| Subject | Text |
| Onkyo A-809 | This Parts & Service manual can now be purchased for $10.79 and downloaded immediately after pay |
| Old toshiba amp and pre-amp only outputting high freq. | My stereo (old toshiba/aurex components) is only outputting higher frequencies. It doesn't sound muf |
|
|
| service manual for onkyo receiver tx-25 wanted | can anybody help?
Thanks! |
| onkyo TX-DS575X AV Receiver | I also have a TX-DS575X with same problem. It will produce sound for about 10 minutes then cut-out. |
| onkyo A-8037 | What#s your emailadress? |
| two receivers shorted out | Can anyone help with this problem? I had an old JVC receiver hitched up to two sets of speakers -- o |
| Denon UDM3 No sound output | Hi guys, originally the cd tray wouldn't eject, found the fix for that on here thanks very much work |
| Speakers and wiring are good. The distortion is there regardless of input - whether internal (tuner) |
| When you say. "digital setup", remember that music that you listen to, is and always will |
| Cut into CD input for MP3 | Hello, I would like to connect my mp3 player to the ribbon wire connecter from my built in CD player |
| Klipsch Promedia 2.1 Amplifier Schematic Requested | I purchased a Klipsch Promedia 2.1 off ebay without reading the fine print, and one channel of the A |
| I have just had the same problem on my NR609 as Dire Wolf and others have noted: all working fine fo |
| Adcom Motorized Pot. - Help | I have an old Adcom GTP-500 Tuner/Preamp that I dealry love. It still works great. My remote control |
| Check if there is any tape transport problem that causes wrinkling of the lower edge of the tape at |
| denon udm3 | Yep - I have exactly the same problem. CD tray won't eject. No motors
running. All other functions |
| service manual marantz pm710dc | anyone a service manual fot marantz amplifier pm710dc
or sugestion to solve random rateling noise e |
| If the hum disappears completely when turning down the volume control, then the hum source must be b |
|
|
| Re: denon udm3 | [quote:9288a09cb3="guest"]Yep - I have exactly the same problem. CD tray won't eject. No motors
ru |
| Re: HELP stero repair | [quote:2890bb5678="tim in pa"]my first post, thanks for reading. i am repairing my bosses (i know!) |
| teac receiver- protect mode, all output transistors are ok. | like the title says, TEAC AG-V8500, I cant seem to figure out why this receiver is going into protec |
| Which transistor blew? Was it a main output transistor or smaller one in the pre-amp stages? Why did |
| [quote:e6a73c2eac="opal"]Thanks for the Info,
i have to addmit, im not into Musik really, so i dont |
| There could be many things...
I used to work with various Yamaha receivers & to the best of my |
| Add my TX-NR609 to the list | I have the SAME EXACT issue and it happened 2 months ago. I bought it BRAND NEW when it was first av |
| DIY Disasters | This is a common problem with Onkyos. There are about 10 muting transistors located on the preamp bo |
| New "findings" | OK, no one seems to care about this thread, but I'll post my latest thoughts about the red-level iss |
| Help on RPTV Sound | I have a Hitachi 61SWX10B about 3 1/2 years old. Recently the sound has been crackling and gets wors |
| ..did not know it had a mechanical volume control. As kenray suggested, try cleaning it with a clean |
| 120 cycle hum of death! | I'm working on Kyocera receiver that is giving a nasty 120 Hz hum. It plays fine and sounds good onc |
| Rotel RA980BX distortion | At the moment Im unfortunately working without a circuit diagram, but I do have the benefit of one c |