| Subject | Text |
| NEC PX-42VM3A-PDP module failure | Hello Bob,
Were you successful in aquiring the service manula for this system and might you know |
| When I turn the tv on the 2 power on relays come on then a few seconds later the they turn off ( po |
|
|
| Tisztelt Donca Cristian Ur!
Őszintén megmondva a lejátszónak semmi baja nincs |
| PX-42MA | Hi jean974,
Do you know which version you are looking for :-
PX-42VM1A
PX-42VM2A
PX-42VM3A
|
| NEC 50 MP1 | I am looking for a replacement secondhand pdp scan board. Its the large board on the left hand side |
| Need Help - How to test boards in a plasma TV? | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points |
| Fujitsu plasma SOT ID | I have a PDP driver board and I need to ID 2 components They are a SOT case with 3 lead on one side |
| PS42V6 is a plasma tv, fault could be lower scan pcb or connectors to pdp, or a bad pdp |
| Check the resistor on the flat cable from PCB to PDP module. When is resistor broken try change it. |
| goodmans gtv42p | I require a service manual for goodmans gtv42p it uses a samsung S42D-YD05 pdp panel thanks gary |
| Need help with testing TV components | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points to |
| Welcome to plasma's. Seems with x/y disconnected VS and Va are ok indicating a good power supply. Ho |
| NEC RD-317, PX-RC1E | Hello !
I am looking for programming manuals RD-317, lcd remote controller for NEC PDP monitors. |
| Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| LG Flatron MZ-42PZ24-After turning it on,it turns to standby | Hello,
i hope someome can help me with this problem on my LG PDP Plasma TV:
When you turn it o |
| Looking for a couple of Plasma TV boards | I'm trying to fix my plasma and need the following boards to do so:
SDBD 6871QDH067B
YSUS 6871 |
| COPIERS SERVICE MANUAL | I NEED SERVICE MANAUAL SHARP AR-335/336 HELP MY ARGENT |
|
|
| definetly not the z sus board, either the buffer board at the bottom of the pdp or more likely the p |
| Re: NEC RD-317, PX-RC1E | Did you ever find a programming manual? I'm looking for one too. Would appreciate any help. vendor |
| Plasma Screen SONY PFM 42B2E | Hello Everyone,
I was wondering if someone could help me out who has some knowledge on Presentati |
| I also got a problem with PM-4230 Orion Plasma screen (not a TV) . It is called PLAVO (not VISION). |
| [quote:61dd7c8f2c="jon R"]Thx anyhow, yes i followed the flowchart religiously and all the supplies |
| Thanks for the reply gary. That's what I thought and it sucks :( I had another screen that is the sa |
| Sounds like the power supply may be bad. I can't find any info on that model. Contact LG to see wher |
| Re: Another question | [quote:de20e5c1d6="Anonymous"]Sorry to sound dense - but the panel - is that the screen itself (and |
| I have bad experience with this PDP. Usually is bad PDP module |
| Bad PDP. |
| Philips Plasma tv with Samsung PDA | I am have problems locating a manual with circuit diagrams for a plasma Plililps 42 PF9966/37 using |
| RGB/PAL video monitor needed | I'm looking for a PAL or analogue RGB television monitor, similar to the Philips CM11342/05G
Must |
| 50MP1 | Andy, I used to work for NEC and was the European Technical Specialist for Plasma displays. If your |