| Make | Model | Problem | Solution | Date |
| | | |
| Found: 698
|
| Amstrad | CTV1600 | Field collapse | R709 22k o/c | 14-09-04 |
| Amstrad | CTV1600 | Field collapse | Dry joint pin12 LA7800 timebase chip (12v supply) | 14-09-04 |
| Amstrad | CTV1600 | Frame - no field scan. | R709 ( 22k ) in series with field hold control o/c. | 14-09-04 |
| B & O | 31/63 | Int reverts to st/by | Dry joints on conns between 2 psu pcbs - check elect caps also | 14-09-04 |
| Beko | 116328NX | Blank grey raster with white line at top | R815 22R in 16v supply o/c as C712 4µ7 hi esr also C811 220µ hi esr (16v supply line had risen to 29v) | 14-09-04 |
| Beko | 16228NTX | Dark pic when R/C used & when OSD present | C103 220µ 400v mains smoothing cap | 14-09-04 |
| Beko | 16228NTX | Dead | Dry joints bridge rect | 14-09-04 |
| Beko | 16228NX | Pic & sound disappears soon aft sw on | Sound present if txt selected - C208 470n in if module dry joint | 14-09-04 |
| Beko | 16326NX | Dead/st/by only or partial line coll | C805 330nF 400v dry joints or burnt | 14-09-04 |
| Beko | 16328 | dead | s/c lopt use HR7218 | 14-09-04 |
|
|
| Beko | 16328NTX | Blank raster with EHT present | Dry joints T104 5v reg | 14-09-04 |
| Beko | 16328NX | Blank red raster - sound ok | No volts coll T1205 - R1215 22k 1w on crt base | 14-09-04 |
| Beko | 16328NX | Dead aft LOPTx changed | Micro SDA20563A516 faulty | 14-09-04 |
| Beko | 16328NX | Keeps auto tuning to same chan | R61 27k 2w o/c - feeds 30v zener from 200v supply | 14-09-04 |
| Beko | 16328NX | No front panel control - r/c ok | Child lock on - to remove hold "+" & "-" buttons whilst sw on tv | 14-09-04 |
| Beko | 16328NX | No mono sound | Faulty IF can - pt no BEKO63S140 | 14-09-04 |
| Beko | 16328NX | No pic unless A1 increased, then same again next time sw on | IC501 TDA4680 | 14-09-04 |
| Beko | 16328NX | poor field lin | R717 1M hi res | 14-09-04 |
| Beko | 16628NS | Dead | R105 33k 2w o/c | 14-09-04 |
| Beko | NR28416ND | Bright white raster | No 200v to TDA6108JF vid amp - crack in print by LOPTx ( under plastic cradle) | 14-09-04 |
| Beko | NR28416NDS | Dead aft thunderstorm | IC601 (MC44608P40), T601 (2SK2545) R606/607 (0.47R, 1/2W) in psu replaced | 14-09-04 |
| Beko | NR28416NDS | Dead with LOPTx insulation breakdown | LOPTx Pt no 058834-TR2 | 14-09-04 |
| Bush | 2160NTX | Dead | UC3844 in psu, LOPTr MJF18204 s/c (used BUT12A in lieu) | 14-09-04 |
| Bush | 2160NTX G1000 | Bright raster with sound | No HT to RGBs - R315 10R pin 9 LOPTx o/c | 14-09-04 |
| Bush | 2163NTX | Dead with smoke | R809 0R47 fusible burnt; s/c chopper tfmr | 14-09-04 |
| Bush | 2163NTXA | Int sound | caused by bad joints UL302 coill near TDA2546 on Nicam pcb | 14-09-04 |
| Bush | 2167NTX | Dead | R5 680K 1 watt in PSU start up circuit | 14-09-04 |
| Bush | 2167NTX | Dead - chopper tr BUZ90 s/c | Check 220k & 330k res in psu | 14-09-04 |
| Bush | 2167NTX | Field - only 2" scan across centre, no sound/pic | R25 12k 1W in 33v line o/c | 14-09-04 |
| Bush | 2169NTX | Dead | R5 680k & check chopper tr | 14-09-04 |