Make | Model | Problem | Solution | Date |
| | | |
Found: 44
|
Akai | TV2034 | St/by only with HT only half normal & LED flashing | Stuck in chjld lock mode - disable using handset | 14-09-04 |
Beko | 20306NX | Dead - MOSFET 2SK1118 s/c | Only works short time aft replacement - chopper tfmr faulty | 14-09-04 |
Beko | 2030T | Rapid tuning drift | R61 27k 2w | 14-09-04 |
Beko | 20320 | Field collapse | Replace R734 (1k5), D704 (BA 157). | 14-09-04 |
Beko | 20320 | No B in txt | C501 10nF on main pcb o/c | 14-09-04 |
Beko | 20320NX | Field scan non lin - stretched at top | 220R resistor across scan coils | 14-09-04 |
Beko | 20320NX | Line tearing at top of pic | 220R resistor across scan coils o/c | 14-09-04 |
Beko | 20320NX | No Tuning Menu | Reset micro - Press & Hold P+/P- on set & sw on. Set comes on in service mode - then sw off | 14-09-04 |
Beko | 20320NX | Sound pops when vol adj | IC601 TDA6610-5 | 14-09-04 |
Beko | 20320T | Field collapse with rainbow effect | replace ESM740 thyristor - new type requires a 47 ohm resistor from gate to source. | 14-09-04 |
|
Bush | 2031 11AK19-5 | Dead with no power led | HT only 60v - dis'd R823 to opto got HT up to 113v but with poor reg - C829 smoothing cap faulty | 14-09-04 |
GEC | C2036H PIL | No neons on touch-tune. | IC202 ( SN70769N ) | 14-09-04 |
GEC | C2290H 2036 Hit | Dull raster may not have any colour. | IC ( TDA3561A ) decoder. | 14-09-04 |
Goodmans | 2032 | Dead - smoking | C444 330pf 2kv | 14-09-04 |
Goodmans | 2032 | Field - top foldover | C313 2µ2 200v o/c | 14-09-04 |
Grundig | CUC2030 | E/W poor | TDA8350 FOP chip | 14-09-04 |
Grundig | CUC2030 | Hor black & white lines & no tuning | Sound MSP chip faulty - causing corruption to data lines | 14-09-04 |
Grundig | CUC2030 | Hotel mode disabling | Sw set off at main Sw. Press "I" button & Sw on. In service menu change Hotel to "off" | 14-09-04 |
Grundig | CUC2030 | Line collapse | dry joint scan coil plug & R55006 5R6 1/2w o/c causing no E-W | 14-09-04 |
Grundig | CUC2030 | Menu access & child lock | hold the vol+ button on the remote and switch on the tv via
the on/ off switch.this results in the language menu coming up. if you then press ok the set goes straight to auto tune mode. if you then press text this stops auto tune and allows you access to all menus.entering the code 7038 cancels lock? | 14-09-04 |
Grundig | CUC2030 | Parental lock | hold the vol+ button on the remote and switch on the tv via the on/ off switch.this results in the language menu coming up. if you then press ok the set goes straight to auto tune mode. if you then press text this stops auto tune and allows you access to all menus.entering the code 7038 cancels lock | 14-09-04 |
Grundig | CUC2031 | Set jumps from Chan 1 to AV3 int on its own | Check for arcing LOPTx | 14-09-04 |
Grundig | CUC2032 | Dead | BUZ90 SMPS T60006 s/c & fuse SI60001 1.6S o/c - caused by R60001 270k & R60007 120k hi res also TDA4605-3 | 14-09-04 |
ITT | CT2712 CVC1203 | Dead. | MR diode s/c , may have taken tripler. | 14-09-04 |
ITT | CT2712 CVC1203 | No Frame - resistor R522 burnt up. | R522 is a 0.47R , D523 ( BA158 ) , TBA2653A | 14-09-04 |
ITT | CT2712 CVC1203 | No tuner voltage. | R522 is a 0.47R , D523 ( BA158 ) , TBA2653A | 14-09-04 |
ITT | CVC1203 | Lack of width. | T563. | 14-09-04 |
ITT | CVC1203 | Width will not adjust. | T562. | 14-09-04 |
ITT | CVC1203 CT2612 | 10uf C733 blown apart. | Change C703 ( 10u f ) | 14-09-04 |
Matsui | 2038 Onwa | Dead | C909/911 457µ 50v, ZD401 12v zener s/c, R419 5R6 3w hi res | 14-09-04 |