| Make | Model | Problem | Solution | Date |
| | | |
| Found: 20
|
| Philips | 14PV263 | Calling installation menu | The installation menu is activated by the following procedure:
- switch on the set by means of the stop key.
- Press simutaneously the cursor left and the cursor right key on the remote control. | 14-09-04 |
| Philips | 14PV263 | Codenumber correction | The codenumber of pos. 1701 (tuner) for 14 inch sets with IEC input is 4822 210 10691 (UV916S). | 14-09-04 |
| Philips | 14PV263 | Codenumber correction | The codenumber for the scanner-motor (POS. 34) in the Service Manual is wrong.
The correct codenumber is 4822 361 215 48. | 14-09-04 |
| Philips | 14PV263 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | 14-09-04 |
| Philips | 14PV263 | Codenumber information | Please add following codenumbers to the Service Manual:
Lift-flap 14PV263/01 : 4822 443 10404
Lift-flap 14PV263/02 : 4822 443 10404
Spring for lift-flap : 4822 492 70896 | 14-09-04 |
| Philips | 14PV263 | Correction service Manual 14PV263/01 | The indication of the small-signal PCB (page 1-3) is wrong. The right indication is PSSPP3/GPVXF.
This PCB is only applied in 14PV263/01. | 14-09-04 |
| Philips | 14PV263 | How to activate/de-activate "Hotel mode" | Activation:
- set volume to desired level.
- select programm 38.
- press the STOP button of the remote control AND the STOP button of the VCR for about 5 seconds, until the message H+ appears.
De-activation:
- set volume to desired level.
- select p | 14-09-04 |
| Philips | 14PV263 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11075.
Key set for: 14PV263/01/02/08/13 - 14PV264/39 - 14PV163/05 - 14PV172/01/05/08/13/39 - 14 | 14-09-04 |
| Philips | 14PV263 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes).
Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | 14-09-04 |
| Philips | 14PV263 | Set produces audible noise in stand-by | Add a small LEBL (leading edge blanking) PCB, to avoid auto oscillation of transformer 5330 (or 5331). A modification letter is included with the lable PCB. This PCB is available with service nr. 4822 214 12173.
Since production week 9723 this circuit is | 14-09-04 |
|
|
| Philips | 14PV263 | Set produces audible noise in stand-by | Add a small LEBL (leading edge blanking) PCB, to avoid auto oscillation of transformer 5330 (or 5331). A modification letter is included with the LEBL PCB.
This PCB is available with service nr. 4822 214 12173. | 14-09-04 |
| Philips | 14PV263 | Spare part information | A repair kit , containing PULLEY SHAFT + WORM SHAFT (POS. 47+48) is delivered with codenumber 4822 310 10657.
This kit can be used for all TURBO- and ECO mechanisms ! | 14-09-04 |
| Philips | 14PV263 | Spare part information | If the lever inside the mains-switch is broken, the switch doesn't remain in the "ON" position.
Solution: replace the switch by a new one. Improved switches of a newer production range are on stock. (4822 276 13542) | 14-09-04 |
| Philips | 14PV263 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front LED starts blinking, but the set doesn't start.
Solution:
Check the primary voltage (Ubat) and adjust this for 14" sets to exactly 101.5 Volt. (See chapter 3.1.1 | 14-09-04 |
| Philips | 14PV263 | Start up problems after replacing TS7352 | When TS7352 is replaced, it can happen that the set doesn't start up properly.
There are 2 possible solutions for this problem:
- use SGS type MTP3055E (4822 130 63726).
- In case of a motorola type MTP3055V (4822 130 60838), add a 22 uH coil soldered | 14-09-04 |
| Philips | 14PV263 | Strange colours after recording. | Check chroma IC7051 (4822 209 90538).
| 14-09-04 |
| Philips | 14PV263/01 | Codenumber information - new software | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01, | 14-09-04 |
| Philips | 14PV263/01 | Option code: 24492 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code !
For early sets without this information on the typesticker, the option code is: 24492 | 14-09-04 |
| Philips | 14PV263/02 | New VPS IC SDA5642-6 (pos. 7840) | Since production week 9741 a new VPS IC pos. 7840 (SDA5642-6) is introduced in production. This IC is not compatible with the previous one. When ordering, look at the printing on the IC !
Old: SDA 5642-5 - codenumber 4822 209 32728
New: SDA 5642-6 - co | 14-09-04 |
| Philips | 14PV263/02 | Option code: 23532 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code !
For early sets without this information on the typesticker, the option code is: 23532 | 14-09-04 |