Make | Model | Problem | Solution | Date |
| | | |
Found: 26
|
Amstrad | CTV3032N | Manual tuning | press 1 - press TV- press menu and hold it, the first menu is for sound keep the button pressed and the OVERVIEW menu appears
then release and press menu again this will give you a tuning menu, select the preset number then- with the cursor keys move down to tune and when you get the station you want move down to store then press vol + the word stored appears and then press TV | 14-09-04 |
Amstrad | WSTV3032 | Dead - BU2525 LOPTr s/c | When replaced ran hot with smoke from D01 - EW driver chip STV2145 faulty | 14-09-04 |
|
Amstrad | WSTV3032N | Accessing service mode | Enter code 089 | 14-09-04 |
Amstrad | WSTV3032N | Removing child lock | press in this order P+ P- V+ V- with the round central button on the hand set, then press o.k. this has to be done in a quick shot within 4 secs, then the lock will be cleared . | 14-09-04 |
Beko | 30320 | Pic int fades out | Invisible dry joint on LOPTx pin (CRT Htrs) | 14-09-04 |
Beko | 30328T | St/by only | No line - line dr tr T801 o/c | 14-09-04 |
Beko | NR30328 | Dead 1.6A fuse shattered | Dead s/c on chopper caused by s/c chopper tfmr | 14-09-04 |
Beko | NR303281 | Tripping - s/c across LOP | C807 (470pF 2kV) adj to lopt s/c. | 14-09-04 |
Grundig | CUC5303 | No front or R/C controls aft couple of hours | IR Rx | 14-09-04 |
Grundig | CUC5303 | PS. Transistor blown. Changed chopper tr, and TDA4605, But they were blown again. Occasionally the set before blowing the smps may run for a while. | Check/Replace R632 270K Resistor. | 14-09-04 |
Grundig | CUC7303 | Dead - PSU blown | Chopper tfmr, S2055 LOPTr & FOP chip | 14-09-04 |
Grundig | CUC7303 | Dead apart from LED flashing | Sw mode trnfmr o/c winding between pins 5 & 7 (was able to repair) | 14-09-04 |
Grundig | CUC7303 | Dead with mains fuse o/c | Degauss positor | 14-09-04 |
Grundig | CUC7303 | Led blinks at 1 Hz rate,no start-up | Change D667 (BA 157) even if it reads ok!!. | 14-09-04 |
Grundig | CUC7303 | off burning smell | bad joints mains sw | 14-09-04 |
Grundig | CUC7303 | St/by LED blinks (tripping) | D667 BA157 -use BA159 in lieu, UC3842 supply rect (measured ok) also check 0R82 res in emitter, 2 x 1N4004 & res 220R & sm LS4148 diodes & HT control for o/c + chopper Tr & IC | 14-09-04 |
Grundig | CUC7303 | Won't go fully into st/by - crt heaters stay lit etc | Pin 1 IC676 should drop to 1.2v in st/by - was staying at 10.7v. BC848 sm tr downstream from pin 1 was faulty though checked ok | 14-09-04 |
Matsui | 14V1T CUC7303 | Dead - Chopper FET s/c | HT res cap 47µ 385v o/c | 14-09-04 |
Matsui | 20V1 CUC7303 | Dead | Replace T665 (MJF18004), IC630 (UC3842AN), R661 (220R) & D663 (3.6V Zener).caused by dry joint C669 | 14-09-04 |
Matsui | 20V1 CUC7303 | LED pulsing | D667 BA157 - read ok out of cct | 14-09-04 |
Nordemende | 3038 | Dead apart from brief flash of st/by led | RP42 in psu o/c | 14-09-04 |
Philips | 14HT3303 | Service code of the FM-Radio tuner. | In the partslist of the Radio-SP/LS-Vbatt panel of the Chassis Manual L9H.2E, the service code of the FM-Radio tuner item 1901 was not indicated.
The service code is 9352 632 70112 | 14-09-04 |
|
Philips | 20HT3303 | "welcome message" doesn't come up at start up. | When the set is switched off via the mains switch and is switched on again after more than 5 minutes, the "welcome message" doesn't come up at start up.
Put the set into the SDM mode. Select the option AS (Auto start-up).
Change the option content fr | 14-09-04 |
Philips | 20HT3303 | Service code of the FM-Radio tuner. | In the partslist of the Radio-SP/LS-Vbatt panel of the Chassis Manual L9H.2E, the service code of the FM-Radio tuner item 1901 was not indicated.
The service code is 9352 632 70112 | 14-09-04 |
Philips | MD 2.21 AA 28PT7303 | After replacing LOPTx set starts up with brief EHT then reverts to st/by | FET on same heatsink as BU2520 is S/C | 14-09-04 |
Pye | 3030 NC3 | Picture - int. | Dry-joint on R608 ( 18ohm ) | 14-09-04 |