| Subject | Text |
| pioneer plasma with no picture | I have a Pioneer pdp 436pu (4360HD) that is run by a Pioneer PDP-RO6U media receiver
Problem is no |
| My flat monitor has died | I have verified the all supply card complex and it is not a problem in the supply system. The protec |
|
|
| NEC plasmasync 4210W | NEC Plasmasync 4210W
Hello Steve,
Well I drug it out off the closet after 2 years and it still d |
| Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| never had a buffer board fail on that model, have changed 32 of the pdps used in that series of plas |
| I have been looking over this unit more today, and eveywhere I look LG stickers and part numbers kee |
| Problem with LG MZ-42PZ24 | hello,
i have a problem with my Plasma TV LG MZ-42PZ24, when you turn it on, it turns emmideatly |
| Service Manuals | All,
The service manuals do not include and schematics for the PSU or the PDP module PCB's.
Mi |
| Samsung power supply PS-507-PHN or LJ41-05253A or LJ92-01513 | Please,I need the schematic or service manual for this power supply. Its has a protection module tha |
| Vision / Orion PM-4230 Service Manual? | Has anyone got a copy of the service manual for a Vision PM-4230 Plasma TV, this is the same TV as t |
| Would you mind elaborating a little bit more?
When you say "bad panel/pdp", are referri |
| Thx anyhow, yes i followed the flowchart religiously and all the supplies are present (3.3,5,60 and |
| These are board level repairs as far as Toshiba is concerned. If you have two bad sustain boards I p |
| POWER BOARD | Hello is it possible to send me the schema of Samsung LJ44-00068A PS-423-SD, i am a problem with my |
| NEC PX-42VM3A-PDP module failure | Hello Bob,
Were you successful in aquiring the service manula for this system and might you know |
| When I turn the tv on the 2 power on relays come on then a few seconds later the they turn off ( po |
| Jackson Power Supply #607...No Low Voltages.??? | I just got a Jackson Model 607 Power Supply that my Father had in storage.
I plugged it in and foun |
|
|
| PX-42MA | Hi jean974,
Do you know which version you are looking for :-
PX-42VM1A
PX-42VM2A
PX-42VM3A
|
| NEC 50 MP1 | I am looking for a replacement secondhand pdp scan board. Its the large board on the left hand side |
| Need Help - How to test boards in a plasma TV? | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points |
| Re: Hammond Novachord | [quote:57086aec38="jvromans"]Hello,
I such a Owners Manual of the Hammond Novachord Synthesizer mad |
| Fujitsu plasma SOT ID | I have a PDP driver board and I need to ID 2 components They are a SOT case with 3 lead on one side |
| PS42V6 is a plasma tv, fault could be lower scan pcb or connectors to pdp, or a bad pdp |
| Check the resistor on the flat cable from PCB to PDP module. When is resistor broken try change it. |
| goodmans gtv42p | I require a service manual for goodmans gtv42p it uses a samsung S42D-YD05 pdp panel thanks gary |
| Need help with testing TV components | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points to |
| Welcome to plasma's. Seems with x/y disconnected VS and Va are ok indicating a good power supply. Ho |
| NEC RD-317, PX-RC1E | Hello !
I am looking for programming manuals RD-317, lcd remote controller for NEC PDP monitors. |
| Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| LG Flatron MZ-42PZ24-After turning it on,it turns to standby | Hello,
i hope someome can help me with this problem on my LG PDP Plasma TV:
When you turn it o |