| Subject | Text |
| Re: Radio code for old Philips | [quote:793fcba929="jashan"]Hi all,
I have an old philips radio cassette that I want to install in |
| need dump for vcr philips vr3260/95 | thanks. |
|
|
| Rover R660 / Philips 22DC349 | I am currently restoring this vehicle and have sourced an original radio/cassette to replace the upg |
| philips 29PT5515/01 random switch to EXT1 | a noise signal is getting through EXT1, making the tv to automatically switch to that channel, back |
| Re: Decode philips peugeot 206 | [quote:6697757c99="yoana"]Hello everyone!
My radio, is asking for unlock code, since a service.
|
| philips 29' schematic diagram | Hi all,
After 10 seconds aproximadetly the TV goes to off, know some body how I can fix this probl |
| There are many IC like this, made by Philips, which are controlled by a 2-wire I2C bus, i think they |
| Missing Colour on Dell D1626HT CRT | As you say most likely dry joints on the blue drive with conductivity of the joint varying with temp |
| Datasheet for LSC430715 Microcontroller | I found that the pinout (with respect to the OSC1, OSC2 and /RESET pins) corresponded to a datasheet |
| Hannspree JT01-32E2-000G - Viewsonic N3252W | Some info on PSU repair.
These power supplies suffer from Dried up capacitors on the secondary si |
| HELP stero repair | my first post, thanks for reading. i am repairing my bosses (i know!)vintage receiver, pioneer sx95 |
| Boundary-scan (JTAG) circuit debugger and flash programmer | TopJTAG Probe -- boundary-scan (JTAG) based simple logic analyzer and circuit debugging software.
|
| Panasonic Rear-Projection PT-51HX40B Power Supply | I received a Panasonic 51" rear projection tv (PT-51HX40B) with a supposed power supply problem |
| Another method is taking a mains transformer from a wall cube, clock radio etc, that has a secondary |
| Re: yamaha mixer em-100 | [quote:fcc44b3ca6="laurier"]build 1976 , looking for a shematic to repair this venerable audio mixer |
| cd player solution required - NO DISC MASSAGE | Hi, In a Philips AZ8051 CD player LASER glows ,focusinig is ok , cd revolves for half or
one turn B |
| Kenwood KDC-75R Repair and Code disable | A friend on a pension has asked me to repair her car CD receiver and disable the code feature so she |
|
|
| LG 17" monitor Studioworks 77i | My LG Studioworks 77i monitor is shutting down after a few hours.
It's mainly when the room temper |
| Check the I601 VERT OUPUT on the DEFLECTION PWB. I have one that the solder joints cracked and Also |
| The tube. G2 sounds ok. Stick a hv probe under the cap of the flyback and see what your voltage is. |
| Yes I still have it.
Suggest doing some voltage measurements around the output IC.---be carefull n |
| Usually, it is difficult to identify small hole mounted diodes with a such simple marking code.
But |
| Re: FSP194-3F01 | [quote:3429b16c18="hacker gnome"]xtech, Where did you find a power supply?
Thanks[/quote:3429b16c18 |
| [quote:98614bd7be="marquo"]Hello,
I will borrow this thread, as I have a similar request. I also |
| I do not agree with Dfarhen, if you do not know what you are doing or do not have a tester for the c |
| In case of electrolytic capacitors in a switched mode power supply, it is more important to make sur |
| Not really. Did you replace all of the electrolytics around the verticle IC? Use quality high tempe |
| Tektronix TDS3032 Goes Faulty! | My Tektronix 3032 DSO has developed a rather annoying fault. Channel 2 works fine and shows no fault |
| More likely, it is a flashover in the CRT from the EHT (anode) supply to the focus or screen grid, a |
| always an electronics'job???? | hello, someone have an idea for me for find a good electronic'factory in the north of the France? sa |