| Make | Model | Problem | Solution | Date |
| | | |
| Found: 267
|
| Akai | TV2034 | St/by only with HT only half normal & LED flashing | Stuck in chjld lock mode - disable using handset | 14-09-04 |
| Amstrad | CTV3032N | Manual tuning | press 1 - press TV- press menu and hold it, the first menu is for sound keep the button pressed and the OVERVIEW menu appears
then release and press menu again this will give you a tuning menu, select the preset number then- with the cursor keys move down to tune and when you get the station you want move down to store then press vol + the word stored appears and then press TV | 14-09-04 |
| Amstrad | WSTV3032 | Dead - BU2525 LOPTr s/c | When replaced ran hot with smoke from D01 - EW driver chip STV2145 faulty | 14-09-04 |
| Amstrad | WSTV3032N | Accessing service mode | Enter code 089 | 14-09-04 |
| Amstrad | WSTV3032N | Removing child lock | press in this order P+ P- V+ V- with the round central button on the hand set, then press o.k. this has to be done in a quick shot within 4 secs, then the lock will be cleared . | 14-09-04 |
| B & O | LX5500 3903 | St/by only after initially being hard to turn on | C20 & 25 47µ 50v | 14-09-04 |
| Beko | 20306NX | Dead - MOSFET 2SK1118 s/c | Only works short time aft replacement - chopper tfmr faulty | 14-09-04 |
| Beko | 2030T | Rapid tuning drift | R61 27k 2w | 14-09-04 |
| Beko | 20320 | Field collapse | Replace R734 (1k5), D704 (BA 157). | 14-09-04 |
| Beko | 20320 | No B in txt | C501 10nF on main pcb o/c | 14-09-04 |
|
|
| Beko | 20320NX | Field scan non lin - stretched at top | 220R resistor across scan coils | 14-09-04 |
| Beko | 20320NX | Line tearing at top of pic | 220R resistor across scan coils o/c | 14-09-04 |
| Beko | 20320NX | No Tuning Menu | Reset micro - Press & Hold P+/P- on set & sw on. Set comes on in service mode - then sw off | 14-09-04 |
| Beko | 20320NX | Sound pops when vol adj | IC601 TDA6610-5 | 14-09-04 |
| Beko | 20320T | Field collapse with rainbow effect | replace ESM740 thyristor - new type requires a 47 ohm resistor from gate to source. | 14-09-04 |
| Beko | 30320 | Pic int fades out | Invisible dry joint on LOPTx pin (CRT Htrs) | 14-09-04 |
| Beko | 30328T | St/by only | No line - line dr tr T801 o/c | 14-09-04 |
| Beko | NR30328 | Dead 1.6A fuse shattered | Dead s/c on chopper caused by s/c chopper tfmr | 14-09-04 |
| Beko | NR303281 | Tripping - s/c across LOP | C807 (470pF 2kV) adj to lopt s/c. | 14-09-04 |
| Beon | CTV1403T | No start up | Check/replace R508/9 150k ?w, R107/8 270k ?w, D111 CNX82A opto and wire link from micro to opto coupler driver | 14-09-04 |
| BPL | FMR9403 | Field jitter & lines at bottom of pic | C455 2µ2 50v (pin 2 FOP chip) | 14-09-04 |
| BPL | LMR9403 | Field speed off | C232 3µ3 63v | 14-09-04 |
| BPL | LMR9403 | Lines at bottom | C455 2µ2 50v (pin 2 FOP chip) | 14-09-04 |
| BPL | LMR9403 | No sound | Q511 2SA1015Y & replace R520/521 120k 1/2w, C562 22µ 250v, R562 3R9 1/2w & IC7171 AN5265 | 14-09-04 |
| BPL/Zenor | KLR9403 | Patt & no chan store | Earth on TXT panel o/c from main pcb - resolder | 14-09-04 |
| Bush | 2031 11AK19-5 | Dead with no power led | HT only 60v - dis'd R823 to opto got HT up to 113v but with poor reg - C829 smoothing cap faulty | 14-09-04 |
| Bush | 2720 11AK03 | Uncontrollable brightness & flyback lines. | R901 ( 220 ) on tube base o/c. | 14-09-04 |
| GEC | C2036H PIL | No neons on touch-tune. | IC202 ( SN70769N ) | 14-09-04 |
| GEC | C2290H 2036 Hit | Dull raster may not have any colour. | IC ( TDA3561A ) decoder. | 14-09-04 |
| Goldstar | RC7031 | Critical AGC level adjustment cut off | C707 4.7mfd 50v | 14-09-04 |