| Subject | Text |
| Philips 29PT9418/79G MG3.1A chassis problem | I wonder if anyone out there can help me with this one, I have recently got an Philips 29PT9418/79G |
| Can anybody translate these into plain english for me? | Hello, the first half of this list was easy to figure out what the settings do. but I can't tell wha |
|
|
| [quote:751411a959="torbjorn"]So, you have identified the RGB signals, that is a good beginning.
The |
| Re: inverter boards for sale | [quote:243bc35474="Dan the TV man"]I have 2 inverter boards-6632L-0283A,6632L-0282A.They areLC370WX1 |
| midas venice 160 | hi guys
i have a midas venice 160 desk ,there main master fader is destorting and there is no ou |
| Service Manual TV Sanyo! | Friends.
I need manual service tv sanyo Mod.:CE 28 SW4 Chassis:PT90 or CM28 SW3TX, both ecran 16/9. |
| Re: [HELP] Panasonic OPTION > PANEL TYPE > OPT 3 bits | [quote:6b106ec95f="Mikii"]Hello. I am looking for a table with the description of the meaning of the |
| here is the color codes:
PIN LABEL FUNCTION COLOR
1 RED Red color signal pink
2 GREEN Green co |
| Re: Schematic LG | [quote:96490d2359="master103"]Check this file:
http://www.eserviceinfo.com/download.php?fileid=15 |
| Sorry to be so long in answering your response to my question. I've been off on other things.
I'm |
| rca proj tv | Thanks for the help... I even got to the adjustments, big mistake went too far on one and lost the m |
| Looking at it again, the C405 got 255V from each end.
Again I don't know much at all on electronic |
| GDM1950 | I designed a little circuit that changes the horisontal and vertical pulses to the right modes regar |
| Sounds like a mistake in buying......
While an oscilloscope can be used to monitor video & si |
| Does the set have this pic in pic module...#930B552..if so suspect bad electrolytic capacitors on t |
| Re: 32AV500U | [quote="JimFraley"]I have this TV with sound and no picture. I tried the flash light trick |
| EASY ADD YOUR SLAVE HDD | Easy, remove the jumper installed on your Seagate hdd, connect the WD on the extreme connector and t |
|
|
| beovision 7 | please help i need the master code for b&o beovision 7 my kid play the remont control thank you |
| references de THT ctv oyko 3716M | TV YOKO
bonjour,
Je suis à la recherche du schéma pour un tél& |
| Int. going to Standby | Hello,
Apart from checking all stabiliser ICs', links (solder top and bottom), etc.and checking for |
| How would i go about getting their service manual? I have already emailed them asking them how to op |
| Re: Orion Studio 710 | Hello
Need schematic for TV Orion Studio 710.
Only horizontal line… I replace V out TDA8174W with |
| JCV LT32x576 Weird Green Pixelated Screen | I've got a broken HD Tv. It's a JVC 32X576. It's a few years old and one day when turning it on the |
| 50mp1 | I have a plasma sync m50p1 out of warranty. when I turn it on I only get a bleeding screen in the mi |
| Which board? | So I have the correct voltages coming from my power supply board. I have the dark picture that I can |
| code for nav + magnetti marelli alfa romeo | Hi !
Could you help me having a master code for my gps nav+ magnetti marelli for alfa romeo 147/g |
| Re: vertical Line | [quote="kmarm"]I have a Sanyo TV MOD. DS31590 it has a 1/8 in vertical line in the middle |
| hi i'm try'ing to mod infocus x1 to work with rgb power led. i have timing problems. if i can obtai |
| Epson 5300 Powerlite | Hello,
I am also looking for service manauls for Epson 5300 Powerlite. In my case the the RGB alig |
| Re: VW42L HDTV10A | [quote:877f3a2419="eztv"]I have repaired the master and slave inverters. They are used in Vizio, Phi |