| Make | Model | Problem | Solution | Date |
| | | |
| Found: 88
|
| Bush | 2160NTX | Dead | UC3844 in psu, LOPTr MJF18204 s/c (used BUT12A in lieu) | 14-09-04 |
| Bush | 2160NTX G1000 | Bright raster with sound | No HT to RGBs - R315 10R pin 9 LOPTx o/c | 14-09-04 |
|
|
| Bush | 2163NTX | Dead with smoke | R809 0R47 fusible burnt; s/c chopper tfmr | 14-09-04 |
| Bush | 2163NTXA | Int sound | caused by bad joints UL302 coill near TDA2546 on Nicam pcb | 14-09-04 |
| Bush | 2167NTX | Dead | R5 680K 1 watt in PSU start up circuit | 14-09-04 |
| Bush | 2167NTX | Dead - chopper tr BUZ90 s/c | Check 220k & 330k res in psu | 14-09-04 |
| Bush | 2167NTX | Field - only 2" scan across centre, no sound/pic | R25 12k 1W in 33v line o/c | 14-09-04 |
| Bush | 2169NTX | Dead | R5 680k & check chopper tr | 14-09-04 |
| Bush | 2169NTX | Dead with 2.5A fuse o/c | R1 5R6 o/c, R4 270k o/c, Q1 MOSFET - use BUZ77B in lieu | 14-09-04 |
| Bush | 2169NTX | Dead with mains fuse blackened | Q1 P3NA90 chopper tr s/c, R4 270k & R5 680k could be hi res & check C11 47µ & C12 1µ | 14-09-04 |
| Daewoo | DMQ2166 | HOW TO ENTER IN SERVICE MODE FOR TV Daewoo DMQ 2166? | you need a spesific remote from deawoo | 28-06-05 |
| Goldstar | 2168F | FIELD CRAMP , LINE ACROSS SCREEN | C309 ( TANT ) 0.22mfd | 14-09-04 |
| Goldstar | CIT2162X | Int loss of signals | Tuning vots increases to 31v - bad conn on lead between tuner prescaler & tuning pcb | 14-09-04 |
| Goldstar | CIT2162X | INT low gain or just snow tuning VOLTAGE AT 30v | INT OC IN LEAD FROM PRESCALER TO TUNING PCB | 14-09-04 |
| Goldstar | CIT2162X | Low brightness. | C820 ( 10uF ) | 14-09-04 |
| Goldstar | CIT2162X PC08X8 | Dark - only get pic when A1 at max | 180v to vid stage high at 278v; C401 10µ 160v on 112v rail o/c | 14-09-04 |
| Goldstar | CIT2168 | Dead | LOPTx shorted turns | 14-09-04 |
| Goldstar | CIT2168 | Dead - 118v HT low at 50v | C806S 47µ 160v HT smoothing cap | 14-09-04 |
| Goldstar | CIT2168 | Field collapse - int | Pin 5 TDA1170N was 5v instead of 25v. D301 1N4003 faulty. If chip turns out to be faulty use genuine Goldstar chip (others won't work - allegedly) Also check R320 10R 1w | 14-09-04 |
| Goldstar | CIT2168 | Int start up | D401 1N4003 o/c in line dr supply | 14-09-04 |
| Goldstar | CIT2168 | No start up | Check R811P 22k 3w, D805P R10J in start up cct, C805P 100µ 16v | 14-09-04 |
| Goldstar | CIT2168 | Sound muted & goes to Stby after 10mins. | Replace the TDA1940 IC401 remove the link J8 & fit 1k instead. | 14-09-04 |
|
|
| Goldstar | CIT2168 | Txt absent | Dry joints conn P102 on txt pcb | 14-09-04 |
| Goldstar | CIT2168F | Field foldover | C423, C302 100µ 35v | 14-09-04 |
| Goldstar | CIT2168F CIT2190F etc | No sound - pic ok - sw to st/by aft 10 mins | Pin 7 IC401 TDA1940 produces muting o/p - chip u/s. Fit 1k res in place of J8 link | 14-09-04 |
| Goodmans | 206N/216NS | 1 Pri col missing | R908, 909 or 907 100k on crt base | 14-09-04 |
| Goodmans | 206N/216NS | Black raster - sound ok | CRT faulty - unplug P602 to test, wait until screen lights then refit - shows a dull pic | 14-09-04 |
| Goodmans | 206N/216NS | Dead - F801 blown | IC801 STR5707 reg faulty | 14-09-04 |
| Goodmans | 206N/216NS | Field collapse | C301 s/c, C405 & I301 blown | 14-09-04 |
| Goodmans | 206N/216NS | Line tearing aft 5 mins | Dry joint RC26 , pin 43 of IC501 | 14-09-04 |