| Make | Model | Problem | Solution | Date |
| | | |
| Found: 397
|
| Akai | CT2115UK | Lack of width & burning smell | R824 100R 2W overheating due to dry joint L824 | 14-09-04 |
| Akai | CT2115UK | St/by only | PCA84C640P micro | 14-09-04 |
|
|
| Akai | CT2159 Onwa | Field faulty - int lines at top etc | C417 220mfd 16v, C423 2200mfd 25v, C435 470mfd 16v | 14-09-04 |
| Akai | CT2159UT Onwa | No start up | C910 & C912 47µ | 14-09-04 |
| Akai | CT2159VT | Dead | Sw mode tr overheats - replace D901, C405, C910, C912 & C431 | 14-09-04 |
| Akai | CT215UK | Trips off with chirp & no st/by | C817 100µ o/c | 14-09-04 |
| B & O | MX1500 | INT GOES INTO SEEK | MOMENTARY SWITCH NEAR MAINS SWITCH INT SC ( REMOTE CONTACT ) | 14-09-04 |
| B & O | MX1500 | Won't tune | TRANSISTOR 7070 LEAKY BC548 | 14-09-04 |
| B & O | MX1500 78XX | raster but no sound or picture. | ICP1640 ( 630mA ) o/c. | 14-09-04 |
| Beko | 15221NX | Pic fades | D1209 on crt base leaky | 14-09-04 |
| Beko | 15225 | Pic shifted vertically | For up check R717, R722 1M; for down check R725 150k | 14-09-04 |
| Beko | 15225NX | Brightness varies aft LOPTx replacement | R1237 1k2 1w o/c in A1 feed | 14-09-04 |
| Beko | 15225NX | Dead - fuse blows | T101 s/c - replace T101 BUZ90AF & TDA4605 | 14-09-04 |
| Beko | 15225NX | Dead? | D801 BY299 s/c | 14-09-04 |
| Beko | 15225NX | off burning smell | L507 dry joint | 14-09-04 |
| Beko | 15225NX | Pic shifted to bottom | R725 150k hi res | 14-09-04 |
| Beko | 15225NX | Trips at sw on with loud crack | Lopt arcing between A1/Focus controls - replace loptx | 14-09-04 |
| Beko | 15325NK | St/by only s/c line dr tr TR801 BC635 | Due to Field drive int o/p from TEA2029C (faulty?) | 14-09-04 |
| Beko | 15325NX | Balnk raster with white line across top - sound ok | T701 10HM Thy s/c replace with ESM740ST & C123/124 47µ 160v | 14-09-04 |
| Beko | 15325NX | Bright raster & trips to st/by | R1215 22k o/c | 14-09-04 |
| Beko | 15325NX | Dead - psu blown | Sw mode Trfmr pri s/c - replace with correct one for screen size or lack of width E/W faulty | 14-09-04 |
| Beko | 15325NX | No signals | No 30v to tuner - R61 100k o/c, D61 30v zener s/c | 14-09-04 |
|
|
| Bush | 1500 | Brightness excessive with little control | D406 1N4148 o/c | 14-09-04 |
| Bush | 1500 | Off tune & won't stop in search | T101 vis detector coil replaced | 14-09-04 |
| Bush | 1500 | Stuck on 1 chan with no response to R/C | Check front controls & aux contacts on mains sw for leak (Check for black glue) | 14-09-04 |
| Bush | 1500 | Weak, washed out pic - no sync | Q104 2SC1815 | 14-09-04 |
| Bush | 1557NTX | Dead. | ZD402 Zenor , R422 ( 3.3R 2W ) , C909 , 910 ( 47uf ) , Z901 ( 8.2v ) , Z902 , Q904 | 14-09-04 |
| Bush | 1557NTX | If standby selected pic becomes dark & sound mutes | Q907 ( 2SC2335 ) | 14-09-04 |
| Bush | 1557NTX | No sound or raster - HT line Ok. | R919 ( 0.68ohm ) fusible o/c. | 14-09-04 |
| Bush | 1557NTX | White raster with flyback lines. | Check for 12v on ZD402 , if low check D404 & print between D404 & R422 | 14-09-04 |