| Subject | Text |
| miele B865 rotary ironer | Hi is there anyone out there familiar with this rotary ironer that can assist with a roller drive pr |
| over heating electric clothes iron. | I repair electric clothes iron and have found out that a particular brand uses a particular componen |
|
|
| Chi Flat Iron Fuse? | My wife has a $100 flat iron and it keeps changing heats on its own. On one of the ceramic pad ther |
| soldering iron become black | I have a 25watt weller soldering iron and whenever i am about to solder i always clean the tip but i |
| solder sucker soldering iron. | YES,
the lead and pcb are burnt, corroded by being a bad connection, solder just runs off it!
Clea |
| 98 Civic incremental mech. rotary encoder | 5 pin 2 anchor pins. ALPS JAPAN b/of (pot) VR 401 embossed on board. ON/OFF mometary cks ok. Before |
| on the small sub board in the psu replace the small electrolytic capacitors as they have fallen in v |
| Infinity TSS-450 5.1 Surround Speaker System..diagnosis help | Hello,
I recently bought this set of speakers at a yardsale...
Infinity TSS-450 5.1 Surround Speak |
| Spectre X46BV-1080p, Vertical lines in the picture | My issue is, yesterday, when I turned on my TV to play some Xbox, there was a slight distortion thro |
| electric scooter voltage question | I have a 4-wheeled electric mobility scooter model HS-890, which runs on two 12-volt gel cell batter |
| No Display on Sony Tuner | If this is all that is wrong then it wouldn't be a big job.
Capacitors are general purpose cheap sp |
| I really don't know to much about recievers but I've allways fixed my own thanks to theese boards. I |
| help with laptop soldering | I have a laptop I tried to replace the DC jack on. The solder I am using is primarily lead and I ha |
| [i:74a0f4b322]"I should remaind that it's a full circle rotating button. Once again i've opened |
| Problem is the wattage of the soldering iron. 25 watts is simply not hot enough . On double-sided p |
| How to protect and safeguard the audio-visual data carrier? | 1. The audio frequency disc
Now the audio carrier most possibly found in the library is the dis |
| Your going to need a soldering iron with a thin tip, .050 solder wick, heat sink compound, and solde |
|
|
| Do you think the top ones (the rotary knobs which you send MIDI CC messages with) are likely to be e |
| Larger connections and the ones that get hot may have a ring around them from constantly heating and |
| Only put the soldering iron on each cap for a few seconds and obviously remove it before you switch |
| plates loose | Both of my plates are loose from the tip of the iron to almost the base of their attachment site. Is |
| Bush ws6671sil - 11AK19Pro chassis - Help needed! | Hello!
First off, this site is probably the most useful electronic repair site I have come across. |
| Philips 28PW9513 (MD2.22AA) | Hi,
I know this is an old set but it's all I have and can't afford a new one.
I had a problem |
| After plenty of sodding about and trying to correct this. I got my meny back! Wahoo!
All that nee |
| If the brightness has detoriated over the years due to wear of the CRT, then you can restore somewha |
| Hi carnik,
This damage is not so serious,You can change the bad flyback capacitors but to do this n |
| Yes the legs are still intact on the bottom of the capacitor, but there is next to no room to get a |
| Replacing Q330 | You can use a standard soldering iron but make sure it has a fine tip. you will also need some fine |
| Mechanism Service Manual for SONY CCD-TRV 8mm models | I need to find this manual or if someone can tell me how to adjust the rotary head and the reel tens |
| 27PT6441/37 Turn ON | I posted last week that I replaced the Thermistor and the set still had the 3-2-1 code and did not t |