Make | Model | Problem | Solution | Date |
| | | |
Found: 32
|
Daewoo | CP330 | Jumps chans and sound varies | 24C08P Eprom memory chip IV02 - use Daewoo type | 14-09-04 |
Daewoo | CP330/CP365 | Magenta cast after I501 replacement | I501 TDA4661 chroma delay line chip could be faulty | 14-09-04 |
|
Daewoo | CP330/CP365 | No pic or line drive | Check drive pin 37 I701 TDA8362B, if none check 8.2v pin 36, if present replace chip, if absent check R401/2, D401 | 14-09-04 |
Daewoo | CP330/CP365 | Txt absent/garbled | XT01 27Mhz Xtal | 14-09-04 |
Goodmans | 2195T CP330 | Field OP chip TDA3653B has short life (1 week) | C414 22µ pin 4 LOPTx leaky | 14-09-04 |
Grundig | CUC3300 | POOR FOCUS OR PICTURE SO DIM IT CAN HARDLY BE SEEN | C433 1000uF 25v ( NOT 16v AS ORIGINALLY FITTED ) DO NOT RUN SET IN THIS CONDITION AS THE SCAN COILS MAY OVERHEAT AND CRACK CR | 14-09-04 |
Grundig | CUC3300 | Poor purity & focus. | C433 ( 1 , 000uf , 25v ) | 14-09-04 |
Grundig | CUC3300 CUC3400 | Poor focus | Usually the focus pot on tripler faulty but check C433 1000µ for s/c, if its 16v working - fit 25vw (can cause scan coils to overheat) | 14-09-04 |
Grundig | CUC6330 | E/Wfaulty with burning smell | Check R569 for o/c (6R8?), TDA8145 E/W chip - cause dry joint C567 | 14-09-04 |
Grundig | CUC6330 | E-W faulty & narrow pic | R569 4.7R o/c (next to E-W chip TDA8145) | 14-09-04 |
Grundig | CUC6330 | Greenish blank raster with fb lines | No SDL SDA activity - s/c on o/p of IR Rx | 14-09-04 |
Grundig | CUC6330 | greenish blank raster with fb lines - no oSD | no clock pulses on IC811 proc. - s/c on IR Rx o/p IC84001 on front panel | 14-09-04 |
Grundig | CUC6330 | Hotel mode removal | Switch set off, and whilst holding the "i" button switch set on. On screen display gives option of hotel on/off, select off. | 14-09-04 |
Grundig | CUC6330 | Negative looking pic - ok with scart I/p - in wrong standard | In menu set standard (s) to '2' & store with 'OK' key | 14-09-04 |
Grundig | CUC6330 | No Luminance | There is no luma output from filter F120 SFB4595 (part number 8140-601-600) | 14-09-04 |
Grundig | CUC6330 | No pic - crt internal arcing - focus volts too high | LOPTx faulty (Konig FAT30329) | 14-09-04 |
Grundig | CUC6330 | Sync? Reduced line pulse | R176 hi res in flywheel timebase | 14-09-04 |
Grundig | CUC6330 | Tripping | D569 BY228 leaky (next to LOPTr) | 14-09-04 |
ITT | CT23304 Trimline | Low gain. | S/C in tuner IF unit. | 14-09-04 |
ITT | CT23304 Trimline | No colour | IC870 ( TDA3561 ) | 14-09-04 |
ITT | CT23304 Trimline | Sound - low. | Resolder DJ in audio stage. | 14-09-04 |
ITT | CT3306 Mono A | No sync. | C609 ( 100pf ) ceramic off pin 7 TDA2579 | 14-09-04 |
|
Philips | 14HT3303 | Service code of the FM-Radio tuner. | In the partslist of the Radio-SP/LS-Vbatt panel of the Chassis Manual L9H.2E, the service code of the FM-Radio tuner item 1901 was not indicated.
The service code is 9352 632 70112 | 14-09-04 |
Philips | 14PV330 | Dead | D6391 BYW98/200 in psu s/c | 14-09-04 |
Philips | 20HT3303 | "welcome message" doesn't come up at start up. | When the set is switched off via the mains switch and is switched on again after more than 5 minutes, the "welcome message" doesn't come up at start up.
Put the set into the SDM mode. Select the option AS (Auto start-up).
Change the option content fr | 14-09-04 |
Philips | 20HT3303 | Service code of the FM-Radio tuner. | In the partslist of the Radio-SP/LS-Vbatt panel of the Chassis Manual L9H.2E, the service code of the FM-Radio tuner item 1901 was not indicated.
The service code is 9352 632 70112 | 14-09-04 |
Philips | 21PV330/07 Delta 2000 | Dead - LOPTr s/c - blows again few hrs aft replacement | line dr trfmr relacement cured it | 14-09-04 |
Proline | 14PV330 | St/by light flashes & Mech tries to move on its own | R3330 primary PSU. Replace with 3K6. and replace C2351 with 3300mfd. | 14-09-04 |
Samsung | CI330F | Dead - 800Ma fuse blown. | R801 ( posistor ) in degause cct , C805 ( 0.22uf ) | 14-09-04 |
Samsung | CI330F/Z | Dead. | Mains Tx primary o/c - see Tv mag. | 14-09-04 |