| Make | Model | Problem | Solution | Date |
| | | |
| Found: 22
|
| Goodmans | 2576 | E/W faulty | IC18 TDA4950 | 14-09-04 |
| Hitachi | C2576 | Set up mode exit | 1. Ensure service mode is displayed on OSD. 2. Switch to standby. | 14-09-04 |
| Hitachi | C2576TN | St/by only - stuck in prot mode | volts Q958 gate 0.7v = prot mode. Link out C932 to disable. Audio o/p chip IC4500 split & faulty | 14-09-04 |
| Hitachi | C2576TN | St/by only then dead | R95112k hi res, Q903 ON4584 s/c - used BUT18F in lieu, C915 33µ 16v & check for dries * R950 & R952 | 14-09-04 |
| Hitachi | C28300,C2576TN etc A5 chassis | Field lin & lines at top of pic | C725 33nF 400v | 14-09-04 |
| Hitachi | C28300,C2576TN etc A5 chassis | Int trips & lines | C719 4µ7 250v smoothing cap for 200v in E-W corr & check joints T702 (under plastic strut) & R950 68k near HT pot | 14-09-04 |
| Hitachi | C28300,C2576TN etc A5 chassis | Red pic with fb lines | R829 fusible on crt base o/c (not shown on cct diag) | 14-09-04 |
| Sanyo | CBP2576 | Excess width & pin cush dist | L750 & C653 | 14-09-04 |
| Sanyo | CBP2576 | JUST SNOW IN TUNING MODE | CHECK FOR CORRECT CONFIGERATION NUMBER 02014 TO ENTER SERVICE MODE PRESS MEMORY ON CT AND WITHIN 5 SECS PRESS MENU BUTTON ON REMOTE THEN ENTER THE ABOVE NUMBER | 14-09-04 |
| Sanyo | CBP2576 | NO SOUND | REPLACE ICP853 AND IC1680 | 14-09-04 |
|
|
| Sanyo | CBP2576 | Pin cush dist | Replace C750 2.2mfd | 14-09-04 |
| SANYO | CBP2576 | VERY BRIGHT RASTER SOUND OK | CHECK R534 22K OHM | 14-09-04 |
| Sanyo | CBP2576 ED0 | Burning smell then dead | Burn up on pcb at line scan connector K-FF | 14-09-04 |
| Sanyo | CBP2576 ED0 | Dead - whistle only - LOPTr 2SD1556 leaky | ,Overheats when replaced with int narrow pic, replaced C750 47µ 50v & C705 2µ2 50v for hi esr & check for dry joints in LOP section | 14-09-04 |
| Sanyo | CBP2576 ED0 | No E-W correction | ICP R756 (N20) o/c | 14-09-04 |
| Sanyo | CBP2576 ED0 | No sound | Carry out "start NVM" proc as described in manual | 14-09-04 |
| Sanyo | CBP2576A | Field top foldover & excess height | C703 100µ 50v | 14-09-04 |
| Sanyo | CBP2576A ED0 chassis | Height twitches, int bright raster with fb lines | Resolder conns on digital panel | 14-09-04 |
| Sanyo | CBP2576A ED0 chassis | No raster | TEA5101A RGB chip | 14-09-04 |
| Sanyo | CBP2576A/00 | Bright blue raster with fb lines | IC500 which is a TEA5101A on the crt base pcb. R534 22 ohm was ok. | 14-09-04 |
| Sanyo | ED0 CBP2576/2876 | no pic, no sound when entering tuning mode (just snow) | enter service mode and enter correct configuration code 02014 | 14-09-04 |
| Sony | KV2576UB | NO RASTER - FIELD COLLAPSE BUT BLANKED OUT | CHECK RES IN SERIES WITH D804 | 14-09-04 |