| Make | Model | Problem | Solution | Date |
| | | |
| Found: 46
|
| Goodmans | 2580 | Sound missing | TS90 BC848B sm in sound mute stage | 14-09-04 |
| Goodmans | 2580 TX92 | Appears to have field coll with bright line near top | TP91 BC848B & TP96 BC858B sm in psu | 14-09-04 |
| Goodmans | 2580 TX92 | Line tearing aft warm up - bad on Txt | Internal arcing of EHT lead at LOPTx end - make sure of a good contact | 14-09-04 |
| Goodmans | 2580 TX92 | Sound missing | TS90 BC848B sm | 14-09-04 |
| Goodmans | 2580(TX92) | LINE TEARING AFTER SET WARMS UP | CHECK EHT LEAD IS FULLY SLOTTED INTO LOPT | 14-09-04 |
| Goodmans | 2580/2880 TX92 | Dead - tripping Led flashes once per sec | TP22 BC337 in PSU | 14-09-04 |
| Goodmans | 2580/2880 TX92 | Int sound or screeching with pic present | Dry joints IP08 | 14-09-04 |
| Goodmans | 2580/2880 TX92 | No R/C | GM01 has narrow acceptance angle - replace | 14-09-04 |
| Goodmans | 2580/2880 TX92 | No sound | TS90 Tr | 14-09-04 |
| Goodmans | 2580/2880 TX92 | No sound | TS90 sm BC848B | 14-09-04 |
|
|
| Goodmans | 2580/2880 TX92 | St/by only | RP62 2R2 | 14-09-04 |
| Goodmans | 2580A/2880A ICC9 | Field cramp at top - int | DF31 - replace with BA157 | 14-09-04 |
| Goodmans | GD2580 | Loud whistle | LL26 coil in line stage - hot melt glue used | 14-09-04 |
| Goodmans | GD2580 TX92 | E/W settings different at sw on & int reverts to st/by | IF02 STV2145 | 14-09-04 |
| Goodmans | GD2580 TX92 | Int dead | dry joints CP13 1nF5 1.6kv | 14-09-04 |
| Goodmans | GD2580B TX92 | Installation menu entering | Sw TV to st/by then sw off at mains. Sw on TV whilst holding "P" button in on front until Lang menu appears | 14-09-04 |
| Matsui | 2580 | Dead | Check R808 270k & TDA4601 | 14-09-04 |
| Matsui | 2580 | Dead | CHECK R808 270K , TDA4601 | 14-09-04 |
| Matsui | 2580 | Dead - Low HT rail | C808 1mfd OC | 14-09-04 |
| Matsui | 2580 | DEAD BUT STANDBY LED ON | CHECK HT , IF LOW C808 1uF , 63V | 14-09-04 |
| Matsui | 2580 | Dead or int goes to st/by | Check 145v HT at at scan coil interlock, if missing check link between L805 & R826 for poor joints - also check fuseholder for tightness | 14-09-04 |
| Matsui | 2580 | DEAD STBY LIGHT ON | HT LOW AT 70v IF ON BUTTON HELD IN HT VARIES FROM 70v - 100v C808 1uF 63v | 14-09-04 |
| Matsui | 2580 | DULL RED ON SCREEN WITH RED FLYBACK LINES IN ONLY | IC101 ( VCU2133 ) | 14-09-04 |
| Matsui | 2580 | Dull red raster with fb lines | IC101 VCU2133 | 14-09-04 |
| Matsui | 2580 | FIELD COLLAPSE | CHECK PIN 2 TDA8175 FOR 24v PIN 7 FOR 2.5v DRIVE IF OK REPLACE IC | 14-09-04 |
| Matsui | 2580 | Height variations until heated | Check 24v supply - D804 ZPY is prone | 14-09-04 |
| Matsui | 2580 | HEIGHT VARIES | D804 IN 24v SUPPLY | 14-09-04 |
| Matsui | 2580 | HEIGHT VARIES DURING WARMUP | D804 ZPY24 | 14-09-04 |
| Matsui | 2580 | INT WON'T COME OUT OF STBY | D118 INT OC | 14-09-04 |
| Matsui | 2580 | No E-W corr | Dry joint E-W mod diodes & L901 coil had overheated | 14-09-04 |