESISTORS NEARBY AND REPLA |
| Check the pico fuses. What Ic's does it have for convergence? You'll have to get a meter or call for |
Confirmation | minnie,
I just confirmed (2) 5amp pico fuses were blown in the power supply and believe your advi |
| There's a kit, Deflection PWB Repair Kit X480315. It has you replace Q777 the H out, pico E947 and t |
| OK
No idea what was wrong, ALL IS FINE AND WORKS AGAIN!
The problem was one of the pico fuses.
|
| E994 is a 2 amp pico fuse. |
| C707 is Hitachi part #0244211. #AZ00104M is the pico fuse.
http://www.pacparts.com/model.cfm?mf |
| replace 2 convergence ics on d board and check 6 pico fuses.they are mounted on heat sincs near rear |
| ha..good luck finding a schematic for that...
either get a replacemant remote as minnie posted O |
| 2 (or 3) STK392-040's, check your bias resistors right around the ic's, and look for an open I think |
| just replace 2 convergence ics(stk392-040).and check 2 pico fuses and all 3.9 ohm resistors. |
| Put new IC's in again and check F850 and F851 5 amp pico fuses, you may have toasted them if you sol |
| Ok, you took a multimeter and set it to ohms and tested E994. And your positive the pico fuse is goo |